[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Xen-devel] CONFIG_SCRUB_DEBUG=y + arm64 + livepatch = Xen BUG at page_alloc.c:738



Hey,

I've only been able to reproduce this on ARM64 (trying right now ARM32
as well), and not on x86.

If I compile Xen without CONFIG_SCRUB_DEBUG it works great. But if
enable it and try to load a livepatch it blows up in page_alloc.c:738

This is with origin/staging (d0291f3391)

The test-case (livepatch_test.pl) is
http://xenbits.xen.org/gitweb/?p=xentesttools/bootstrap.git;a=blob;f=root_image/debugspace/livepatch_test.pl

The serial log:

oader use UART6
scsysstat_value[8].
clear reset source
last_keypoint0,reboot_type0
secdbg not DCU.
SecDbgVer exit

 xloader chipid is: 0x36600110, start at 481ms.
Build Date: Jun  1 2017, 16:54:45
[clock_init] ++
hi3660 [clk_setup]
[clock_init] --
storage type is UFS
ufs retry: 6 count v_tx:0 v_rx:0
ufs set v_tx:0 v_rx:0
Hikey960[5301] no need avs_init.
ddr ft:0xf20332a3,mode:1 target:4
UceLdOk
ch 0 gt_errfail, STATUS:0x00000060
ch 0 gdst_errfail, STATUS:0x00000040
ch 1 gt_errfail, STATUS:0x00000060
ch 1 gdst_errfail, STATUS:0x00000040
ch 2 gt_errfail, STATUS:0x00000060
ch 2 gdst_errfail, STATUS:0x00000040
ch 3 gt_errfail, STATUS:0x00000060
ch 3 gdst_errfail, STATUS:0x00000040
timeout
timeout
timeout
timeout
density: 
0x0c0c0c0c,0x00000000,0x0c0c0c0c,0x00000000,0x0c0c0c0c,0x00000000,0x0c0c0c0c,0x00000000
 
ddr info 0x00000306 
400M
685M
1067M
C0R,V0x0000002c e:113
C1R,V0x0000002d e:66
C2R,V0x0000002c e:66
C3R,V0x0000002d e:66
C0R,V0x0000002d e:66
C1R,V0x0000002e e:66
C2R,V0x0000002d e:66
C3R,V0x0000002e e:66
C0R,V0x0000002e e:66
C1R,V0x0000002f e:66
C2R,V0x0000002e e:66
C3R,V0x0000002f e:66
C0R,V0x0000002f e:66
C1R,V0x00000030 e:65
C2R,V0x0000002f e:65
C3R,V0x00000030 e:66
1244M
1866M
C0R,V0x00000015 e:66
C2R,V0x00000015 e:66
C0R,V0x00000016 e:66
C1R,V0x00000016 e:66
C2R,V0x00000016 e:66
C3R,V0x00000016 e:66
C0R,V0x00000017 e:66
C1R,V0x00000017 e:66
C2R,V0x00000017 e:66
C3R,V0x00000017 e:66
iomcu_subsys_init
boot_c0 PROFILE 4
NOTICE:  Booting Trusted Firmware
NOTICE:  BL1: v1.4(release):v1.4-8-gca5ba394
NOTICE:  BL1: Built : 21:33:21, Jul 16 2017
NOTICE:  BL1: Booting BL2
NOTICE:  BL2: v1.4(release):v1.4-8-gca5ba394
NOTICE:  BL2: Built : 20:03:29, Jul 15 2017
NOTICE:  BL1: Booting BL31
NOTICE:  BL31: v1.4(release):v1.4-8-gca5ba394
NOTICE:  BL31: Built : 20:03:29, Jul 15 2017
UEFI firmware (version Alpha built at 20:02:58 on Jul 15 2017)
add-symbol-file 
/home/konrad/960/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Core/Dxe/DxeMain/DEBUG/DxeCore.dll
 0xBF251000
Loading DxeCore at 0x00BF250000 EntryPoint=0x00BF251000
add-symbol-file 
/home/konrad/960/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Core/Dxe/DxeMain/DEBUG/DxeCore.dll
 0xBF251000
HOBLIST address in DXE = 0xBF00D018
Memory Allocation 0x00000004 0xBFFE8000 - 0xBFFE8FFF
Memory Allocation 0x00000004 0xBFFE7000 - 0xBFFE7FFF
Memory Allocation 0x00000004 0xBFFE6000 - 0xBFFE6FFF
Memory Allocation 0x00000004 0xBFFE5000 - 0xBFFE5FFF
Memory Allocation 0x00000004 0xBFFE9000 - 0xBFFFFFFF
Memory Allocation 0x00000004 0xBFFD5000 - 0xBFFE4FFF
Memory Allocation 0x00000004 0xBF931000 - 0xBFFD4FFF
Memory Allocation 0x00000004 0xBF28D000 - 0xBF930FFF
Memory Allocation 0x00000004 0xBF250000 - 0xBF28CFFF
Memory Allocation 0x00000003 0xBF250000 - 0xBF28CFFF
FV Hob            0x1AC98000 - 0x1AD87FFF
FV Hob            0xBF28D000 - 0xBF92FD3F
FV2 Hob           0xBF28D000 - 0xBF92FD3F
add-symbol-file 
/home/konrad/960/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/PCD/Dxe/Pcd/DEBUG/PcdDxe.dll
 0xBF192000
Loading driver at 0x000BF191000 EntryPoint=0x000BF192048 PcdDxe.efi
add-symbol-file 
/home/konrad/960/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/ArmPkg/Drivers/CpuDxe/CpuDxe/DEBUG/ArmCpuDxe.dll
 0xBF182000
Loading driver at 0x000BF181000 EntryPoint=0x000BF182048 ArmCpuDxe.efi
add-symbol-file 
/home/konrad/960/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Core/RuntimeDxe/RuntimeDxe/DEBUG/RuntimeDxe.dll
 0xBA190000
Loading driver at 0x000BA180000 EntryPoint=0x000BA190048 RuntimeDxe.efi
add-symbol-file 
/home/konrad/960/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/SecurityStubDxe/SecurityStubDxe/DEBUG/SecurityStubDxe.dll
 0xBF172000
Loading driver at 0x000BF171000 EntryPoint=0x000BF172048 SecurityStubDxe.efi
add-symbol-file 
/home/konrad/960/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/EmbeddedPkg/EmbeddedMonotonicCounter/EmbeddedMonotonicCounter/DEBUG/EmbeddedMonotonicCounter.dll
 0xBA0F0000
Loading driver at 0x000BA0E0000 EntryPoint=0x000BA0F0048 
EmbeddedMonotonicCounter.efi
add-symbol-file 
/home/konrad/960/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/EmbeddedPkg/ResetRuntimeDxe/ResetRuntimeDxe/DEBUG/Reset.dll
 0xBA050000
Loading driver at 0x000BA040000 EntryPoint=0x000BA050048 Reset.efi
add-symbol-file 
/home/konrad/960/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/EmbeddedPkg/RealTimeClockRuntimeDxe/RealTimeClockRuntimeDxe/DEBUG/RealTimeClock.dll
 0xB9FB0000
Loading driver at 0x000B9FA0000 EntryPoint=0x000B9FB0048 RealTimeClock.efi
add-symbol-file 
/home/konrad/960/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/EmbeddedPkg/MetronomeDxe/MetronomeDxe/DEBUG/MetronomeDxe.dll
 0xBF16A000
Loading driver at 0x000BF169000 EntryPoint=0x000BF16A048 MetronomeDxe.efi
add-symbol-file 
/home/konrad/960/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/MdeModulePkg/Universal/SerialDxe/SerialDxe/DEBUG/SerialDxe.dll
 0xBF162000
Loading driver at 0x00......[Bds]Booting UEFI Shell
add-symbol-file 
/home/konrad/960/edk2/Build/HiKey960/DEBUG_GCC5/AARCH64/ShellPkg/Application/Shell/Shell/DEBUG/Shell.dll
 0xB9ACA000
Loading driver at 0x000B9AC9000 EntryPoint=0x000B9ACA000 Shell.efi
UEFI Interactive Shell v2.1
EDK II
UEFI v2.60 (EDK II, 0x00010000)
Mapping table
      FS0: 
Alias(s):HD0h:;BLK15:
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x3)/HD(7,GPT,D3340696-9B95-4C64-8DF6-E6D4548FBA41,0x12100,0x4000)
     BLK0: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x0)
     BLK1: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x1)
     BLK2: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x2)
     BLK3: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x2)/HD(1,GPT,F9F21F00-A8D4-5F0E-9746-594869AEC34E,0x100,0x700)
     BLK4: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x3)
     BLK5: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x3)/HD(1,GPT,697C41E0-7A59-4DFA-A9A6-AA43AC5BE684,0x100,0x100)
    BLK10: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x3)/HD(2,GPT,3F5F8C48-4402-4ACE-9058-30BFEA4FA53F,0x200,0xC00)
    BLK11: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x3)/HD(3,GPT,E2F5E2A9-C9B7-4089-9859-4498F1D3EF7E,0xE00,0x600)
    BLK12: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x3)/HD(4,GPT,DC1A888E-F17C-4964-92D6-F8FCC402ED8B,0x1400,0xC00)
    BLK13: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x3)/HD(5,GPT,10CC3268-05F0-4DB2-AA00-707361427FC8,0x2000,0x10000)
    BLK14: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x3)/HD(6,GPT,5D8481D4-C170-4AA8-9438-8743C73EA8F5,0x12000,0x100)
    BLK16: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x3)/HD(8,GPT,6E53B0BB-FA7E-4206-B607-5AE699E9F066,0x16100,0x1000)
    BLK17: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x3)/HD(9,GPT,F1E126A6-CEEF-45C1-AACE-29F33AC9CF13,0x17100,0x200)
     BLK6: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x3)/HD(10,GPT,C3E50923-FB85-4153-B925-759614D4DFCD,0x17300,0x125000)
     BLK7: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x3)/HD(11,GPT,919D7080-D71A-4AE1-9227-E4585210C837,0x13C300,0x31000)
     BLK8: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x3)/HD(12,GPT,611EAC6B-BC42-4D72-90AC-418569C8E9B8,0x16D300,0x100)
     BLK9: Alias(s):
          VenHw(0D51905B-B77E-452A-A2C0-ECA0CC8D514A,00003BFF0000000000)/UFS(0x0
,0x3)/HD(13,GPT,049B9A32-A36A-483E-AB6F-9EF6644E6D47,0x16D400,0x6047FB)
Press ESC in 5 seconds to skip 
startup.nsh or any other key to continue.Press 
ESC in 4 seconds to skip 
startup.nsh or any other key to continue.Press 
ESC in 3 seconds to skip 
startup.nsh or any other key to continue.Press 
ESC in 2 seconds to skip 
startup.nsh or any other key to continue.Press 
ESC in 1 seconds to skip 
startup.nsh or any other key to continue.
Shell> FS0:
FS0:\> cd EFI\BOOT
FS0:\EFI\BOOT
FS0:\EFI\BOOT\> dir
Directory of: FS0:\EFI\BOOT\
06/30/2017  06:33 <DIR>         1,024  .
06/30/2017  06:33 <DIR>           512  ..
06/30/2017  06:33              26,176  fastboot.efi
08/01/2017  17:19             885,072  xen.efi
07/17/2017  00:40               1,313  grub.cfg
07/17/2017  00:40          20,066,816  Image
07/17/2017  00:40              43,471  Image-dtb
07/17/2017  16:57             847,872  grub.efi
08/01/2017  17:19                 237  xen.cfg
08/01/2017  17:19          16,501,248  Image-4.12
08/01/2017  17:19              35,966  Image-4.12.dtb
07/17/2017  16:57           2,723,192  livepatch.tgz
06/30/2017  06:33             871,424  grub-2.02.efi
08/01/2017  17:19             847,872  grubaa64.efi
         12 File(s)  42,850,659 bytes
          2 Dir(s)
FS0:\EFI\BOOT\> grubaa64.efi
Loading driver at 0x000B9991000 EntryPoint=0x000B9991400
Loading driver at 0x000B9991000 EntryPoint=0x000B9991400 
Welcome to GRUB!

