[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [RFC PATCH v3 6/6] of: Add plumbing for restricted DMA pool



On Fri, Jan 15, 2021 at 2:52 AM Florian Fainelli <f.fainelli@xxxxxxxxx> wrote:
>
> On 1/14/21 1:08 AM, Claire Chang wrote:
> > On Wed, Jan 13, 2021 at 7:48 AM Florian Fainelli <f.fainelli@xxxxxxxxx> 
> > wrote:
> >>
> >> On 1/5/21 7:41 PM, Claire Chang wrote:
> >>> If a device is not behind an IOMMU, we look up the device node and set
> >>> up the restricted DMA when the restricted-dma-pool is presented.
> >>>
> >>> Signed-off-by: Claire Chang <tientzu@xxxxxxxxxxxx>
> >>> ---
> >>
> >> [snip]
> >>
> >>> +int of_dma_set_restricted_buffer(struct device *dev)
> >>> +{
> >>> +     struct device_node *node;
> >>> +     int count, i;
> >>> +
> >>> +     if (!dev->of_node)
> >>> +             return 0;
> >>> +
> >>> +     count = of_property_count_elems_of_size(dev->of_node, 
> >>> "memory-region",
> >>> +                                             sizeof(phandle));
> >>
> >> You could have an early check for count < 0, along with an error
> >> message, if that is deemed useful.
> >>
> >>> +     for (i = 0; i < count; i++) {
> >>> +             node = of_parse_phandle(dev->of_node, "memory-region", i);
> >>> +             if (of_device_is_compatible(node, "restricted-dma-pool"))
> >>
> >> And you may want to add here an of_device_is_available(node). A platform
> >> that provides the Device Tree firmware and try to support multiple
> >> different SoCs may try to determine if an IOMMU is present, and if it
> >> is, it could be marking the restriced-dma-pool region with a 'status =
> >> "disabled"' property, or any variant of that scheme.
> >
> > This function is called only when there is no IOMMU present (check in
> > drivers/of/device.c). I can still add of_device_is_available(node)
> > here if you think it's helpful.
>
> I believe it is, since boot loader can have a shared Device Tree blob
> skeleton and do various adaptations based on the chip (that's what we
> do) and adding a status property is much simpler than insertion new
> nodes are run time.
>
> >
> >>
> >>> +                     return of_reserved_mem_device_init_by_idx(
> >>> +                             dev, dev->of_node, i);
> >>
> >> This does not seem to be supporting more than one memory region, did not
> >> you want something like instead:
> >>
> >>                 ret = of_reserved_mem_device_init_by_idx(...);
> >>                 if (ret)
> >>                         return ret;
> >>
> >
> > Yes. This implement only supports one restriced-dma-pool memory region
> > with the assumption that there is only one memory region with the
> > compatible string, restricted-dma-pool, in the dts. IIUC, it's similar
> > to shared-dma-pool.
>
> Then if here is such a known limitation it should be both documented and
> enforced here, you shouldn ot be iterating over all of the phandles that
> you find, stop at the first one and issue a warning if count > 1?

What I have in mind is there might be multiple memory regions, but
only one is for restriced-dma-pool.
Say, if you want a separated region for coherent DMA and only do
streaming DMA in this restriced-dma-pool region, you can add another
reserved-memory node with shared-dma-pool in dts and the current
implementation will try to allocate the memory via
dma_alloc_from_dev_coherent() first (see dma_alloc_attrs() in
/kernel/dma/mapping.c).
Or if you have vendor specific memory region, you can still set up
restriced-dma-pool by adding another reserved-memory node in dts.
Dose this make sense to you? I'll document this for sure.

> --
> Florian



 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.