[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-devel] [PATCH v3 1/2] xen/arm: Add MVEBU UART driver for Marvell Armada 3700 SoC



On 05/04/18 11:16, Amit Singh Tomar wrote:
> This patch adds driver for UART controller found on Armada 3700 SoC.
> 
> There is no reference manuals available for 3700 SoC in public and it
> is derived by looking at Linux driver[1].
> 
> [1]https://github.com/torvalds/linux/blob/master/drivers/tty/serial/mvebu-uart.c
> 
> Signed-off-by: Amit Singh Tomar <amittomer25@xxxxxxxxx>

Works like a charm, can log into Dom0, Xen console works as well. So in
addition to my Reviewed-by:

Tested-by: Andre Przywara <andre.przywara@xxxxxxx>

Cheers,
Andre.

> ---
> Changes since v2:
>     * Addressed Andre's comments.
> Changes since v1:
>     * Addressed Wei Liu's comments
>     * Addressed Andre's comments.
> Changes since RFC:
>     * Addressed Julien's comments.
> ---
>  xen/drivers/char/Kconfig      |   8 ++
>  xen/drivers/char/Makefile     |   1 +
>  xen/drivers/char/mvebu-uart.c | 296 
> ++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 305 insertions(+)
>  create mode 100644 xen/drivers/char/mvebu-uart.c
> 
> diff --git a/xen/drivers/char/Kconfig b/xen/drivers/char/Kconfig
> index fb53dd8..04a4087 100644
> --- a/xen/drivers/char/Kconfig
> +++ b/xen/drivers/char/Kconfig
> @@ -12,6 +12,14 @@ config HAS_CADENCE_UART
>         This selects the Xilinx Zynq Cadence UART. If you have a Xilinx Zynq
>         based board, say Y.
> 
> +config HAS_MVEBU
> +    bool
> +    default y
> +    depends on ARM_64
> +    help
> +      This selects the Marvell MVEBU UART. If you have a ARMADA 3700
> +      based board, say Y.
> +
>  config HAS_PL011
>       bool
>       default y
> diff --git a/xen/drivers/char/Makefile b/xen/drivers/char/Makefile
> index 0d48b16..b68c330 100644
> --- a/xen/drivers/char/Makefile
> +++ b/xen/drivers/char/Makefile
> @@ -3,6 +3,7 @@ obj-$(CONFIG_HAS_NS16550) += ns16550.o
>  obj-$(CONFIG_HAS_CADENCE_UART) += cadence-uart.o
>  obj-$(CONFIG_HAS_PL011) += pl011.o
>  obj-$(CONFIG_HAS_EXYNOS4210) += exynos4210-uart.o
> +obj-$(CONFIG_HAS_MVEBU) += mvebu-uart.o
>  obj-$(CONFIG_HAS_OMAP) += omap-uart.o
>  obj-$(CONFIG_HAS_SCIF) += scif-uart.o
>  obj-$(CONFIG_HAS_EHCI) += ehci-dbgp.o
> diff --git a/xen/drivers/char/mvebu-uart.c b/xen/drivers/char/mvebu-uart.c
> new file mode 100644
> index 0000000..1561a50
> --- /dev/null
> +++ b/xen/drivers/char/mvebu-uart.c
> @@ -0,0 +1,296 @@
> +/*
> + * xen/drivers/char/mvebu3700-uart.c
> + *
> + * Driver for Marvell MVEBU UART.
> + *
> + * Copyright (c) 2018, Amit Singh Tomar <amittomer25@xxxxxxxxx>.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms and conditions of the GNU General Public
> + * License, version 2, as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
> + * General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public
> + * License along with this program; If not, see 
> <http://www.gnu.org/licenses/>.
> + */
> +
> +#include <xen/irq.h>
> +#include <xen/serial.h>
> +#include <xen/vmap.h>
> +#include <asm/io.h>
> +
> +/* Register offsets */
> +#define UART_RX_REG             0x00
> +
> +#define UART_TX_REG             0x04
> +
> +#define UART_CTRL_REG           0x08
> +#define CTRL_TXFIFO_RST         BIT(15)
> +#define CTRL_RXFIFO_RST         BIT(14)
> +#define CTRL_TX_RDY_INT         BIT(5)
> +#define CTRL_RX_RDY_INT         BIT(4)
> +#define CTRL_BRK_DET_INT        BIT(3)
> +#define CTRL_FRM_ERR_INT        BIT(2)
> +#define CTRL_PAR_ERR_INT        BIT(1)
> +#define CTRL_OVR_ERR_INT        BIT(0)
> +#define CTRL_ERR_INT            (CTRL_BRK_DET_INT | CTRL_FRM_ERR_INT | \
> +                                 CTRL_PAR_ERR_INT | CTRL_OVR_ERR_INT)
> +
> +#define UART_STATUS_REG         0x0c
> +#define STATUS_TXFIFO_EMP       BIT(13)
> +#define STAT_TX_FIFO_FUL        BIT(11)
> +#define STAT_TX_FIFO_HFL        BIT(10)