GNU
 GRUB  version 2.03

/----------------------------------------------------------------------------\||||||||||||||||||||||||\----------------------------------------------------------------------------/
     Use the ^ and v keys to select which entry is highlighted.          
      Press enter to boot the selected OS, `e' to edit the commands       
      before booting or `c' for a command-line. ESC to return previous    
      menu.                                                               
 
*Xen                                                      
                   Latest                            
                                          Fastboot                 
                                                                   
                                                                   
                                                                    
                                                                   
                                                                   
                                                                   
                                                                   
                                                                   
                                                                   
                                                                   
                                                                
   The highlighted entry will be executed automatically in 10s. 
                                                                
                                                                        
                                     
Loading
 driver at 0x000B87CC000 EntryPoint=0x000B88798F4
Loading driver at 0x000B87CC000 EntryPoint=0x000B88798F4 
Using modules provided by bootloader in FDT
Xen 4.10-unstable (c/s Wed Aug 16 18:07:27 2017 +0100 git:d0291f3391) EFI loader

 Xen 4.10-unstable
(XEN) Xen version 4.10-unstable (root@) (gcc (Debian 6.3.0-18) 6.3.0 20170516) 
debug=y  Mon Sep 11 23:43:13 UTC 2017
(XEN) Latest ChangeSet: Wed Aug 16 18:07:27 2017 +0100 git:d0291f3391
(XEN) Processor: 410fd034: "ARM Limited", variant: 0x0, part 0xd03, rev 0x4
(XEN) 64-bit Execution:
(XEN)   Processor Features: 0000000000002222 0000000000000000
(XEN)     Exception Levels: EL3:64+32 EL2:64+32 EL1:64+32 EL0:64+32
(XEN)     Extensions: FloatingPoint AdvancedSIMD
(XEN)   Debug Features: 0000000010305106 0000000000000000
(XEN)   Auxiliary Features: 0000000000000000 0000000000000000
(XEN)   Memory Model Features: 0000000000001122 0000000000000000
(XEN)   ISA Features:  0000000000011120 0000000000000000
(XEN) 32-bit Execution:
(XEN)   Processor Features: 00000131:00011011
(XEN)     Instruction Sets: AArch32 A32 Thumb Thumb-2 Jazelle
(XEN)     Extensions: GenericTimer Security
(XEN)   Debug Features: 03010066
(XEN)   Auxiliary Features: 00000000
(XEN)   Memory Model Features: 10201105 40000000 01260000 02102211
(XEN)  ISA Features: 02101110 13112111 21232042 01112131 00011142 00011121
(XEN) Using PSCI-1.0 for SMP bringup
(XEN) SMP: Allowing 8 CPUs
(XEN) Generic Timer IRQ: phys=30 hyp=26 virt=27 Freq: 1920 KHz
(XEN) GICv2 initialization:
(XEN)         gic_dist_addr=00000000e82b1000
(XEN)         gic_cpu_addr=00000000e82b2000
(XEN)         gic_hyp_addr=00000000e82b4000
(XEN)         gic_vcpu_addr=00000000e82b6000
(XEN)         gic_maintenance_irq=25
(XEN) GICv2: 384 lines, 8 cpus, secure (IID 0200143b).
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Allocated console ring of 64 KiB.
(XEN) Bringing up CPU1
(XEN) CPU 1 booted.
(XEN) Bringing up CPU2
(XEN) CPU 2 booted.
(XEN) Bringing up CPU3
(XEN) CPU 3 booted.
(XEN) Bringing up CPU4
(XEN) CPU 4 booted.
(XEN) Bringing up CPU5
(XEN) CPU 5 booted.
(XEN) Bringing up CPU6
(XEN) CPU 6 booted.
(XEN) Bringing up CPU7
(XEN) CPU 7 booted.
(XEN) Brought up 8 CPUs
(XEN) P2M: 40-bit IPA with 40-bit PA and 8-bit VMID
(XEN) P2M: 3 levels with order-1 root, VTCR 0x80023558
(XEN) I/O virtualisation disabled
(XEN) build-id: ce6199b9fac01491da92f8890af4dcf8c85a430e
(XEN) alternatives: Patching with alt table 00000000400c4dd8 -> 00000000400c52ac
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Loading kernel from boot module @ 00000000b88f9000
(XEN) Allocating 1:1 mappings totalling 1500MB for dom0:
(XEN) BANK[0] 0x00000010000000-0x00000018000000 (128MB)
(XEN) BANK[1] 0x00000020000000-0x00000030000000 (256MB)
(XEN) BANK[2] 0x00000038000000-0x0000003c000000 (64MB)
(XEN) BANK[3] 0x00000040000000-0x00000058000000 (384MB)
(XEN) BANK[4] 0x0000008c000000-0x000000b4000000 (640MB)
(XEN) BANK[5] 0x000000b8000000-0x000000b8400000 (4MB)
(XEN) BANK[6] 0x000000ba800000-0x000000bc000000 (24MB)
(XEN) Grant table range: 0x000000bfe00000-0x000000bfe6a000
(XEN) Loading zImage from 00000000b88f9000 to 0000000010080000-000000001103ca00
(XEN) Allocating PPI 16 for event channel interrupt
(XEN) Loading dom0 DTB to 0x0000000017e00000-0x0000000017e08265
(XEN) Initial low memory virq threshold set at 0x4000 pages.
(XEN) Scrubbing Free RAM on 1 nodes using 8 CPUs
(XEN) ...done.
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to 
Xen)
(XEN) Freed 272kB init memory.
(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER4
(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER8
(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER12
(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER16
(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER20
(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER24
(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER28
(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER32
(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER36
(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER40
(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER44
(XEN) d0v0: vGICD: unhandled word write 0xffffffff to ICACTIVER0
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.12.0-linaro-hikey960+ 
(konrad@localhost.localdomain) (gcc version 7.0.1 20170309 (Red Hat Cross 
7.0.1-0.4) (GCC) ) #3 SMP PREEMPT Mon Jul 17 13:26:13 EDT 2017
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] Machine model: HiKey960
[    0.000000] Xen 4.10 support found
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 16 MiB at 0x00000000bb000000
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 
0x0000000000000000-0x00000000bbffffff]
[    0.000000] NUMA: Adding memblock [0x10000000 - 0x17ffffff] on node 0
[    0.000000] NUMA: Adding memblock [0x20000000 - 0x2fffffff] on node 0
[    0.000000] NUMA: Adding memblock [0x38000000 - 0x3bffffff] on node 0
[    0.000000] NUMA: Adding memblock [0x40000000 - 0x57ffffff] on node 0
[    0.000000] NUMA: Adding memblock [0x8c000000 - 0xb3ffffff] on node 0
[    0.000000] NUMA: Adding memblock [0xb8000000 - 0xb83fffff] on node 0
[    0.000000] NUMA: Adding memblock [0xba800000 - 0xbbffffff] on node 0
[    0.000000] NUMA: Initmem setup node 0 [mem 0x10000000-0xbbffffff]
[    0.000000] NUMA: NODE_DATA [mem 0xbafc4100-0xbafc5bff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000010000000-0x00000000bbffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000010000000-0x0000000017ffffff]
[    0.000000]   node   0: [mem 0x0000000020000000-0x000000002fffffff]
[    0.000000]   node   0: [mem 0x0000000038000000-0x000000003bffffff]
[    0.000000]   node   0: [mem 0x0000000040000000-0x0000000057ffffff]
[    0.000000]   node   0: [mem 0x000000008c000000-0x00000000b3ffffff]
[    0.000000]   node   0: [mem 0x00000000b8000000-0x00000000b83fffff]
[    0.000000]   node   0: [mem 0x00000000ba800000-0x00000000bbffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x00000000bbffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv0.2 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS migration not required
[    0.000000] percpu: Embedded 22 pages/cpu @ffff8000baf11000 s59160 r0 d30952 
u90112
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total 
pages: 378000
[    0.000000] Policy zone: DMA
[    0.000000] Kernel command line: console=tty0 console=hvc0 root=/dev/sdd10 
rw efi=noruntime
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Memory: 1452900K/1536000K available (10172K kernel code, 1138K 
rwdata, 3648K rodata, 1088K init, 406K bss, 66716K reserved, 16384K 
cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffff000000000000 - 0xffff000008000000   (   128 
MB)
[    0.000000]     vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000   (129022 
