[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Xen-devel] [PATCH] docs/xl: Clarify documentation for mem-max and mem-set



mem-set is the primary command that users will need to use and
understand.  Move it first, and clarify the wording; also specify that
you can't set the target higher than maxmem from the domain config.

mem-max is actually a pretty useless command at the moment.  Clarify
that users are not expected to use it; and document all of its quirky
behavior.

Signed-off-by: George Dunlap <george.dunlap@xxxxxxxxxx>
---
I'm actully somewhat tempted to take out the entry for mem-max
entirely -- it's not at all clear to me what anyone would use it for,
and it's only likely to confuse people.

CC: Ian Jackson <ian.jackson@xxxxxxxxxx>
CC: Wei Liu <wei.liu2@xxxxxxxxxx>
CC: Andrew Cooper <andrew.cooper3@xxxxxxxxxx>
CC: Jan Beulich <jbeulich@xxxxxxxx>
CC: Tim Deegan <tim@xxxxxxx>
CC: Konrad Wilk <konrad.wilk@xxxxxxxxxx>
CC: Stefano Stabellini <sstabellini@xxxxxxxxxx>
CC: Julien Grall <julien.grall@xxxxxxx>
CC: Lars Kurth <lars.kurth@xxxxxxxxxx>
---
 docs/man/xl.pod.1.in | 72 ++++++++++++++++++++++++++++++--------------
 1 file changed, 50 insertions(+), 22 deletions(-)

diff --git a/docs/man/xl.pod.1.in b/docs/man/xl.pod.1.in
index b74764dcd3..1d3dabf185 100644
--- a/docs/man/xl.pod.1.in
+++ b/docs/man/xl.pod.1.in
@@ -393,40 +393,68 @@ less utilized than a high CPU workload.  Consider 
yourself warned.
 
 =back
 
-=item B<mem-max> I<domain-id> I<mem>
+=item B<mem-set> I<domain-id> I<mem>
 
-Specify the maximum amount of memory the domain is able to use, appending 't'
-for terabytes, 'g' for gigabytes, 'm' for megabytes, 'k' for kilobytes and 'b'
-for bytes.
+Set the target for the domain's balloon driver.  Append 't' for
+terabytes, 'g' for gigabytes, 'm' for megabytes, 'k' for kilobytes
+and 'b' for bytes.
 
-The mem-max value may not correspond to the actual memory used in the
-domain, as it may balloon down its memory to give more back to the OS.
+This must be less than the initial B<maxmem> parameter in the domain's
+configuration.
 
-The value given just sets the memory amount the domain is allowed to allocate
-in the hypervisor. It can't be set lower than the current reservation, but
-it is allowed to be higher than the configured maximum memory size of the
-domain (B<maxmem> parameter in the domain's configuration). Using B<xl mem-max>
-to set the maximum memory above the initial B<maxmem> value will not allow the
-additional memory to be used via B<xl mem-set>. The initial B<maxmem> value is
-still used as an upper limit for B<xl mem-set>.
+Note that this operation requests the guest operating system's balloon
+driver to reach the target amount of memory.  The guest may fail to
+reach that amount of memory for any number of reasons, including:
 
-The domain will not receive any signal regarding the changed memory limit.
+=over 4
 
-=item B<mem-set> I<domain-id> I<mem>
+=item
+
+The guest doesn't have a balloon driver installed
+
+=item
+
+The guest's balloon driver is buggy
+
+=item
+
+The guest's balloon driver cannot create free guest memory due to
+guest memory pressure
+
+=item
 
-Set the domain's used memory using the balloon driver; append 't' for
-terabytes, 'g' for gigabytes, 'm' for megabytes, 'k' for kilobytes and 'b' for
-bytes.
+The guest's balloon driver cannot allocate memory from Xen because of
+hypervisor memory pressure
 
-Because this operation requires cooperation from the domain operating
-system, there is no guarantee that it will succeed.  This command will
-definitely not work unless the domain has the required paravirt
-driver.
+=item
+
+The guest administrator has disabled the balloon driver
+
+=back
 
 B<Warning:> There is no good way to know in advance how small of a
 mem-set will make a domain unstable and cause it to crash.  Be very
 careful when using this command on running domains.
 
+=item B<mem-max> I<domain-id> I<mem>
+
+Specify the limit Xen will place on the amount of memory a guest may
+allocate. Append 't' for terabytes, 'g' for gigabytes, 'm' for
+megabytes, 'k' for kilobytes and 'b' for bytes.
+
+NB that users normally shouldn't need this command; B<xl mem-set> will
+set this as appropriate automatically.
+
+I<mem> can't be set lower than the current memory target for
+I<domain-id>.  It is allowed to be higher than the configured maximum
+memory size of the domain (B<maxmem> parameter in the domain's
+configuration). Note however that the initial B<maxmem> value is still
+used as an upper limit for B<xl mem-set>.  Also note that calling B<xl
+mem-set> will reset this value.
+
+The domain will not receive any signal regarding the changed memory
+limit.
+
 =item B<migrate> [I<OPTIONS>] I<domain-id> I<host>
 
 Migrate a domain to another host machine. By default B<xl> relies on ssh as a
-- 
2.18.0


_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxxx
https://lists.xenproject.org/mailman/listinfo/xen-devel

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.