> +#define STATUS_TX_RDY           BIT(5)
> +#define STATUS_RX_RDY           BIT(4)
> +#define STATUS_BRK_DET          BIT(3)
> +#define STATUS_FRM_ERR          BIT(2)
> +#define STATUS_PAR_ERR          BIT(1)
> +#define STATUS_OVR_ERR          BIT(0)
> +#define STATUS_BRK_ERR          (STATUS_BRK_DET | STATUS_FRM_ERR | \
> +                                 STATUS_PAR_ERR | STATUS_OVR_ERR)
> +
> +#define TX_FIFO_SIZE            32
> +
> +static struct mvebu3700_uart {
> +    unsigned int irq;
> +    void __iomem *regs;
> +    struct irqaction irqaction;
> +    struct vuart_info vuart;
> +} mvebu3700_com = {0};
> +
> +#define mvebu3700_read(uart, off)           readl((uart)->regs + off)
> +#define mvebu3700_write(uart, off, val)     writel(val, (uart->regs) + off)
> +
> +static void mvebu3700_uart_interrupt(int irq, void *data,
> +                                     struct cpu_user_regs *regs)
> +{
> +    struct serial_port *port = data;
> +    struct mvebu3700_uart *uart = port->uart;
> +    uint32_t st = mvebu3700_read(uart, UART_STATUS_REG);
> +
> +    if ( st & (STATUS_RX_RDY | STATUS_OVR_ERR | STATUS_FRM_ERR |
> +               STATUS_BRK_DET) )
> +        serial_rx_interrupt(port, regs);
> +
> +    if ( st & STATUS_TX_RDY )
> +        serial_tx_interrupt(port, regs);
> +}
> +
> +static void __init mvebu3700_uart_init_preirq(struct serial_port *port)
> +{
> +    struct mvebu3700_uart *uart = port->uart;
> +    uint32_t reg;
> +
> +    reg = mvebu3700_read(uart, UART_CTRL_REG);
> +    reg |= (CTRL_TXFIFO_RST | CTRL_RXFIFO_RST);
> +    mvebu3700_write(uart, UART_CTRL_REG, reg);
> +
> +    /* Before we make IRQ request, clear the error bits of state register. */
> +    reg = mvebu3700_read(uart, UART_STATUS_REG);
> +    reg |= STATUS_BRK_ERR;
> +    mvebu3700_write(uart, UART_STATUS_REG, reg);
> +
> +    /* Clear error interrupts. */
> +    mvebu3700_write(uart, UART_CTRL_REG, CTRL_ERR_INT);
> +
> +    /* Disable Rx/Tx interrupts. */
> +    reg = mvebu3700_read(uart, UART_CTRL_REG);
> +    reg &= ~(CTRL_RX_RDY_INT | CTRL_TX_RDY_INT);
> +    mvebu3700_write(uart, UART_CTRL_REG, reg);
> +}
> +
> +static void __init mvebu3700_uart_init_postirq(struct serial_port *port)
> +{
> +    struct mvebu3700_uart *uart = port->uart;
> +    uint32_t reg;
> +
> +    if ( uart->irq > 0 )
> +    {
> +        uart->irqaction.handler = mvebu3700_uart_interrupt;
> +        uart->irqaction.name    = "mvebu3700_uart";
> +        uart->irqaction.dev_id  = port;
> +    }
> +
> +    if ( setup_irq(uart->irq, 0, &uart->irqaction) != 0 )
> +    {
> +        printk("Failed to allocated mvebu3700_uart IRQ %d\n", uart->irq);
> +        return;
> +    }
> +
> +    /* Make sure Rx/Tx interrupts are enabled now */
> +    reg = mvebu3700_read(uart, UART_CTRL_REG);
> +    reg |= (CTRL_RX_RDY_INT | CTRL_TX_RDY_INT);
> +    mvebu3700_write(uart, UART_CTRL_REG, reg);
> +}
> +
> +static void mvebu3700_uart_suspend(struct serial_port *port)
> +{
> +    BUG();
> +}
> +
> +static void mvebu3700_uart_resume(struct serial_port *port)
> +{
> +    BUG();
> +}
> +
> +static void mvebu3700_uart_putc(struct serial_port *port, char c)
> +{
> +    struct mvebu3700_uart *uart = port->uart;
> +
> +    mvebu3700_write(uart, UART_TX_REG, c);
> +}
> +
> +static int mvebu3700_uart_getc(struct serial_port *port, char *c)
> +{
> +    struct mvebu3700_uart *uart = port->uart;
> +
> +    if ( !(mvebu3700_read(uart, UART_STATUS_REG) & STATUS_RX_RDY) )
> +        return 0;
> +
> +    *c = mvebu3700_read(uart, UART_RX_REG) & 0xff;
> +
> +    return 1;
> +}
> +
> +static int __init mvebu3700_irq(struct serial_port *port)
> +{
> +    struct mvebu3700_uart *uart = port->uart;
> +
> +    return (uart->irq > 0) ? uart->irq : -1;
> +}
> +
> +static const struct vuart_info *mvebu3700_vuart_info(struct serial_port 
> *port)
> +{
> +    struct mvebu3700_uart *uart = port->uart;