GB)
[    0.000000]       .text : 0xffff000008080000 - 0xffff000008a70000   ( 10176 
KB)
[    0.000000]     .rodata : 0xffff000008a70000 - 0xffff000008e10000   (  3712 
KB)
[    0.000000]       .init : 0xffff000008e10000 - 0xffff000008f20000   (  1088 
KB)
[    0.000000]       .data : 0xffff000008f20000 - 0xffff00000903ca00   (  1139 
KB)
[    0.000000]        .bss : 0xffff00000903ca00 - 0xffff0000090a2334   (   407 
KB)
[    0.000000]     fixed   : 0xffff7dfffe7fd000 - 0xffff7dfffec00000   (  4108 
KB)
[    0.000000]     PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000   (    16 
MB)
[    0.000000]     vmemmap : 0xffff7e0000000000 - 0xffff800000000000   (  2048 
GB maximum)
[    0.000000]               0xffff7e0000400000 - 0xffff7e0002f00000   (    43 
MB actual)
[    0.000000]     memory  : 0xffff800010000000 - 0xffff8000bc000000   (  2752 
MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] arch_timer: cp15 timer(s) running at 1.92MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff 
max_cycles: 0x1c570327e, max_idle_ns: 1763180809505 ns
[    0.000004] sched_clock: 56 bits at 1920kHz, resolution 520ns, wraps every 
4398046510977ns
[    0.000082] clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, 
max_idle_ns: 58334160866034 ns
[    0.000407] Console: colour dummy device 80x25
[    0.000928] console [tty0] enabled
[    0.430205] console [hvc0] enabled
[    0.433732] Calibrating delay loop (skipped), value calculated using timer 
frequency.. 3.84 BogoMIPS (lpj=7680)
[    0.443838] pid_max: default: 32768 minimum: 301
[    0.448565] Security Framework initialized
[    0.452967] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.461000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.468398] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.475005] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.498292] ASID allocator initialised with 65536 entries
[    0.503989] xen:grant_table: Grant tables using version 1 layout
[    0.509923] Grant table initialized
[    0.513486] xen:events: Using FIFO-based ABI
[    0.517844] Xen: initializing cpu0
[    0.534428] EFI services will not be available.
[    0.554913] smp: Bringing up secondary CPUs ...
(XEN) d0v1: vGICD: unhandled word write 0xffffffff to ICACTIVER0
(XEN) d0v2: vGICD: unhandled word write 0xffffffff to ICACTIVER0
(XEN) d0v3: vGICD: unhandled word write 0xffffffff to ICACTIVER0
(XEN) d0v4: vGICD: unhandled word write 0xffffffff to ICACTIVER0
(XEN) d0v5: vGICD: unhandled word write 0xffffffff to ICACTIVER0
(XEN) d0v6: vGICD: unhandled word write 0xffffffff to ICACTIVER0
(XEN) d0v7: vGICD: unhandled word write 0xffffffff to ICACTIVER0
[    0.591511] Detected VIPT I-cache on CPU1
[    0.597168] Xen: initializing cpu1
[    0.597189] CPU1: Booted secondary processor [410fd034]
[    0.627574] Detected VIPT I-cache on CPU2
[    0.633175] Xen: initializing cpu2
[    0.633190] CPU2: Booted secondary processor [410fd034]
[    0.663656] Detected VIPT I-cache on CPU3
[    0.669245] Xen: initializing cpu3
[    0.669258] CPU3: Booted secondary processor [410fd034]
[    0.699756] Detected VIPT I-cache on CPU4
[    0.705362] Xen: initializing cpu4
[    0.705379] CPU4: Booted secondary processor [410fd034]
[    0.735840] Detected VIPT I-cache on CPU5
[    0.741425] Xen: initializing cpu5
[    0.741438] CPU5: Booted secondary processor [410fd034]
[    0.771938] Detected VIPT I-cache on CPU6
[    0.777521] Xen: initializing cpu6
[    0.777534] CPU6: Booted secondary processor [410fd034]
[    0.808032] Detected VIPT I-cache on CPU7
[    0.813620] Xen: initializing cpu7
[    0.813633] CPU7: Booted secondary processor [410fd034]
[    0.813689] smp: Brought up 1 node, 8 CPUs
[    0.907609] SMP: Total of 8 processors activated.
[    0.912379] CPU features: detected feature: 32-bit EL0 Support
[    0.919021] CPU: All CPU(s) started at EL1
[    0.923076] alternatives: patching kernel code
[    0.928225] devtmpfs: initialized
[    0.934788] DMI not present or invalid.
[    0.938780] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, 
max_idle_ns: 7645041785100000 ns
[    0.948485] futex hash table entries: 2048 (order: 6, 262144 bytes)
[    0.955317] pinctrl core: initialized pinctrl subsystem
[    0.961764] NET: Registered protocol family 16
[    0.968109] vdso: 2 pages (1 code @ ffff000008a77000, 1 data @ 
ffff000008f25000)
[    0.975442] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.988221] DMA: preallocated 256 KiB pool for atomic allocations
[    0.994252] xen:swiotlb_xen: Warning: only able to allocate 4 MB for 
software IO TLB
[    1.002486] software IO TLB [mem 0xb0400000-0xb0800000] (4MB) mapped at 
[ffff8000b0400000-ffff8000b07fffff]
[    1.012369] Serial: AMBA PL011 UART driver
[    1.030067] hi3660-mbox e896b000.mailbox: Mailbox enabled
[    1.044616] uart-pl011 ffd74000.serial: could not find pctldev for node 
/soc/pinmux@e896c000/uart3_pmx_func, deferring probe
[    1.055820] uart-pl011 fdf01000.serial: could not find pctldev for node 
/soc/pinmux@e896c000/uart4_pmx_func, deferring probe
[    1.083859] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.091076] ACPI: Interpreter disabled.
[    1.095136] xen:balloon: Initialising balloon driver
[    1.100041] xen_balloon: Initialising balloon driver
[    1.105473] vgaarb: loaded
[    1.108194] SCSI subsystem initialized
[    1.112103] ssp-pl022 ffd68000.spi: could not find pctldev for node 
/soc/pinmux@fff11000/spi2_pmx_func, deferring probe
[    1.122810] ssp-pl022 ff3b3000.spi: could not find pctldev for node 
/soc/pinmux@ff3b6000/spi3_pmx_func, deferring probe
[    1.133743] usbcore: registered new interface driver usbfs
[    1.139191] usbcore: registered new interface driver hub
[    1.144631] usbcore: registered new device driver usb
[    1.149677] tcpc_class_init_1.1.1_G
[    1.153221] TCPC class init OK
[    1.156341] Init Richtek RegMap
[    1.159618] i2c_designware ffd71000.i2c: could not find pctldev for node 
/soc/pinmux@fff11000/i2c0_pmx_func, deferring probe
[    1.170846] i2c_designware ffd72000.i2c: could not find pctldev for node 
/soc/pinmux@fff11000/i2c1_pmx_func, deferring probe
[    1.182112] i2c_designware fdf0b000.i2c: could not find pctldev for node 
/soc/pinmux@fff11000/i2c7_pmx_func, deferring probe
[    1.193630] pps_core: LinuxPPS API ver. 1 registered
[    1.198501] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo 
Giometti <giometti@xxxxxxxx>
[    1.207706] PTP clock support registered
[    1.211749] dmi: Firmware registration failed.
[    1.216360] Advanced Linux Sound Architecture Driver Initialized.
[    1.223048] clocksource: Switched to clocksource arch_sys_counter
[    1.229141] VFS: Disk quotas dquot_6.6.0
[    1.233058] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.240065] pnp: PnP ACPI: disabled
[    1.248314] OF: /soc/thermal-zones/cls0/cooling-maps/map0: could not find 
phandle
[    1.255710] missing cooling_device property
[    1.259947] failed to build thermal zone cls0: -22
[    1.264883] NET: Registered protocol family 2
[    1.269500] TCP established hash table entries: 16384 (order: 5, 131072 
bytes)
[    1.276715] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[    1.283385] TCP: Hash tables configured (established 16384 bind 16384)
[    1.289944] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    1.295984] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    1.302553] NET: Registered protocol family 1
[    1.307185] RPC: Registered named UNIX socket transport module.
[    1.313009] RPC: Registered udp transport module.
[    1.317775] RPC: Registered tcp transport module.
[    1.322544] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.329641] kvm [1]: HYP mode not available
[    1.335727] audit: initializing netlink subsys (disabled)
[    1.341120] audit: type=2000 audit(1.066:1): state=initialized 
audit_enabled=0 res=1
[    1.341273] workingset: timestamp_bits=44 max_order=19 bucket_order=0
[    1.344220] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.344556] NFS: Registering the id_resolver key type
[    1.344572] Key type id_resolver registered
[    1.344573] Key type id_legacy registered
[    1.344579] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.344581] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver 
Registering...
[    1.344695] 9p: Installing v9fs 9p2000 file system support
[    1.347369] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 
247)
[    1.347374] io scheduler noop registered
