[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [RFC PATCH] xen/memory: Introduce a hypercall to provide unallocated space




On 09.08.21 18:42, Julien Grall wrote:
Hi Oleksandr,


Hi Julien.


Thank you for the input.



On 07/08/2021 18:03, Oleksandr wrote:

On 06.08.21 03:30, Stefano Stabellini wrote:

Hi Stefano

On Wed, 4 Aug 2021, Julien Grall wrote:
+#define GUEST_SAFE_RANGE_BASE xen_mk_ullong(0xDE00000000) /* 128GB */
+#define GUEST_SAFE_RANGE_SIZE xen_mk_ullong(0x0200000000)

While the possible new DT bindings has not been agreed yet, I re-used
existing "reg" property under the hypervisor node to pass safe range as a
second region,
https://elixir.bootlin.com/linux/v5.14-rc4/source/Documentation/devicetree/bindings/arm/xen.txt#L10:
So a single region works for a guest today, but for dom0 we will need multiple regions because it is may be difficult to find enough contiguous space for a
single region.

That said, as dom0 is mapped 1:1 (including some guest mapping), there is also the question where to allocate the safe region. For grant table, we so far re-use the Xen address space because it is assumed it will space will always
be bigger than the grant table.

I am not sure yet where we could allocate the safe regions. Stefano, do you
have any ideas?
The safest choice would be the address range corresponding to memory
(/memory) not already allocated to Dom0.

For instance from my last boot logs:
(XEN) Allocating 1:1 mappings totalling 1600MB for dom0:
(XEN) BANK[0] 0x00000010000000-0x00000070000000 (1536MB)
(XEN) BANK[1] 0x00000078000000-0x0000007c000000 (64MB)

All the other ranges could be given as unallocated space:

- 0x0 - 0x10000000
- 0x70000000 - 0x78000000
- 0x8_0000_0000 - 0x8_8000_0000

Thank you for the ideas.

If I got the idea correctly, yes, as these ranges represent the real RAM, so no I/O would be in conflict with them and as the result - no overlaps would be expected. But, I wonder, would this work if we have IOMMU enabled for Dom0 and need to establish 1:1 mapping for the DMA devices to work with grant mappings... In arm_iommu_map_page() we call guest_physmap_add_entry() with gfn = mfn, so the question is could we end up with this new gfn replacing the valid mapping
(with gfn allocated from the safe region)?

Right, when we enable the IOMMU for dom0, Xen will add an extra mapping with GFN == MFN for foreign and grant pages. This is because Linux is not aware that whether a device is protected by an IOMMU. Therefore it is assuming it is not and will use the MFN to configure for DMA transaction.

We can't remove the mapping without significant changes in Linux and Xen. I would not mandate them for this work.

That said, I think it would be acceptable to have different way to find the region depending on the dom0 configuration. So we could use the RAM not used by dom0 when the IOMMU is turned off.

OK



The second best choice would be an hole: an address range not used by
anybody else (no reg property) and also not even mappable by a bus (not
covered by a ranges property). This is not the best choice because there
can cases where physical resources appear afterwards.

Are you saying that the original device-tree doesn't even describe them in any way (i.e. reserved...)?


Unfortunately, yes.

So the decision where the safe region is located will be done by Xen. There is no involvement of the domain (it will discover the region from the DT). Therefore, I don't think we need to think about everything right now as we could adapt this is exact region is not part of the stable ABI.

The hotplug is one I would defer because this is not supported (and quite likely not working) in Xen upstream today.

Sounds reasonable.




Now regarding the case where dom0 is using the IOMMU. The assumption is Xen will be able to figure out all the regions used from the firmware table (ACPI or DT).

AFAIK, this assumption would be correct for DT. However, for ACPI, I remember we were not able to find all the MMIOs region in Xen (see [1] and [2]). So even this solution would not work for ACPI.

If I am not mistaken, we don't support IOMMU with ACPI yet. So we could defer the problem to when this is going to be supported.

Sounds reasonable.


To summarize:

0. Skip ACPI case for now, implement for DT case

1. If IOMMU is enabled for Dom0 -> provide holes found in Host DT as safe ranges

I would take into the account holes >= 1MB. I am wondering, do we need a special alignment here other than a PAGE_SIZE?

2. If IOMMU is disabled for Dom0 -> provide RAM which not assigned to Dom0 as safe ranges

We could even provide holes here as well.




Cheers,

[1] https://marc.info/?l=linux-arm-kernel&m=148469169210500&w=2
[2] Xen commit 80f9c316708400cea4417e36337267d3b26591db

--
Regards,

Oleksandr Tyshchenko




 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.