> +
> +    return &uart->vuart;
> +}
> +
> +static void mvebu3700_uart_stop_tx(struct serial_port *port)
> +{
> +    struct mvebu3700_uart *uart = port->uart;
> +    uint32_t reg;
> +
> +    reg = mvebu3700_read(uart, UART_CTRL_REG);
> +    reg &= ~CTRL_TX_RDY_INT;
> +    mvebu3700_write(uart, UART_CTRL_REG, reg);
> +}
> +
> +static void mvebu3700_uart_start_tx(struct serial_port *port)
> +{
> +    struct mvebu3700_uart *uart = port->uart;
> +    uint32_t reg;
> +
> +    reg = mvebu3700_read(uart, UART_CTRL_REG);
> +    reg |= CTRL_TX_RDY_INT;
> +    mvebu3700_write(uart, UART_CTRL_REG, reg);
> +}
> +
> +static int mvebu3700_uart_tx_ready(struct serial_port *port)
> +{
> +    struct mvebu3700_uart *uart = port->uart;
> +    uint32_t reg;
> +
> +    reg = mvebu3700_read(uart, UART_STATUS_REG);
> +
> +    if ( reg & STATUS_TXFIFO_EMP )
> +        return TX_FIFO_SIZE;
> +    if ( reg & STAT_TX_FIFO_FUL )
> +        return 0;
> +    if ( reg & STAT_TX_FIFO_HFL )
> +        return TX_FIFO_SIZE / 2;
> +
> +    /* if we reach here, we don't know the number of free char in FIFO
> +     * but we are sure that neither the FIFO is full nor empty.
> +     * So, let's just return at least 1.
> +     */
> +    return 1;
> +}
> +
> +static struct uart_driver __read_mostly mvebu3700_uart_driver = {
> +    .init_preirq  = mvebu3700_uart_init_preirq,
> +    .init_postirq = mvebu3700_uart_init_postirq,
> +    .endboot      = NULL,
> +    .suspend      = mvebu3700_uart_suspend,
> +    .resume       = mvebu3700_uart_resume,
> +    .putc         = mvebu3700_uart_putc,
> +    .getc         = mvebu3700_uart_getc,
> +    .tx_ready     = mvebu3700_uart_tx_ready,
> +    .stop_tx      = mvebu3700_uart_stop_tx,
> +    .start_tx     = mvebu3700_uart_start_tx,
> +    .irq          = mvebu3700_irq,
> +    .vuart_info   = mvebu3700_vuart_info,
> +};
> +
> +static int __init mvebu_uart_init(struct dt_device_node *dev, const void 
> *data)
> +{
> +    const char *config = data;
> +    struct mvebu3700_uart *uart;
> +    int res;
> +    u64 addr, size;
> +
> +    if ( strcmp(config, "") )
> +        printk("WARNING: UART configuration is not supported\n");
> +
> +    uart = &mvebu3700_com;
> +
> +    res = dt_device_get_address(dev, 0, &addr, &size);
> +    if ( res )
> +    {
> +        printk("mvebu3700: Unable to retrieve the base address of the 
> UART\n");
> +        return res;
> +    }
> +
> +    res = platform_get_irq(dev, 0);
> +    if ( res < 0 )
> +    {
> +        printk("mvebu3700: Unable to retrieve the IRQ\n");
> +        return -EINVAL;
> +    }
> +
> +    uart->irq  = res;
> +
> +    uart->regs = ioremap_nocache(addr, size);
> +    if ( !uart->regs )
> +    {
> +        printk("mvebu3700: Unable to map the UART memory\n");
> +        return -ENOMEM;
> +    }
> +
> +    uart->vuart.base_addr = addr;
> +    uart->vuart.size = size;
> +    uart->vuart.data_off = UART_CTRL_REG;
> +    uart->vuart.status_off = UART_STATUS_REG;
> +    uart->vuart.status = STATUS_TX_RDY | STATUS_RX_RDY;
> +
> +    /* Register with generic serial driver. */
> +    serial_register_uart(SERHND_DTUART, &mvebu3700_uart_driver, uart);
> +
> +    dt_device_set_used_by(dev, DOMID_XEN);
> +
> +    return 0;
> +}
> +
> +static const struct dt_device_match mvebu_dt_match[] __initconst =
> +{
> +    DT_MATCH_COMPATIBLE("marvell,armada-3700-uart"),
> +    { /* sentinel */ },
> +};
> +
> +DT_DEVICE_START(mvebu, "Marvell Armada-3700 UART", DEVICE_SERIAL)
> +    .dt_match = mvebu_dt_match,
> +    .init = mvebu_uart_init,
> +DT_DEVICE_END
> +
> +/*
> + * Local variables:
> + * mode: C
> + * c-file-style: "BSD"
> + * c-basic-offset: 4
> + * indent-tabs-mode: nil
> + * End:
> + */
> --
> 1.9.1
> 


_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxxx
https://lists.xenproject.org/mailman/listinfo/xen-devel

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.