[    1.347492] io scheduler cfq registered (default)
[    1.347495] io scheduler mq-deadline registered
[    1.347497] io scheduler kyber registered
[    1.350482] pinctrl-single e896c000.pinmux: 124 pins at pa ffff0000094b7000 
size 496
[    1.350560] pinctrl-single ff37e000.pinmux: 6 pins at pa ffff0000094b9000 
size 24
[    1.350621] pinctrl-single ff3b6000.pinmux: 12 pins at pa ffff0000094bb000 
size 48
[    1.350679] pinctrl-single ff3fd000.pinmux: 6 pins at pa ffff0000094bd000 
size 24
[    1.350773] pinctrl-single fff11000.pinmux: 42 pins at pa ffff0000094bf000 
size 168
[    1.350949] pinctrl-single e896c800.pinmux: 128 pins at pa ffff0000094c1800 
size 512
[    1.351003] pinctrl-single ff3b6800.pinmux: 6 pins at pa ffff0000094c3800 
size 24
[    1.351095] pinctrl-single ff3fd800.pinmux: 6 pins at pa ffff0000094c5800 
size 24
[    1.351169] pinctrl-single ff37e800.pinmux: 6 pins at pa ffff0000094c7800 
size 24
[    1.351263] pinctrl-single fff11800.pinmux: 47 pins at pa ffff0000094c9800 
size 188
[    1.352439] pl061_gpio e8a0b000.gpio: PL061 GPIO chip @0x00000000e8a0b000 
registered
[    1.352706] pl061_gpio e8a0c000.gpio: PL061 GPIO chip @0x00000000e8a0c000 
registered
[    1.352936] pl061_gpio e8a0d000.gpio: PL061 GPIO chip @0x00000000e8a0d000 
registered
[    1.353161] pl061_gpio e8a0e000.gpio: PL061 GPIO chip @0x00000000e8a0e000 
registered
[    1.353377] pl061_gpio e8a0f000.gpio: PL061 GPIO chip @0x00000000e8a0f000 
registered
[    1.353600] pl061_gpio e8a10000.gpio: PL061 GPIO chip @0x00000000e8a10000 
registered
[    1.353821] pl061_gpio e8a11000.gpio: PL061 GPIO chip @0x00000000e8a11000 
registered
[    1.354044] pl061_gpio e8a12000.gpio: PL061 GPIO chip @0x00000000e8a12000 
registered
[    1.354270] pl061_gpio e8a13000.gpio: PL061 GPIO chip @0x00000000e8a13000 
registered
[    1.354503] pl061_gpio e8a14000.gpio: PL061 GPIO chip @0x00000000e8a14000 
registered
[    1.354725] pl061_gpio e8a15000.gpio: PL061 GPIO chip @0x00000000e8a15000 
registered
[    1.354950] pl061_gpio e8a16000.gpio: PL061 GPIO chip @0x00000000e8a16000 
registered
[    1.355205] pl061_gpio e8a17000.gpio: PL061 GPIO chip @0x00000000e8a17000 
registered
[    1.355434] pl061_gpio e8a18000.gpio: PL061 GPIO chip @0x00000000e8a18000 
registered
[    1.355661] pl061_gpio e8a19000.gpio: PL061 GPIO chip @0x00000000e8a19000 
registered
[    1.355891] pl061_gpio e8a1a000.gpio: PL061 GPIO chip @0x00000000e8a1a000 
registered
[    1.356117] pl061_gpio e8a1b000.gpio: PL061 GPIO chip @0x00000000e8a1b000 
registered
[    1.356339] pl061_gpio e8a1c000.gpio: PL061 GPIO chip @0x00000000e8a1c000 
registered
[    1.356600] pl061_gpio ff3b4000.gpio: PL061 GPIO chip @0x00000000ff3b4000 
registered
[    1.356830] pl061_gpio ff3b5000.gpio: PL061 GPIO chip @0x00000000ff3b5000 
registered
[    1.357054] pl061_gpio e8a1f000.gpio: PL061 GPIO chip @0x00000000e8a1f000 
registered
[    1.357276] pl061_gpio e8a20000.gpio: PL061 GPIO chip @0x00000000e8a20000 
registered
[    1.357517] pl061_gpio fff0b000.gpio: PL061 GPIO chip @0x00000000fff0b000 
registered
[    1.357777] pl061_gpio fff0c000.gpio: PL061 GPIO chip @0x00000000fff0c000 
registered
[    1.358009] pl061_gpio fff0d000.gpio: PL061 GPIO chip @0x00000000fff0d000 
registered
[    1.358249] pl061_gpio fff0e000.gpio: PL061 GPIO chip @0x00000000fff0e000 
registered
[    1.358487] pl061_gpio fff0f000.gpio: PL061 GPIO chip @0x00000000fff0f000 
registered
[    1.358726] pl061_gpio fff10000.gpio: PL061 GPIO chip @0x00000000fff10000 
registered
[    1.358966] pl061_gpio fff1d000.gpio: PL061 GPIO chip @0x00000000fff1d000 
registered
[    1.362933] xen:xen_evtchn: Event-channel device installed
[    1.366692] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.368220] SuperH (H)SCI(F) driver initialized
[    1.368435] msm_serial: driver initialized
[    1.370657] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    1.376065] loop: module loaded
[    1.376423] [I/GPIO_HUB] gpio_hub_init:gpio hub init status:0
[    1.378107] ufshcd-hi3660 ff3b0000.ufs: ufshcd_populate_vreg: Unable to find 
vdd-hba-supply regulator, assuming enabled
[    1.378112] ufshcd-hi3660 ff3b0000.ufs: ufshcd_populate_vreg: Unable to find 
vcc-supply regulator, assuming enabled
[    1.378116] ufshcd-hi3660 ff3b0000.ufs: ufshcd_populate_vreg: Unable to find 
vccq-supply regulator, assuming enabled
[    1.378118] ufshcd-hi3660 ff3b0000.ufs: ufshcd_populate_vreg: Unable to find 
vccq2-supply regulator, assuming enabled
[    1.402227] scsi host0: ufshcd
[    1.411242] hisi_sas: driver version v1.6
[    1.413033] libphy: Fixed MDIO Bus: probed
[    1.413321] tun: Universal TUN/TAP device driver, 1.6
[    1.413960] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.413961] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.413989] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[    1.413990] igb: Copyright (c) 2007-2014 Intel Corporation.
[    1.414011] igbvf: Intel(R) Gigabit Virtual Function Network Driver - 
version 2.4.0-k
[    1.414013] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    1.414183] sky2: driver version 1.30
[    1.414448] xen_netfront: Initialising Xen virtual ethernet driver
[    1.414504] usbcore: registered new interface driver asix
[    1.414524] usbcore: registered new interface driver ax88179_178a
[    1.414642] VFIO - User Level meta-driver version: 0.3
[    1.415133] [USB3][hisi_dwc3_probe]+
[    1.415211] [USB3][get_phy_param]eye diagram param: 0x1c466e3
[    1.415214] [USB3][get_phy_param]eye diagram host param: 0x1c466e3
[    1.415217] [USB3][get_phy_param]usb3_phy_cr_param: 0xb80
[    1.415218] [USB3][get_phy_param]usb3_phy_host_cr_param: 0x980
[    1.415219] [USB3][get_phy_param]usb3_phy_tx_vboost_lvl: 5
[    1.415234] [USB3][get_resource]this is asic platform (fpga flag 0)
[    1.415236] [USB3][create_attr_file]+
[    1.415280] [USB3][create_attr_file]-
[    1.415283] [USB3][hi3660_usb3phy_init]+
[    1.443178] [USB3][config_femtophy_param]set hs phy param 0x1c466e3 for 
device
[    1.443771] [USB3][config_femtophy_param]set ss phy rx equalization 0xb80
[    1.444619] [USB3][config_femtophy_param]set ss RX_SCOPE_VDCC 0x1
[    1.444621] [USB3][config_femtophy_param]set ss phy tx vboost lvl 0x5
[    1.444623] [USB3][set_hisi_dwc3_power_flag]set hisi_dwc3_power_flag 1
[    1.444624] [USB3][hi3660_usb3phy_init]-
[    1.445250] [dwc3_otg_init]+
[    1.445254] DWC3_OCFG:       0x0
[    1.445255] DWC3_OCTL:       0x40
[    1.445256] DWC3_OEVT:       0x80000000
[    1.445257] DWC3_OEVTEN:     0x0
[    1.445258] DWC3_OSTS:       0x19
[    1.445259] DWC3_BCFG:       0x0
[    1.445260] DWC3_BCEVT:      0x0
[    1.445262] DWC3_BCEVTEN:    0x0
[    1.445263] [dwc3_otg_init]-
[    1.445280] dwc3 ff100000.dwc3: dwc3_host_init if otg, otg will do 
device_add.
[    1.446568] [USB3][hisi_dwc3_wake_lock]usb otg wake lock
[    1.446572] [USB3][hisi_dwc3_probe]init state: OFF
[    1.446574] [USB3][hisi_usb_otg_event]hisi_usb_otg_event in:1
[    1.446576] [USB3][hisi_usb_otg_event]hisi_usb_otg_event in otg:1
[    1.446578] [USB3][hisi_usb_otg_event]event: 1
[    1.446583] [USB3][event_work]+
[    1.446585] [USB3][handle_event][handle_event] type: 1
[    1.446589] [USB3][handle_event]cancel bc_again_work sync:0
[    1.446591] [dwc3_otg_work]+
[    1.446591]  evt = 4
[    1.446593] [dwc3_otg_stop_peripheral]+
[    1.446594] [dwc3_otg_stop_peripheral]-
[    1.446595] [dwc3_otg_work]-
[    1.446596] [USB3][hisi_dwc3_wake_unlock]usb otg wake unlock
[    1.446598] [USB3][handle_event]hisi usb status: DEVICE -> OFF
[    1.446600] [USB3][event_work]-
[    1.446602] [USB3][hisi_dwc3_probe]-
[    1.446876] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.446878] ehci-pci: EHCI PCI platform driver
[    1.446894] ehci-platform: EHCI generic platform driver
[    1.446951] ehci-orion: EHCI orion driver
[    1.446993] ehci-exynos: EHCI EXYNOS driver
[    1.447046] ehci-msm: Qualcomm On-Chip EHCI Host Controller
[    1.447084] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.447091] ohci-pci: OHCI PCI platform driver
[    1.447107] ohci-platform: OHCI generic platform driver
[    1.447149] ohci-exynos: OHCI EXYNOS driver
[    1.447346] usbcore: registered new interface driver usb-storage
[    1.447685] [I/hisi_pd] pd_dpm_init
[    1.447728] [I/hisi_pd] pd_dpm_probe : +++++++++
[    1.447752] [I/hisi_pd] pd_dpm_probe ++++
[    1.447752] 
[    1.447891] rt1711h_init (1.1.8_G): initializing...
[    1.447895] rt1711h node found...
