|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] [Xen-devel] [RFC PATCH 07/12] hvmloader: allocate MMCONFIG area in the MMIO hole + minor code refactoring
Much like normal PCI BARs or other chipset-specific memory-mapped
resources, MMCONFIG area needs space in MMIO hole, so we must allocate
it manually.
The actual MMCONFIG size depends on a number of PCI buses available which
should be covered by ECAM. Possible options are 64MB, 128MB and 256MB.
As we are limited to the bus 0 currently, thus using lowest possible
setting (64MB), #defined via PCI_MAX_MCFG_BUSES in hvmloader/config.h.
When multiple PCI buses support for Xen will be implemented,
PCI_MAX_MCFG_BUSES may be changed to calculation of the number of buses
according to results of the PCI devices enumeration.
The way to allocate MMCONFIG range in MMIO hole is similar to how other
PCI BARs are allocated. The patch extends 'bars' structure to make
it universal for any arbitrary BAR type -- either IO, MMIO, ROM or
a chipset-specific resource.
One important new field is addr_mask, which tells which bits of the base
address can (should) be written. Different address types (ROM, MMIO BAR,
PCIEXBAR) will have different addr_mask values.
For every assignable BAR range we store its size, PCI device BDF (devfn
actually) to which it belongs, BAR type (mem/io/mem64) and corresponding
register offset in device PCI conf space. This way we can insert MMCONFIG
entry into bars array in the same manner like for any other BARs. In this
case, the devfn field will point to MCH PCI device and bar_reg will
contain PCIEXBAR register offset. It will be assigned a slot in MMIO hole
later in a very same way like for plain PCI BARs, with respect to its size
alignment.
Also, to reduce code complexity, all long mem/mem64 BAR flags checks are
replaced by simple bars[i] field probing, eg.:
- if ( (bar_reg == PCI_ROM_ADDRESS) ||
- ((bar_data & PCI_BASE_ADDRESS_SPACE) ==
- PCI_BASE_ADDRESS_SPACE_MEMORY) )
+ if ( bars[i].is_mem )
Signed-off-by: Alexey Gerasimenko <x1917x@xxxxxxxxx>
---
tools/firmware/hvmloader/config.h | 4 ++
tools/firmware/hvmloader/pci.c | 127 ++++++++++++++++++++++++++++--------
tools/firmware/hvmloader/pci_regs.h | 2 +
3 files changed, 106 insertions(+), 27 deletions(-)
diff --git a/tools/firmware/hvmloader/config.h
b/tools/firmware/hvmloader/config.h
index 6fde6b7b60..5443ecd804 100644
--- a/tools/firmware/hvmloader/config.h
+++ b/tools/firmware/hvmloader/config.h
@@ -53,10 +53,14 @@ extern uint8_t ioapic_version;
#define PCI_ISA_DEVFN 0x08 /* dev 1, fn 0 */
#define PCI_ISA_IRQ_MASK 0x0c20U /* ISA IRQs 5,10,11 are PCI connected */
#define PCI_ICH9_LPC_DEVFN 0xf8 /* dev 31, fn 0 */
+#define PCI_MCH_DEVFN 0 /* bus 0, dev 0, func 0 */
/* MMIO hole: Hardcoded defaults, which can be dynamically expanded. */
#define PCI_MEM_END 0xfc000000
+/* possible values are: 64, 128, 256 */
+#define PCI_MAX_MCFG_BUSES 64
+
#define ACPI_TIS_HDR_ADDRESS 0xFED40F00UL
extern unsigned long pci_mem_start, pci_mem_end;
diff --git a/tools/firmware/hvmloader/pci.c b/tools/firmware/hvmloader/pci.c
index 033bd20992..6de124bbd5 100644
--- a/tools/firmware/hvmloader/pci.c
+++ b/tools/firmware/hvmloader/pci.c
@@ -158,9 +158,10 @@ static void class_specific_pci_device_setup(uint16_t
