| |
|
 |
|
 |
|
|
|
| |
|
|
xen-users
Re: [Xen-users] Backend device not found!!.-- follow-up
Hi
I'm had similar problems.
I use the network - script from the fc4 beta version and it is workin fine:
-- Timo
########## Network script
vi /etc/xen/scripts/network
#!/bin/sh
#============================================================================
# Default Xen network start/stop script.
# Xend calls a network script when it starts.
# The script name to use is defined in /etc/xen/xend-config.sxp
# in the network-script field.
#
# This script creates a bridge (default xen-br0), adds a device
# (default eth0) to it, copies the IP addresses from the device
# to the bridge and adjusts the routes accordingly.
#
# If all goes well, this should ensure that networking stays up.
# However, some configurations are upset by this, especially
# NFS roots. If the bridged setup does not meet your needs,
# configure a different script, for example using routing instead.
#
# Usage:
#
# network (start|stop|status) {VAR=VAL}*
#
# Vars:
#
# bridge The bridge to use (default xen-br0).
# netdev The interface to add to the bridge (default eth0).
# antispoof Whether to use iptables to prevent spoofing (default yes).
#
# start:
# Creates the bridge and enslaves netdev to it.
# Copies the IP addresses from netdev to the bridge.
# Deletes the routes to netdev and adds them on bridge.
#
# stop:
# Removes netdev from the bridge.
# Deletes the routes to bridge and adds them to netdev.
#
# status:
# Print ifconfig for netdev and bridge.
# Print routes.
#
#============================================================================
# Exit if anything goes wrong.
set -e
# First arg is the operation.
OP=$1
shift
# Pull variables in args in to environment.
for arg ; do export "${arg}" ; done
bridge=${bridge:-xen-br0}
netdev=${netdev:-eth0}
antispoof=${antispoof:-yes}
echo "network $OP bridge=$bridge netdev=$netdev antispoof=$antispoof"
# Usage: transfer_addrs src dst
# Copy all IP addresses (including aliases) from device $src to device $dst.
transfer_addrs () {
local src=$1
local dst=$2
# Don't bother if $dst already has IP addresses.
if ip addr show dev ${dst} | egrep -q '^ *inet ' ; then
return
fi
# Address lines start with 'inet' and have the device in them.
# Replace 'inet' with 'ip addr add' and change the device name $src
# to 'dev $src'. Remove netmask as we'll add routes later.
ip addr show dev ${src} | egrep '^ *inet ' | sed -e "
s/inet/ip addr add/
s@\([0-9]\+\.[0-9]\+\.[0-9]\+\.[0-9]\+\)/[0-9]\+@\1@
s/${src}/dev ${dst}/
" | sh -e
}
# Usage: transfer_routes src dst
# Get all IP routes to device $src, delete them, and
# add the same routes to device $dst.
# The original routes have to be deleted, otherwise adding them
# for $dst fails (duplicate routes).
transfer_routes () {
local src=$1
local dst=$2
# List all routes and grep the ones with $src in.
# Stick 'ip route del' on the front to delete.
# Change $src to $dst and use 'ip route add' to add.
ip route list | grep ${src} | sed -e "
h
s/^/ip route del /
P
g
s/${src}/${dst}/
s/^/ip route add /
P
d
" | sh -e
}
# Usage: create_bridge dev bridge
# Create bridge $bridge and add device $dev to it.
create_bridge () {
local dev=$1
local bridge=$2
# Don't create the bridge if it already exists.
if ! brctl show | grep -q ${bridge} ; then
brctl addbr ${bridge}
brctl stp ${bridge} off
brctl setfd ${bridge} 0
fi
ifconfig ${bridge} up
}
# Usage: antispoofing dev bridge
# Set the default forwarding policy for $dev to drop.
# Allow forwarding to the bridge.
antispoofing () {
local dev=$1
local bridge=$2
iptables -P FORWARD DROP
iptables -A FORWARD -m physdev --physdev-in ${dev} -j ACCEPT
}
# Usage: show_status dev bridge
# Print ifconfig and routes.
show_status () {
local dev=$1
local bridge=$2
echo '============================================================'
ifconfig ${dev}
ifconfig ${bridge}
echo ' '
ip route list
echo ' '
route -n
echo '============================================================'
}
op_start () {
if [ "${bridge}" == "null" ] ; then
return
fi
# Create the bridge and give it the interface IP addresses.
# Move the interface routes onto the bridge.
create_bridge ${netdev} ${bridge}
transfer_addrs ${netdev} ${bridge}
transfer_routes ${netdev} ${bridge}
# Don't add $dev to $bridge if it's already on a bridge.
if ! brctl show | grep -q ${netdev} ; then
brctl addif ${bridge} ${netdev}
fi
if [ ${antispoof} == 'yes' ] ; then
antispoofing ${netdev} ${bridge}
fi
}
op_stop () {
if [ "${bridge}" == "null" ] ; then
return
fi
# Remove the interface from the bridge.
# Move the routes back to the interface.
brctl delif ${bridge} ${netdev}
transfer_routes ${bridge} ${netdev}
# It's not our place to be enabling forwarding...
}
case ${OP} in
start)
op_start
;;
stop)
op_stop
;;
status)
show_status ${netdev} ${bridge}
;;
*)
echo 'Unknown command: ' ${OP}
echo 'Valid commands are: start, stop, status'
exit 1
esac
----- Lamia M.Youseff <lyouseff@xxxxxxxxxxx> kirjoitti:
> Hi again,
>
> I also tested the brctl bridges on the host domain. The output of
> brctl
> is shown below too. I tried adding a new bridge and configuring guest
>
> domain to use it, but with no success. I also tried to turn the STP on
>
> and off for xenbr0, and tested each case with xm create with no
> success
> either.
>
> -bash-3.00# brctl show
> bridge name bridge id STP enabled interfaces
> xenbr0 8000.feffffffffff no vif0.0
>
> peth0
> Any input is appreciated,
> Lamia Youseff
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
|
|
| |
|
Home