[    1.448339] rtc-pl031 fff04000.rtc: rtc core: registered pl031 as rtc0
[    1.448590] i2c /dev entries driver
[    1.449546] hi3660_thermal fff30000.tsensor: failed to register thermal 
sensor0: -19
[    1.449553] hi3660_thermal fff30000.tsensor: failed to register thermal 
sensor1: -19
[    1.449558] hi3660_thermal fff30000.tsensor: failed to register thermal 
sensor2: -19
[    1.449564] hi3660_thermal fff30000.tsensor: failed to register thermal 
sensor3: -19
[    1.449569] hi3660_thermal fff30000.tsensor: failed to register thermal 
sensor4: -517
[    1.449575] hi3660_thermal fff30000.tsensor: failed to register thermal 
sensor5: -19
[    1.449576] hi3660_thermal fff30000.tsensor: Thermal Sensor Loaded
[    1.449954] cpu cpu0: failed to get clock: -2
[    1.449960] cpufreq-dt: probe of cpufreq-dt failed with error -2
[    1.450106] sdhci: Secure Digital Host Controller Interface driver
[    1.450107] sdhci: Copyright(c) Pierre Ossman
[    1.450246] Synopsys Designware Multimedia Card Interface Driver
[    1.450519] dwmmc_k3 ff37f000.dwmmc1: fifo-depth property not found, using 
value of FIFOTH register as default
[    1.452650] dwmmc_k3 ff37f000.dwmmc1: IDMAC supports 64-bit address mode.
[    1.452731] dwmmc_k3 ff37f000.dwmmc1: Using internal DMA controller.
[    1.452736] dwmmc_k3 ff37f000.dwmmc1: Version ID is 270a
[    1.452764] dwmmc_k3 ff37f000.dwmmc1: DW MMC controller at irq 46,32 bit 
host data width,256 deep fifo
[    1.452866] dwmmc_k3 ff37f000.dwmmc1: Got CD GPIO
[    1.473495] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, 
actual 400000HZ div = 0)
[    1.492176] dwmmc_k3 ff37f000.dwmmc1: 1 slots initialized
[    1.492280] dwmmc_k3 ff3ff000.dwmmc2: fifo-depth property not found, using 
value of FIFOTH register as default
[    1.494404] dwmmc_k3 ff3ff000.dwmmc2: IDMAC supports 64-bit address mode.
[    1.494458] dwmmc_k3 ff3ff000.dwmmc2: Using internal DMA controller.
[    1.494463] dwmmc_k3 ff3ff000.dwmmc2: Version ID is 270a
[    1.494488] dwmmc_k3 ff3ff000.dwmmc2: DW MMC controller at irq 47,32 bit 
host data width,256 deep fifo
[    1.494782] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.495999] ledtrig-cpu: registered to indicate activity on CPUs
[    1.496407] usbcore: registered new interface driver usbhid
[    1.496409] usbhid: USB HID core driver
[    1.497279] NET: Registered protocol family 17
[    1.497342] 9pnet: Installing 9P2000 support
[    1.497375] Key type dns_resolver registered
[    1.497712] registered taskstats version 1
[    1.502398] ffd74000.serial: ttyAMA3 at MMIO 0xffd74000 (irq = 12, base_baud 
= 0) is a PL011 rev2
[    1.504864] fdf01000.serial: ttyAMA4 at MMIO 0xfdf01000 (irq = 13, base_baud 
= 0) is a PL011 rev2
[    1.504927] serial serial0: tty port ttyAMA4 registered
[    1.505165] ssp-pl022 ffd68000.spi: ARM PL022 driver, device ID: 0x00041022
[    1.505194] ssp-pl022 ffd68000.spi: mapped registers from 0x00000000ffd68000 
to ffff0000095cd000
[    1.514009] ssp-pl022 ffd68000.spi: Failed to work in dma mode, work without 
dma!
[    1.514205] ssp-pl022 ff3b3000.spi: ARM PL022 driver, device ID: 0x00041022
[    1.514226] ssp-pl022 ff3b3000.spi: mapped registers from 0x00000000ff3b3000 
to ffff0000095cf000
[    1.514252] ssp-pl022 ff3b3000.spi: Failed to work in dma mode, work without 
dma!
[    1.565265] rt1711_i2c_probe
[    1.565266] I2C functionality : OK...
[    1.671704] ufshcd-hi3660 ff3b0000.ufs: ufshcd_print_pwr_info:[RX, TX]: 
gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate = 0
[    1.691435] rt_parse_dt
[    1.691440] rt1711h_chipID = 0x2171
[    1.691442] regmap_device_register: name = rt1711-4e
[    1.691458]  rt_regmap_rt1711-4e: rt register cache data init
[    1.691462]  rt_regmap_rt1711-4e: cache cata init successfully
[    1.691507] tcpc_device_register register tcpc device (type_c_port0)
[    1.691560] [I/hisi_pd] tcpc_device_register 
register_pd_wake_unlock_notifier OK
[    1.691562] PD Timer number = 37
[    1.691628] tcpci_timer_init : init OK
[    1.691667] pd_parse_pdata
[    1.691673] pd_parse_pdata src pdo data =
[    1.691675] pd_parse_pdata 0: 0x00019064
[    1.691677] pd_parse_pdata snk pdo data =
[    1.691678] pd_parse_pdata 0: 0x000190c8
[    1.691679] pd_parse_pdata 1: 0x0002d0c8
[    1.691681] pd_parse_pdata id vdos data =
[    1.691682] pd_parse_pdata 0: 0xd00029cf
[    1.691683] pd_parse_pdata 1: 0x00000000
[    1.691684] pd_parse_pdata 2: 0x00010000
[    1.691686] dpm_caps: local_dr_power
[    1.691688] dpm_caps: local_dr_data
[    1.691690] dpm_caps: local_ext_power
[    1.691691] dpm_caps: local_usb_comm
[    1.691692] dpm_caps: local_usb_suspend
[    1.691693] dpm_caps: local_high_cap
[    1.691694] dpm_caps: local_give_back
[    1.691696] dpm_caps: local_no_suspend
[    1.691696] dpm_caps: local_vconn_supply
[    1.691698] dpm_caps: attemp_discover_cable_dfp
[    1.691699] dpm_caps: attemp_enter_dp_mode
[    1.691700] dpm_caps: attemp_discover_cable
[    1.691701] dpm_caps: attemp_discover_id
[    1.691702] dpm_caps: pr_reject_as_source
[    1.691703] dpm_caps: pr_reject_as_sink
[    1.691704] dpm_caps: pr_check_gp_source
[    1.691705] dpm_caps: pr_check_gp_sink
[    1.691706] dpm_caps: dr_reject_as_dfp
[    1.691707] dpm_caps: dr_reject_as_ufp
[    1.691708] dpm_caps: snk_prefer_low_voltage
[    1.691709] dpm_caps: snk_ignore_mismatch_current
[    1.691710] dpm_caps = 0xc010c10b
[    1.691712] [I/hisi_pd] PE:pd_core_init
[    1.747592] rt1711_init_alert name = type_c_port0
[    1.747594] rt1711_init_alert gpio # = 291
[    1.747601] GPIO requested...
[    1.747604] rt1711_init_alert : IRQ number = 271
[    1.747605] rt1711_init_alert : irq initialized...
[    1.747659] IRQF_NO_THREAD Test
[    1.971927] [I/hisi_pd] [TCPC-I]SkipAlert:0x0000
[    2.027001] ufs final power mode: gear = 3, lane = 1, pwr = 1, rate = 2
[    2.027006] ufshcd-hi3660 ff3b0000.ufs: set TX_EQUALIZER 3.5db
[    2.184873] ufshcd-hi3660 ff3b0000.ufs: check TX_EQUALIZER DB value lane0 = 
0x1
[    2.184878] ufshcd-hi3660 ff3b0000.ufs: ufshcd_print_pwr_info:[RX, TX]: 
gear=[3, 3], lane[1, 1], pwr[FAST MODE, FAST MODE], rate = 2
[    2.208824] ufshcd-hi3660 ff3b0000.ufs: 
ufshcd_find_max_sup_active_icc_level: Regulator capability was not set, 
actvIccLevel=0
[    2.232164] scsi 0:0:0:49488: scsi_add_lun: correcting incorrect peripheral 
device type 0x0 for W-LUN 0x            c150hN
[    2.232170] scsi 0:0:0:49488: Well-known LUN    SAMSUNG  KLUBG4G1CE-B0B1  
1000 PQ: 0 ANSI: 6
[    2.286397] [I/hisi_pd] TPC-I:typec_init: DRP
[    2.313502] scsi 0:0:0:49456: scsi_add_lun: correcting incorrect peripheral 
device type 0x0 for W-LUN 0x            c130hN
[    2.313506] scsi 0:0:0:49456: Well-known LUN    SAMSUNG  KLUBG4G1CE-B0B1  
1000 PQ: 0 ANSI: 6
[    2.369474] [E/GPIO_HUB] gpio_hub_power_on: gpio hub hub vbus set err
[    2.369477] [E/GPIO_HUB] gpio_hub_change_typec_power: typec power gpio is err
[    2.369480] [USB3][hisi_usb_otg_event]hisi_usb_otg_event in:1
[    2.369481] [USB3][hisi_usb_otg_event]hisi_usb_otg_event in otg:1
[    2.369483] [E/GPIO_HUB] gpio_hub_switch_to_hub: otg_switch_gpio is err
[    2.369485] [USB3][hisi_usb_otg_event]hisi_usb_otg_event in:2
[    2.369486] [USB3][hisi_usb_otg_event]hisi_usb_otg_event in otg:2
[    2.369487] [USB3][hisi_usb_otg_event]event: 2
[    2.369491] [I/hisi_pd] TPC-I:** Unattached.SNK
[    2.369492] [E/hisi_pd] typec_wait_ps_change: 
typec_wait_ps_change!!!+++++++++++
[    2.369493] [E/hisi_pd] typec_wait_ps_change: 
typec_wait_ps_change!!!-----------
[    2.379379] [USB3][event_work]+
[    2.379381] [USB3][handle_event][handle_event] type: 2
[    2.379383] [USB3][set_vbus_power]set port power 1
[    2.379385] [dwc3_otg_work]+
[    2.379385]  evt = 2
[    2.379387] [dwc3_otg_start_host]+
[    2.379581] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    2.379593] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus 
number 1
[    2.379936] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe65 hci version 
0x110 quirks 0x00010010
[    2.379958] xhci-hcd xhci-hcd.0.auto: irq 285, io mem 0xff100000
[    2.380235] hub 1-0:1.0: USB hub found
[    2.380248] hub 1-0:1.0: 1 port detected
[    2.380344] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    2.380350] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus 
number 2
[    2.380383] usb usb2: We don't know the algorithms for LPM for this host, 
disabling LPM.
[    2.380595] hub 2-0:1.0: USB hub found
[    2.380605] hub 2-0:1.0: 1 port detected