vendor_id,
void pci_setup(void)
{
- uint8_t is_64bar, using_64bar, bar64_relocate = 0;
+ uint8_t is_64bar, using_64bar, bar64_relocate = 0, is_mem;
uint32_t devfn, bar_reg, cmd, bar_data, bar_data_upper;
uint64_t base, bar_sz, bar_sz_upper, mmio_total = 0;
+ uint64_t addr_mask;
uint16_t vendor_id, device_id;
unsigned int bar, pin, link, isa_irq;
int is_running_on_q35 = 0;
@@ -172,10 +173,14 @@ void pci_setup(void)
/* Create a list of device BARs in descending order of size. */
struct bars {
- uint32_t is_64bar;
uint32_t devfn;
uint32_t bar_reg;
uint64_t bar_sz;
+ uint64_t addr_mask; /* which bits of the base address can be written */
+ uint32_t bar_data; /* initial value - BAR flags here */
+ uint8_t is_64bar;
+ uint8_t is_mem;
+ uint8_t padding[2];
} *bars = (struct bars *)scratch_start;
unsigned int i, nr_bars = 0;
uint64_t mmio_hole_size = 0;
@@ -259,13 +264,21 @@ void pci_setup(void)
bar_reg = PCI_ROM_ADDRESS;
bar_data = pci_readl(devfn, bar_reg);
+
+ is_mem = !!(((bar_data & PCI_BASE_ADDRESS_SPACE) ==
+ PCI_BASE_ADDRESS_SPACE_MEMORY) ||
+ (bar_reg == PCI_ROM_ADDRESS));
+
if ( bar_reg != PCI_ROM_ADDRESS )
{
- is_64bar = !!((bar_data & (PCI_BASE_ADDRESS_SPACE |
- PCI_BASE_ADDRESS_MEM_TYPE_MASK)) ==
- (PCI_BASE_ADDRESS_SPACE_MEMORY |
+ is_64bar = !!(is_mem &&
+ ((bar_data & PCI_BASE_ADDRESS_MEM_TYPE_MASK) ==
PCI_BASE_ADDRESS_MEM_TYPE_64));
+
pci_writel(devfn, bar_reg, ~0);
+
+ addr_mask = is_mem ? PCI_BASE_ADDRESS_MEM_MASK
+ : PCI_BASE_ADDRESS_IO_MASK;
}
else
{
@@ -273,28 +286,35 @@ void pci_setup(void)
pci_writel(devfn, bar_reg,
(bar_data | PCI_ROM_ADDRESS_MASK) &
~PCI_ROM_ADDRESS_ENABLE);
+
+ addr_mask = PCI_ROM_ADDRESS_MASK;
}
+
bar_sz = pci_readl(devfn, bar_reg);
pci_writel(devfn, bar_reg, bar_data);
if ( bar_reg != PCI_ROM_ADDRESS )
- bar_sz &= (((bar_data & PCI_BASE_ADDRESS_SPACE) ==
- PCI_BASE_ADDRESS_SPACE_MEMORY) ?
- PCI_BASE_ADDRESS_MEM_MASK :
- (PCI_BASE_ADDRESS_IO_MASK & 0xffff));
+ bar_sz &= is_mem ? PCI_BASE_ADDRESS_MEM_MASK :
+ (PCI_BASE_ADDRESS_IO_MASK & 0xffff);
else
bar_sz &= PCI_ROM_ADDRESS_MASK;
- if (is_64bar) {
+
+ if (is_64bar)
+ {
bar_data_upper = pci_readl(devfn, bar_reg + 4);
pci_writel(devfn, bar_reg + 4, ~0);
bar_sz_upper = pci_readl(devfn, bar_reg + 4);
pci_writel(devfn, bar_reg + 4, bar_data_upper);
bar_sz = (bar_sz_upper << 32) | bar_sz;
}
+
bar_sz &= ~(bar_sz - 1);
if ( bar_sz == 0 )
continue;
+ /* leave only memtype/enable bits etc */
+ bar_data &= ~addr_mask;
+
for ( i = 0; i < nr_bars; i++ )
if ( bars[i].bar_sz < bar_sz )
break;
@@ -302,14 +322,15 @@ void pci_setup(void)
if ( i != nr_bars )
memmove(&bars[i+1], &bars[i], (nr_bars-i) * sizeof(*bars));
- bars[i].is_64bar = is_64bar;
- bars[i].devfn = devfn;
- bars[i].bar_reg = bar_reg;
- bars[i].bar_sz = bar_sz;
+ bars[i].is_64bar = is_64bar;
+ bars[i].is_mem = is_mem;
+ bars[i].devfn = devfn;
+ bars[i].bar_reg = bar_reg;
+ bars[i].bar_sz = bar_sz;
+ bars[i].addr_mask = addr_mask;
+ bars[i].bar_data = bar_data;
- if ( ((bar_data & PCI_BASE_ADDRESS_SPACE) ==
- PCI_BASE_ADDRESS_SPACE_MEMORY) ||
- (bar_reg == PCI_ROM_ADDRESS) )
+ if ( is_mem )
mmio_total += bar_sz;
nr_bars++;
@@ -339,6 +360,63 @@ void pci_setup(void)
pci_writew(devfn, PCI_COMMAND, cmd);
