Re: [Xen-devel] PVH dom0 creation fails - the system freezes

[Paul Durrant <Paul.Durrant@xxxxxxxxxx>]

> -----Original Message-----
> From: Roger Pau Monne
> Sent: 08 August 2018 09:08
> To: bercarug@xxxxxxxxxx
> Cc: Paul Durrant <Paul.Durrant@xxxxxxxxxx>; xen-devel <xen-
> devel@xxxxxxxxxxxxxxxxxxxx>; David Woodhouse <dwmw2@xxxxxxxxxxxxx>;
> Jan Beulich <JBeulich@xxxxxxxx>; Belgun, Adrian <abelgun@xxxxxxxxxx>
> Subject: Re: [Xen-devel] PVH dom0 creation fails - the system freezes
> 
> On Wed, Aug 08, 2018 at 10:46:40AM +0300, bercarug@xxxxxxxxxx wrote:
> > On 08/02/2018 04:55 PM, Roger Pau Monné wrote:
> > > Please try to avoid top posting.
> > >
> > > On Thu, Aug 02, 2018 at 11:36:26AM +0000, Bercaru, Gabriel wrote:
> > > > I applied the match mentioned, but the system fails to boot. Instead, it
> > > > drops to a BusyBox shell. It seems to be a file system issue.
> > > So you have applied 173c7803592065d27bf2e60d50e08e197a0efa83 and it
> > > causes a regression for you?
> > >
> > > As I understand it, before applying 173c780359206 you where capable of
> > > booting the PVH Dom0, albeit with non-working USB?
> > >
> > > And after applying 173c780359206 you are no longer able to boot?
> > Right, after applying 173c780359206 the system fails to boot (it drops to
> > the BusyBox shell).
> > > > Following is a sequence of the boot log regarding the file system issue.
> > > At least part of the issue seems to be that the IO-APIC information
> > > provided to Dom0 is wrong (from the attached log):
> > >
> > > [    0.000000] IOAPIC[0]: apic_id 2, version 152, address 0xfec00000, GSI 
> > > 0-
> 0
> > > [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 2
> > > [    0.000000] Failed to find ioapic for gsi : 2
> > > [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 9
> > > [    0.000000] Failed to find ioapic for gsi : 9
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 1
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 2
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 3
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 4
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 5
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 6
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 7
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 8
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 9
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 10
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 11
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 12
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 13
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 14
> > > [    0.000000] ERROR: Unable to locate IOAPIC for GSI 15
> > >
> > > Can you try to boot with just the staging branch (current commit is
> > > 008a8fb249b9d433) and see how that goes?
> > >
> > > Thanks, Roger.
> > >
> > I recompiled Xen using the staging branch, commit 008a8fb249b9d433 and
> the
> > system boots,
> 
> OK, so your issues where not caused by 173c780359206 then?
> 
> 008a8fb249b9d433 already contains 173c780359206 because it was
> committed earlier. In any case it's good to know you are able to boot
> (albeit with issues) using the current staging branch.
> 
> > however the USB problem persists. I was able to log in using the serial port
> > and after executing
> 
> Yes, the fixes for this issue have not been committed yet, see:
> 
> https://lists.xenproject.org/archives/html/xen-devel/2018-
> 08/msg00528.html
> 
> If you want you can give this branch a try, it should hopefully solve
> your USB issues.
> 
> > "xl list -l" the memory decrease problem appeared.
> 
> Yup, I will look into this now in order to find some kind of
> workaround.
> 
> > I attached the boot log. Following are some lines extracted from the log,
> > regarding the USB
> >
> > devices problem:
> >
> > [    5.864084] usb 1-1: device descriptor read/64, error -71
> >
> > [    7.564025] usb 1-1: new full-speed USB device number 4 using xhci_hcd
> > [    7.571347] usb 1-1: Device not responding to setup address.
> >
> > [    8.008031] usb 1-1: device not accepting address 4, error -71
> >
> > [    8.609623] usb 1-1: device not accepting address 5, error -71
> >
> >
> > At the beginning of the log, there is a message regarding
> > iommu_inclusive_mapping:
> >
> >
> > (XEN) [VT-D]found ACPI_DMAR_RMRR:
> > (XEN) [VT-D]  RMRR address range 3e2e0000..3e2fffff not in reserved
> memory;
> > need "iommu_inclusive_mapping=1"?
> > (XEN) [VT-D] endpoint: 0000:00:14.0
> >
> >
> > I mention that I tried to boot again using this command line option, but
> > this message and the
> >
> > USB messages persist.
> 
> Yes, iommu_inclusive_mapping doesn't work for PVH, that's what my
> patch series is trying to address. The error is caused by
> missing/wrong RMRR regions in the ACPI tables.
> 

Looks like this warning is suggesting that there is an RMRR that falls outside 
of an E820 reserved region. For PV I guess that 'inclusive' will fix this, but 
for PVH 'reserved' isn't going to fix it. I hope that the range at least falls 
in a hole, so maybe we also need a dom0_iommu=holes option too? Ugly, but maybe 
necessary.

  Paul

> Thanks, Roger.

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxxx
https://lists.xenproject.org/mailman/listinfo/xen-devel