[    2.380683] [dwc3_otg_start_host]-
[    2.380684] [dwc3_otg_work]-
[    2.380686] [USB3][hisi_dwc3_wake_lock]usb otg wake lock
[    2.380690] [USB3][handle_event]hisi usb_status: OFF -> HOST
[    2.380691] [USB3][event_work]-
[    2.392980] scsi 0:0:0:49476: scsi_add_lun: correcting incorrect peripheral 
device type 0x0 for W-LUN 0x            c144hN
[    2.392984] scsi 0:0:0:49476: Well-known LUN    SAMSUNG  KLUBG4G1CE-B0B1  
1000 PQ: 0 ANSI: 6
[    2.417946] tcpc_device_irq_enable : tcpc irq enable OK!
[    2.417947] rt1711_i2c_probe probe OK!
[    2.418638] dwmmc_k3 ff3ff000.dwmmc2: fifo-depth property not found, using 
value of FIFOTH register as default
[    2.420746] dwmmc_k3 ff3ff000.dwmmc2: IDMAC supports 64-bit address mode.
[    2.420792] dwmmc_k3 ff3ff000.dwmmc2: Using internal DMA controller.
[    2.420798] dwmmc_k3 ff3ff000.dwmmc2: Version ID is 270a
[    2.420817] dwmmc_k3 ff3ff000.dwmmc2: DW MMC controller at irq 47,32 bit 
host data width,128 deep fifo
[    2.420894] mmc_host mmc1: card is non-removable.
[    2.451576] scsi 0:0:0:0: Direct-Access     SAMSUNG  KLUBG4G1CE-B0B1  1000 
PQ: 0 ANSI: 6
[    2.525143] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, 
actual 400000HZ div = 0)
[    2.533551] scsi 0:0:0:1: Direct-Access     SAMSUNG  KLUBG4G1CE-B0B1  1000 
PQ: 0 ANSI: 6
[    2.567071] dwmmc_k3 ff3ff000.dwmmc2: 1 slots initialized
[    2.567547] input: keys as /devices/platform/keys/input/input0
[    2.573857] rtc-pl031 fff04000.rtc: setting system clock to 1970-02-08 
20:51:27 UTC (3358287)
[    2.592159] ALSA device list:
[    2.592161]   No soundcards found.
[    2.602644] sd 0:0:0:0: [sda] 1024 4096-byte logical blocks: (4.19 MB/4.00 
MiB)
[    2.602647] sd 0:0:0:0: [sda] 16384-byte physical blocks
[    2.602695] scsi 0:0:0:2: Direct-Access     SAMSUNG  KLUBG4G1CE-B0B1  1000 
PQ: 0 ANSI: 6
[    2.602802] sd 0:0:0:0: [sda] Write Protect is off
[    2.609529] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, 
supports DPO and FUA
[    2.628220] dwmmc_k3 ff3ff000.dwmmc2: card claims to support voltages below 
defined range
[    2.629268] [I/hisi_pd] TPC-I:[CC_Alert] 5/0
[    2.629271] [I/hisi_pd] TPC-I:** AttachWait.SNK
[    2.642039] scsi 0:0:0:3: Direct-Access     SAMSUNG  KLUBG4G1CE-B0B1  1000 
PQ: 0 ANSI: 6
[    2.646232] sd 0:0:0:1: [sdb] 1024 4096-byte logical blocks: (4.19 MB/4.00 
MiB)
[    2.646236] sd 0:0:0:1: [sdb] 16384-byte physical blocks
[    2.651872] sd 0:0:0:1: [sdb] Write Protect is off
[    2.662612] sd 0:0:0:1: [sdb] Write cache: enabled, read cache: enabled, 
supports DPO and FUA
[    2.681772] sd 0:0:0:2: [sdc] 2048 4096-byte logical blocks: (8.39 MB/8.00 
MiB)
[    2.681775] sd 0:0:0:2: [sdc] 16384-byte physical blocks
[    2.686452] sd 0:0:0:2: [sdc] Write Protect is off
[    2.697207] sd 0:0:0:2: [sdc] Write cache: enabled, read cache: enabled, 
supports DPO and FUA
[    2.707230] sd 0:0:0:3: [sdd] 7805952 4096-byte logical blocks: (32.0 
GB/29.8 GiB)
[    2.707233] sd 0:0:0:3: [sdd] 16384-byte physical blocks
[    2.710747] sd 0:0:0:3: [sdd] Write Protect is off
[    2.726366] sd 0:0:0:3: [sdd] Write cache: enabled, read cache: enabled, 
supports DPO and FUA
[    2.749311] [I/hisi_pd] TPC-I:[CC_Change] 5/0
[    2.749314] [E/hisi_pd] typec_wait_ps_change: 
typec_wait_ps_change!!!+++++++++++
[    2.749316] [E/hisi_pd] typec_wait_ps_change: 
typec_wait_ps_change!!!-----------
[    2.749319] [E/GPIO_HUB] gpio_hub_power_off: gpio hub hub vbus no power set 
err
[    2.749321] [E/GPIO_HUB] gpio_hub_change_typec_power: typec power gpio is err
[    2.749323] [USB3][hisi_usb_otg_event]hisi_usb_otg_event in:3
[    2.749325] [USB3][hisi_usb_otg_event]hisi_usb_otg_event in otg:3
[    2.749327] [USB3][hisi_usb_otg_event]event: 3
[    2.749335] [E/GPIO_HUB] gpio_hub_switch_to_typec: otg_switch_gpio is err
[    2.749336] [USB3][hisi_usb_otg_event]hisi_usb_otg_event in:0
[    2.749338] [USB3][hisi_usb_otg_event]hisi_usb_otg_event in otg:0
[    2.749339] [USB3][hisi_usb_otg_event]event: 0
[    2.749340] [USB3][hisi_usb_otg_event]schedule event_work wait:0]
[    2.749342] [I/hisi_pd] TPC-I:** Attached.SNK
[    2.749343] [E/hisi_pd] typec_wait_ps_change: 
typec_wait_ps_change!!!+++++++++++
[    2.749344] [E/hisi_pd] typec_wait_ps_change: 
typec_wait_ps_change!!!-----------
[    2.758682] [USB3][event_work]+
[    2.758684] [USB3][handle_event][handle_event] type: 3
[    2.758686] [USB3][set_vbus_power]set port power 0
[    2.758689] [I/hisi_pd] pd_dpm_report_bc12 : PD_WAKE_UNLOCK
[    2.758692] [I/hisi_pd] pd_dpm_report_bc12 : event (4)
[    2.758694] [E/hisi_pd] pd_dpm_vbus_notifier_call: 
pd_dpm_vbus_notifier_call!!!,++++
[    2.758695] [dwc3_otg_work]+
[    2.758695]  evt = 1
[    2.758697] [dwc3_otg_stop_host]+
[    2.758746] xhci-hcd xhci-hcd.0.auto: remove, state 4
[    2.758757] usb usb2: USB disconnect, device number 1
[    2.759116] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[    2.759127] xhci-hcd xhci-hcd.0.auto: remove, state 4
[    2.759136] usb usb1: USB disconnect, device number 1
[    2.759568] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[    2.759606] [dwc3_otg_stop_host]-
[    2.759607] [dwc3_otg_work]-
[    2.759610] [USB3][hisi_dwc3_wake_unlock]usb otg wake unlock
[    2.759613] [USB3][handle_event]hiusb_status: HOST -> OFF
[    2.759614] [USB3][handle_event][handle_event] type: 0
[    2.775514] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.796705] random: fast init done
[    2.856527] [E/hisi_pd] pd_dpm_handle_pe_event:!!!,event=3,+++
[    2.856531] [I/hisi_pd] pd_dpm_report_pd_sink_vbus : Sink 5000 mV, 500 mA
[    2.856532] [E/hisi_pd] pd_dpm_vbus_notifier_call: 
pd_dpm_vbus_notifier_call!!!,++++
[    2.856535] [I/hisi_pd] TPC-I:Attached-> SINK
[    2.856536] [E/hisi_pd] pd_dpm_handle_pe_event:!!!,event=7,+++
[    2.856539] [I/hisi_pd] pd_dpm_set_typec_state = 2
[    2.856541] [I/hisi_pd] pd_dpm_set_cc_orientation cc_orientation =0
[    2.856547] [I/hisi_pd] [TCPC-I]usb_port_attached
[    2.856567] [I/hisi_pd] pd_dpm_report_device_attach 
[    2.881198] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 
25000000Hz, actual 25000000HZ div = 0)
[    2.914234] sd 0:0:0:1: [sdb] Attached SCSI disk
[    2.931666] Alternate GPT is invalid, using primary GPT.
[    2.931677]  sdc: sdc1
[    3.058176]  sdd: sdd1 sdd2 sdd3 sdd4 sdd5 sdd6 sdd7 sdd8 sdd9 sdd10 sdd11 
sdd12 sdd13
[    3.063763] sd 0:0:0:2: [sdc] Attached SCSI disk
[    3.083061] [USB3][detect_charger_type]DCD done
[    3.111050] [USB3][detect_charger_type]Primary Detection done
[    3.111052] [USB3][detect_charger_type]Secondary Detection done
[    3.131563] sd 0:0:0:3: [sdd] Attached SCSI disk
[    3.139046] [USB3][detect_charger_type]type: 0
[    3.139050] [I/hisi_pd] pd_dpm_report_bc12 : event (0)
[    3.139052] [E/hisi_pd] pd_dpm_vbus_notifier_call: 
pd_dpm_vbus_notifier_call!!!,++++
[    3.139056] [USB3][handle_event]schedule ret:1, run bc_again_work 8000ms 
later
[    3.139058] [dwc3_otg_work]+
[    3.139058]  evt = 3
[    3.139060] [dwc3_otg_start_peripheral]+
[    3.139064] [dwc3_otg_start_peripheral]-
[    3.139065] [dwc3_otg_work]-
[    3.139067] [USB3][hisi_dwc3_wake_lock]usb otg wake lock
[    3.139070] [USB3][handle_event]hisi usb status: OFF -> DEVICE
[    3.139072] [USB3][event_work]-
[    3.617106] [E/hisi_pd] pd_dpm_handle_pe_event:!!!,event=6,+++
[    3.617108] [I/hisi_pd] pd_dpm_handle_pe_event  unkonw event 
[    3.673202] [E/hisi_pd] pd_dpm_handle_pe_event:!!!,event=5,+++
[    3.673204] Pending event is same --> ignore this event 2
[    3.700365] [E/hisi_pd] pd_dpm_handle_pe_event:!!!,event=3,+++
[    3.708177] mmc1: new SDIO card at address 0001
[    3.758715] wl18xx_driver wl18xx.0.auto: Direct firmware load for 
ti-connectivity/wl18xx-conf.bin failed with error -2
[    3.758719] wlcore: ERROR could not get configuration binary 
ti-connectivity/wl18xx-conf.bin: -2
[    3.758721] wlcore: WARNING falling back to default config
[    4.331372] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
[    4.483612] wlcore: loaded
[    4.520856] EXT4-fs (sdd10): couldn't mount as ext3 due to feature 
incompatibilities
[    4.545654] EXT4-fs (sdd10): recovery complete
[    4.550413] EXT4-fs (sdd10): mounted filesystem with ordered data mode. 
Opts: (null)
[    4.558110] VFS: Mounted root (ext4 filesystem) on device 8:58.
[    4.564315] devtmpfs: mounted
[    4.567513] Freeing unused kernel memory: 1088K
[    4.626079] systemd[1]: System time before build time, advancing clock.