}
+ /*
+ * Calculate MMCONFIG area size and squeeze it into the bars array
+ * for assigning a slot in the MMIO hole
+ */
+ if (is_running_on_q35)
+ {
+ /* disable PCIEXBAR decoding for now */
+ pci_writel(PCI_MCH_DEVFN, PCI_MCH_PCIEXBAR, 0);
+ pci_writel(PCI_MCH_DEVFN, PCI_MCH_PCIEXBAR + 4, 0);
+
+#define PCIEXBAR_64_BUSES (2 << 1)
+#define PCIEXBAR_128_BUSES (1 << 1)
+#define PCIEXBAR_256_BUSES (0 << 1)
+#define PCIEXBAR_ENABLE (1 << 0)
+
+ switch (PCI_MAX_MCFG_BUSES)
+ {
+ case 64:
+ bar_data = PCIEXBAR_64_BUSES | PCIEXBAR_ENABLE;
+ bar_sz = MB(64);
+ break;
+
+ case 128:
+ bar_data = PCIEXBAR_128_BUSES | PCIEXBAR_ENABLE;
+ bar_sz = MB(128);
+ break;
+
+ case 256:
+ bar_data = PCIEXBAR_256_BUSES | PCIEXBAR_ENABLE;
+ bar_sz = MB(256);
+ break;
+
+ default:
+ /* unsupported number of buses specified */
+ BUG();
+ }
+
+ addr_mask = ~(bar_sz - 1);
+
+ for ( i = 0; i < nr_bars; i++ )
+ if ( bars[i].bar_sz < bar_sz )
+ break;
+
+ if ( i != nr_bars )
+ memmove(&bars[i+1], &bars[i], (nr_bars-i) * sizeof(*bars));
+
+ bars[i].is_mem = 1;
+ bars[i].devfn = PCI_MCH_DEVFN;
+ bars[i].bar_reg = PCI_MCH_PCIEXBAR;
+ bars[i].bar_sz = bar_sz;
+ bars[i].addr_mask = addr_mask;
+ bars[i].bar_data = bar_data;
+
+ mmio_total += bar_sz;
+ nr_bars++;
+ }
+
if ( mmio_hole_size )
{
uint64_t max_ram_below_4g = GB(4) - mmio_hole_size;
@@ -473,10 +551,10 @@ void pci_setup(void)
*/
using_64bar = bars[i].is_64bar && bar64_relocate
&& (mmio_total > (mem_resource.max - mem_resource.base));
- bar_data = pci_readl(devfn, bar_reg);
- if ( (bar_data & PCI_BASE_ADDRESS_SPACE) ==
- PCI_BASE_ADDRESS_SPACE_MEMORY )
+ bar_data = bars[i].bar_data;
+
+ if ( bars[i].is_mem )
{
/* Mapping high memory if PCI device is 64 bits bar */
if ( using_64bar ) {
@@ -486,18 +564,15 @@ void pci_setup(void)
if ( !pci_hi_mem_start )
pci_hi_mem_start = high_mem_resource.base;
resource = &high_mem_resource;
- bar_data &= ~PCI_BASE_ADDRESS_MEM_MASK;
}
else {
resource = &mem_resource;
- bar_data &= ~PCI_BASE_ADDRESS_MEM_MASK;
}
mmio_total -= bar_sz;
}
else
{
resource = &io_resource;
- bar_data &= ~PCI_BASE_ADDRESS_IO_MASK;
}
base = (resource->base + bar_sz - 1) & ~(uint64_t)(bar_sz - 1);
@@ -519,7 +594,7 @@ void pci_setup(void)
}
}
- bar_data |= (uint32_t)base;
+ bar_data |= (uint32_t) (base & bars[i].addr_mask);
bar_data_upper = (uint32_t)(base >> 32);
base += bar_sz;
@@ -544,9 +619,7 @@ void pci_setup(void)
/* Now enable the memory or I/O mapping. */
cmd = pci_readw(devfn, PCI_COMMAND);
- if ( (bar_reg == PCI_ROM_ADDRESS) ||
- ((bar_data & PCI_BASE_ADDRESS_SPACE) ==
- PCI_BASE_ADDRESS_SPACE_MEMORY) )
+ if ( bars[i].is_mem )
cmd |= PCI_COMMAND_MEMORY;
else
cmd |= PCI_COMMAND_IO;
diff --git a/tools/firmware/hvmloader/pci_regs.h
b/tools/firmware/hvmloader/pci_regs.h
index ba498b840e..4f1c6d0800 100644
--- a/tools/firmware/hvmloader/pci_regs.h
+++ b/tools/firmware/hvmloader/pci_regs.h
@@ -111,6 +111,8 @@
#define PCI_DEVICE_ID_INTEL_82441 0x1237
#define PCI_DEVICE_ID_INTEL_Q35_MCH 0x29c0
+#define PCI_MCH_PCIEXBAR 0x60
+
#endif /* __HVMLOADER_PCI_REGS_H__ */
--
2.11.0
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxxx
https://lists.xenproject.org/mailman/listinfo/xen-devel
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |