| |
|
 |
|
 |
|
|
|
| |
|
|
xen-users
RE: [Xen-users] Re: Xen 4.0.1 + 2.6.37 missing input from console
> On Fri, 14 Jan 2011 11:52:57 -0800 <a_balandis@xxxxxxxxx> wrote:
>
>
> Here is output from lspci :
>
> 01:00.0 VGA compatible controller: nVidia Corporation Quadro NVS 140M (rev
> a1) (prog-if 00 [VGA controller])
> Subsystem: Lenovo ThinkPad T61
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at d6000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
> Region 3: Memory at d4000000 (64-bit, non-prefetchable) [size=32M]
> Region 5: I/O ports at 2000 [size=128]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+
> Queue=0/0 Enable-
> Address: 0000000000000000 Data: 0000
> Capabilities: [78] Express (v1) Endpoint, MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <512ns, L1 <4us
> ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
> TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1,
> Latency L0 <512ns, L1 <4us
> ClockPM- Suprise- LLActRep- BwNot-
> LnkCtl: ASPM L0s Enabled; RCB 128 bytes Disabled- Retrain-
> CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
> DLActive- BWMgmt- ABWMgmt-
> Capabilities: [100] Virtual Channel <?>
> Capabilities: [128] Power Budgeting <?>
> Capabilities: [600] Vendor Specific Information <?>
> Kernel driver in use: nvidia's
> Kernel modules: nvidia
>
> It's generated from the same vmlinuz-2.6.37xen kernel but run on bare-metal.
Thats ok. Our outputs are slightly different but that is because I assume you did not run the command as root or with sudo. Regardless I am almost certain are video hardware is identical. Therefor I am confident that perticular 2.6.32 kernel with 4.0.1 will work for you (fingers crossed).
-M
|
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
|
|
| |
|
Home