Welcome to Debian GNU/Linux 9 (stretch)!

NetworkManager-wait-online.service: Cannot add dependency job, ignoring: Unit 
NetworkManager-wait-online.service is masked.
[  OK  ] Started Dispatch Password Requests to Console Directory 
Watch.
[  OK  ] Listening on Journal Socket.
[  OK  ] Listening on Syslog Socket.
[  OK  ] Created slice System Slice.
         Starting Remount Root and Kernel File Systems...
         Starting Load Kernel Modules...
[  OK  ] Created slice system-serial\x2dgetty.slice.
[  OK  ] Created slice system-getty.slice.
[  OK  ] Listening on Journal Audit Socket.
         Mounting Huge Pages File System...
[  OK  ] Listening on Network Service Netlink Socket.
[  OK  ] Reached target Remote File Systems.
[  OK  ] Listening on udev Kernel Socket.
         Starting Set the console keyboard layout...
[  OK  ] Created slice User and Session Slice.
[  OK  ] Reached target Slices.
[  OK  ] Listening on Journal Socket (/dev/log).
         Starting Nameserver information manager...
[  OK  ] Listening on udev Control Socket.
         Starting Journal Service...
[  OK  ] Started Forward Password Requests to Wall Directory Watch.
[  OK  ] Reached target Encrypted Volumes.
         Starting Create Static Device Nodes in /dev...
[  OK  ] Listening on /dev/initctl Compatibility Named Pipe.
         Mounting POSIX Message Queue File System...
         Mounting Debug File System...
[  OK  ] Mounted POSIX Message Queue File System.
[  OK  ] Mounted Debug File System.
[  OK  ] Mounted Huge Pages File System.
[  OK  ] Started Journal Service.
[  OK  ] Started Remount Root and Kernel File Systems.
[  OK  ] Started Load Kernel Modules.
[  OK  ] Started Create Static Device Nodes in /dev.
[  OK  ] Started Nameserver information manager.
         Starting udev Kernel Device Manager...
         Starting Apply Kernel Variables...
         Mounting Configuration File System...
         Starting udev Coldplug all Devices...
         Starting Load/Save Random Seed...
         Starting Flush Journal to Persistent Storage...
[  OK  ] Mounted Configuration File System.
[  OK  ] Started Apply Kernel Variables.
[  OK  ] Started Set the console keyboard layout.
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started udev Kernel Device Manager.
[    5.054294] systemd-journald[1509]: Received request to flush runtime 
journal from PID 1
[  OK  ] Reached target Local File Systems (Pre).
         Starting Network Service...
[  OK  ] Started Flush Journal to Persistent Storage.
[FAILED] Failed to start Network Service.
See 'systemctl status systemd-networkd.service' for details.
[  OK  ] Started udev Coldplug all Devices.
[  OK  ] Stopped Network Service.
         Starting Network Service...
[FAILED] Failed to start Network Service.
See 'systemctl status systemd-networkd.service' for details.
[  OK  ] Found device /dev/hvc0.
[  OK  ] Found device KLUBG4G1CE-B0B1 userdata.
[  OK  ] Found device KLUBG4G1CE-B0B1 vendor.
         Activating swap /dev/sdd11...
         Mounting /home...
[  OK  [    5.272875] A] dding 802812k swStopped Network Service.ap 
on /dev/sdd11
.  Priority:-1 extents:1 across:802812k SS
[    5.282079] EXT4-fs (sdd13): recovery complete
[    5.282086] EXT4-fs (sdd13): mounted filesystem with ordered data mode. 
Opts: (null)
         Starting Network Service...
[  OK  ] Mounted /home.
[  OK  ] Activated swap /dev/sdd11.
[  OK  ] Reached target Swap.
[  OK  ] Reached target Local File Systems.
         Starting Raise network interfaces...
         Starting Create Volatile Files and Directories...
         Starting Set console font and keymap...
[FAILED] Failed to start Network Service.
See 'systemctl status systemd-networkd.service' for details.
[  OK  ] Started Create Volatile Files and Directories.
[  OK  ] Started Set console font and keymap.
[  OK  ] Stopped Network Service.
         Starting Network Service...
         Starting Network Time Synchronization...
         Starting Update UTMP about System Boot/Shutdown...
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[FAILED] Failed to start Network Service.
See 'systemctl status systemd-networkd.service' for details.
[  OK  ] Stopped Network Service.
         Starting Network Service...
[  OK  ] Started Raise network interfaces.
[FAILED] Failed to start Network Service.
See 'systemctl status systemd-networkd.service' for details.
[  OK  ] Stopped Network Service.
[FAILED] Failed to start Network Service.
See 'systemctl status systemd-networkd.service' for details.
[  OK  ] Started Network Time Synchronization.
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Reached target System Initialization.
[  OK  ] Listening on ACPID Listen Socket.
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Started ACPI Events Check.
[  OK  ] Reached target Paths.
[  OK  ] Listening on OpenBSD Secure Shell server socket.
[  OK  ] Reached target Sockets.
[  OK  ] Reached target Basic System.
         Starting System Logging Service...
[  OK  ] Started Regular background program processing daemon.
         Starting Provide limited super user privileges to specific users...
         Starting LSB: Load kernel modules needed to enable cpufreq scaling...
         Starting Restore /etc/resolv.conf i…fore the ppp link was shut down...
         Starting RealtimeKit Scheduling Policy Service...
[  OK  ] Started ACPI event daemon.
         Starting Login Service...
[  OK  ] Started D-Bus System Message Bus.
[  OK  ] Started RealtimeKit Scheduling Policy Service.
         Starting WPA supplicant...
         Starting Network Manager...
         Starting Modem Manager...
         Starting Initialize hardware monitoring sensors...
[  OK  ] Started System Logging Service.
[  OK  ] Started Provide limited super user privileges to specific 
users.
[  OK  ] Started Restore /etc/resolv.conf if…before the ppp link was 
shut down.
[  OK  ] Started Initialize hardware monitoring sensors.
[  OK  ] Started WPA supplicant.
[  OK  ] Started LSB: Load kernel modules needed to enable cpufreq 
scaling.
[  OK  ] Started Login Service.
         Starting Authorization Manager...
         Starting LSB: set CPUFreq kernel parameters...
[  OK  ] Started LSB: set CPUFreq kernel parameters.
[  OK  ] Started Authorization Manager.
[  OK  ] Started Network Manager.
         Starting Network Manager Script Dispatcher Service...
[  OK  ] Reached target Network.
         Starting Network Name Resolution...
         Starting Permit User Sessions...
[  OK  ] Reached target Network is Online.
         Starting LSB: Advanced IEEE 802.11 management daemon...
[  OK  ] Started Daily apt download activities.
[  OK  ] Started Daily apt upgrade and clean activities.
[  OK  ] Reached target Timers.
         Starting LSB: exim Mail Transport Agent...
         Starting /etc/rc.local Compatibility...
[  OK  ] Started Permit User Sessions.
[  OK  ] Started LSB: Advanced IEEE 802.11 management daemon.
[  OK  ] Started /etc/rc.local Compatibility.
[  OK  ] Started Modem Manager.
[  OK  ] Started Network Manager Script Dispatcher Service.
         Starting Hostname Service...
[  OK  ] Started Getty on tty1.
[  OK  ] Started Serial Getty on hvc0.
[  OK  ] Reached target Login Prompts.
[  OK  ] Started Hostname Service.
[  OK  ] Started Network Name Resolution.
[    6.333185] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, 
actual 400000HZ div = 0)
[    6.380747] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 
25000000Hz, actual 25000000HZ div = 0)
[  OK  ] Started LSB: exim Mail Transport Agent.
[  OK  ] Reached target Multi-User System.
[  OK  ] Reached target Graphical Interface.
         Starting Update UTMP about System Runlevel Changes...
[  OK  ] Started Update UTMP about System Runlevel Changes.

