Re: [PATCH v3 01/11] xen/manage: keep track of the on-going suspend mode

[Anchal Agarwal <anchalag@xxxxxxxxxx>]

On Tue, May 25, 2021 at 06:23:35PM -0400, Boris Ostrovsky wrote:
> CAUTION: This email originated from outside of the organization. Do not click 
> links or open attachments unless you can confirm the sender and know the 
> content is safe.
> 
> 
> 
> On 5/21/21 1:26 AM, Anchal Agarwal wrote:
> >>> What I meant there wrt VCPU info was that VCPU info is not unregistered 
> >>> during hibernation,
> >>> so Xen still remembers the old physical addresses for the VCPU 
> >>> information, created by the
> >>> booting kernel. But since the hibernation kernel may have different 
> >>> physical
> >>> addresses for VCPU info and if mismatch happens, it may cause issues with 
> >>> resume.
> >>> During hibernation, the VCPU info register hypercall is not invoked again.
> >>
> >> I still don't think that's the cause but it's certainly worth having a 
> >> look.
> >>
> > Hi Boris,
> > Apologies for picking this up after last year.
> > I did some dive deep on the above statement and that is indeed the case 
> > that's happening.
> > I did some debugging around KASLR and hibernation using reboot mode.
> > I observed in my debug prints that whenever vcpu_info* address for 
> > secondary vcpu assigned
> > in xen_vcpu_setup at boot is different than what is in the image, resume 
> > gets stuck for that vcpu
> > in bringup_cpu(). That means we have different addresses for 
> > &per_cpu(xen_vcpu_info, cpu) at boot and after
> > control jumps into the image.
> >
> > I failed to get any prints after it got stuck in bringup_cpu() and
> > I do not have an option to send a sysrq signal to the guest or rather get a 
> > kdump.
> 
> 
> xenctx and xen-hvmctx might be helpful.
> 
> 
> > This change is not observed in every hibernate-resume cycle. I am not sure 
> > if this is a bug or an
> > expected behavior.
> > Also, I am contemplating the idea that it may be a bug in xen code getting 
> > triggered only when
> > KASLR is enabled but I do not have substantial data to prove that.
> > Is this a coincidence that this always happens for 1st vcpu?
> > Moreover, since hypervisor is not aware that guest is hibernated and it 
> > looks like a regular shutdown to dom0 during reboot mode,
> > will re-registering vcpu_info for secondary vcpu's even plausible?
> 
> 
> I think I am missing how this is supposed to work (maybe we've talked about 
> this but it's been many months since then). You hibernate the guest and it 
> writes the state to swap. The guest is then shut down? And what's next? How 
> do you wake it up?
> 
> 
> -boris
> 
To resume a guest, guest boots up as the fresh guest and then software_resume()
is called which if finds a stored hibernation image, quiesces the devices and 
loads 
the memory contents from the image. The control then transfers to the targeted 
kernel.
This further disables non boot cpus,sycore_suspend/resume callbacks are invoked 
which sets up
the shared_info, pvclock, grant tables etc. Since the vcpu_info pointer for each
non-boot cpu is already registered, the hypercall does not happen again when
bringing up the non boot cpus. This leads to inconsistencies as pointed
out earlier when KASLR is enabled.

Thanks,
Anchal
> 
> 
> >  I could definitely use some advice to debug this further.
> >
> >
> > Some printk's from my debugging:
> >
> > At Boot:
> >
> > xen_vcpu_setup: xen_have_vcpu_info_placement=1 cpu=1, 
> > vcpup=0xffff9e548fa560e0, info.mfn=3996246 info.offset=224,
> >
> > Image Loads:
> > It ends up in the condition:
> >  xen_vcpu_setup()
> >  {
> >  ...
> >  if (xen_hvm_domain()) {
> >         if (per_cpu(xen_vcpu, cpu) == &per_cpu(xen_vcpu_info, cpu))
> >                 return 0;
> >  }
> >  ...
> >  }
> >
> > xen_vcpu_setup: checking mfn on resume cpu=1, info.mfn=3934806 
> > info.offset=224, &per_cpu(xen_vcpu_info, cpu)=0xffff9d7240a560e0
> >
> > This is tested on c4.2xlarge [8vcpu 15GB mem] instance with 5.10 kernel 
> > running
> > in the guest.
> >
> > Thanks,
> > Anchal.
> >> -boris
> >>
> >>