Debian GNU/Linux 9 linaro-developer hvc0

linaro-developer login: root (automatic login)

Last login: Mon Sep 11 23:44:40 UTC 2017 on hvc0
Linux linaro-developer 4.12.0-linaro-hikey960+ #3 SMP PREEMPT Mon Jul 17 
13:26:13 EDT 2017 aarch64

HiKey 960
root@linaro-developer:~# [    6.821000] wlcore: PHY firmware version: Rev 
8.2.0.0.236
[    6.928961] wlcore: firmware booted (Rev 8.9.0.0.69)
[    6.953637] wlcore: down
[    7.085147] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, 
actual 400000HZ div = 0)
[    7.129006] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 
25000000Hz, actual 25000000HZ div = 0)
[    7.538572] wlcore: PHY firmware version: Rev 8.2.0.0.236
[    7.648995] wlcore: firmware booted (Rev 8.9.0.0.69)
[    8.607090] [E/hisi_pd] pd_dpm_handle_pe_event:!!!,event=6,+++
[    8.612841] [I/hisi_pd] pd_dpm_handle_pe_event  unkonw event 
[    8.668303] [E/hisi_pd] pd_dpm_handle_pe_event:!!!,event=5,+++
[    8.674037] Pending event is same --> ignore this event 2
[    8.702064] [E/hisi_pd] pd_dpm_handle_pe_event:!!!,event=3,+++
[   11.247098] [USB3][bc_again_work]+
[   11.250406] [USB3][bc_again_work]charger_type is  SDP, start bc_again_work
[   11.257373] [dwc3_otg_work]+
[   11.257373]  evt = 4
[   11.257383] [dwc3_otg_stop_peripheral]+
[   11.266467] [dwc3_otg_stop_peripheral]-
[   11.270372] [dwc3_otg_work]-

root@linaro-developer:~# [   11.583056] [USB3][detect_charger_type]DCD done
[   11.615057] [USB3][detect_charger_type]Primary Detection done
[   11.620710] [USB3][detect_charger_type]Secondary Detection done
[   11.651059] [USB3][detect_charger_type]type: 0
[   11.655411] [I/hisi_pd] pd_dpm_report_bc12 : event (0)
[   11.660631] [E/hisi_pd] pd_dpm_vbus_notifier_call: 
pd_dpm_vbus_notifier_call!!!,++++
[   11.668444] [dwc3_otg_work]+
[   11.668444]  evt = 3
[   11.668446] [dwc3_otg_start_peripheral]+
[   11.677610] [dwc3_otg_start_peripheral]-
[   11.681615] [dwc3_otg_work]-
[   11.684557] [USB3][bc_again_work]-
[   11.926347] wlcore: down
[   12.001049] wlan0: authenticate with 70:3a:cb:23:d7:dc
[   12.016926] wlan0: send auth to 70:3a:cb:23:d7:dc (try 1/3)
[   12.055569] wlan0: authenticated
[   12.063081] wlan0: associate with 70:3a:cb:23:d7:dc (try 1/3)
[   12.073148] wlan0: RX AssocResp from 70:3a:cb:23:d7:dc (capab=0x11 status=0 
aid=2)
[   12.092685] wlan0: associated
[   12.323140] wlcore: Association completed.

root@linaro-developer:~# xl inf[   13.613355] [E/hisi_pd] 
pd_dpm_handle_pe_event:!!!,event=6,+++
[   13.619110] [I/hisi_pd] pd_dpm_handle_pe_event  unkonw event o
[   13.675194] [E/hisi_pd] pd_dpm_handle_pe_event:!!!,event=5,+++
[   13.680929] Pending event is same --> ignore this event 2
[   13.708391] [E/hisi_pd] pd_dpm_handle_pe_event:!!!,event=3,+++

host                   : linaro-developer
release                : 4.12.0-linaro-hikey960+
version                : #3 SMP PREEMPT Mon Jul 17 13:26:13 EDT 2017
machine                : aarch64
nr_cpus                : 8
max_cpu_id             : 7
nr_nodes               : 1
cores_per_socket       : 1
threads_per_core       : 1
cpu_mhz                : 1
hw_caps                : 
00000000:00000000:00000000:00000000:00000000:00000000:00000000:00000000
virt_caps              :
total_memory           : 2262
free_memory            : 712
sharing_freed_memory   : 0
sharing_used_memory    : 0
outstanding_claims     : 0
free_cpus              : 0
xen_major              : 4
xen_minor              : 10
xen_extra              : -unstable
xen_version            : 4.10-unstable
xen_caps               : xen-3.0-aarch64 xen-3.0-armv7l 
xen_scheduler          : credit
xen_pagesize           : 4096
platform_params        : virt_start=0x200000
xen_changeset          : Wed Aug 16 18:07:27 2017 +0100 git:d0291f3391
xen_commandline        : loglvl=all console=dtuart dtuart=/soc/serial@fff32000 
efi=no-rs dom0_mem=1500M
cc_compiler            : gcc (Debian 6.3.0-18) 6.3.0 20170516
cc_compile_by          : root
cc_compile_domain      : 
cc_compile_date        : Mon Sep 11 23:43:13 UTC 2017
build_id               : ce6199b9fac01491da92f8890af4dcf8c85a430e
xend_config_format     : 4
root@linaro-developer:~# /root/l[   18.414184] [I/hisi_pd] PE:TYPE-C Only 
Charger!
[   18.418716] [E/hisi_pd] pd_dpm_handle_pe_event:!!!,event=3,+++
[   18.424621] [I/hisi_pd] pd_dpm_report_pd_sinki_vbus : Sink 5000 mV, 500 mA
[   18.431557] [E/hisi_pd] pd_dpm_vbus_notifier_call: 
pd_dpm_vbus_notifier_call!!!,++++
[   18.439363] [E/hisi_pd] pd_dpm_handle_pe_event:!!!,event=8,+++
vepatch_test.pl
Have 37 test-cases
Executing: '(set -e;cd /root/test/livepatch;xen-livepatch list)' .. ID          
                           | status
----------------------------------------+------------
Executing: '(set -e;cd /root/test/livepatch;xen-livepatch list)' .. ID          
                           | status
----------------------------------------+------------
Executing: '(set -e;cd /root/test/livepatch;xl info)' ..host                   
: linaro-developer
release                : 4.12.0-linaro-hikey960+
version                : #3 SMP PREEMPT Mon Jul 17 13:26:13 EDT 2017
machine                : aarch64
nr_cpus                : 8
max_cpu_id             : 7
nr_nodes               : 1
cores_per_socket       : 1
threads_per_core       : 1
cpu_mhz                : 1
hw_caps                : 
00000000:00000000:00000000:00000000:00000000:00000000:00000000:00000000
virt_caps              :
total_memory           : 2262
free_memory            : 712
sharing_freed_memory   : 0
sharing_used_memory    : 0
outstanding_claims     : 0
free_cpus              : 0
xen_major              : 4
xen_minor              : 10
xen_extra              : -unstable
xen_version            : 4.10-unstable
xen_caps               : xen-3.0-aarch64 xen-3.0-armv7l 
xen_scheduler          : credit
xen_pagesize           : 4096
platform_params        : virt_start=0x200000
xen_changeset          : Wed Aug 16 18:07:27 2017 +0100 git:d0291f3391
xen_commandline        : loglvl=all console=dtuart dtuart=/soc/serial@fff32000 
efi=no-rs dom0_mem=1500M
cc_compiler            : gcc (Debian 6.3.0-18) 6.3.0 20170516
cc_compile_by          : root
cc_compile_domain      : 
cc_compile_date        : Mon Sep 11 23:43:13 UTC 2017
build_id               : ce6199b9fac01491da92f8890af4dcf8c85a430e
xend_config_format     : 4
Executing: '(set -e;cd /root/test/livepatch;xl info)' ..host                   
: linaro-developer
release                : 4.12.0-linaro-hikey960+
version                : #3 SMP PREEMPT Mon Jul 17 13:26:13 EDT 2017
machine                : aarch64
nr_cpus                : 8
max_cpu_id             : 7
nr_nodes               : 1
cores_per_socket       : 1
threads_per_core       : 1
cpu_mhz                : 1
hw_caps                : 
00000000:00000000:00000000:00000000:00000000:00000000:00000000:00000000
virt_caps              :
total_memory           : 2262
free_memory            : 712
sharing_freed_memory   : 0
sharing_used_memory    : 0
outstanding_claims     : 0
free_cpus              : 0
xen_major              : 4
xen_minor              : 10
xen_extra              : -unstable
xen_version            : 4.10-unstable
xen_caps               : xen-3.0-aarch64 xen-3.0-armv7l 
xen_scheduler          : credit
xen_pagesize           : 4096
platform_params        : virt_start=0x200000
xen_changeset          : Wed Aug 16 18:07:27 2017 +0100 git:d0291f3391
xen_commandline        : loglvl=all console=dtuart dtuart=/soc/serial@fff32000 
efi=no-rs dom0_mem=1500M
cc_compiler            : gcc (Debian 6.3.0-18) 6.3.0 20170516
cc_compile_by          : root
cc_compile_domain      : 
cc_compile_date        : Mon Sep 11 23:43:13 UTC 2017
build_id               : ce6199b9fac01491da92f8890af4dcf8c85a430e
xend_config_format     : 4
Executing: '(set -e;cd /root/test/livepatch;xen-livepatch revert 
xen_hello_world)' ..Failed to get status of xen_hello_world.
Error 2: No such file or directory
Executing: '(set -e;cd /root/test/livepatch;xen-livepatch load 
xen_hello_world.livepatch)' ..Uploading xen_hello_world.livepatch... (XEN) Xen 
BUG at page_alloc.c:738
(XEN) ----[ Xen-4.10-unstable  arm64  debug=y   Not tainted ]----
(XEN) CPU:    0
(XEN) PC:     000000000021fcb4 page_alloc.c#alloc_heap_pages+0x5c8/0x6e0
(XEN) LR:     000000000021fb08
(XEN) SP:     00008000bf1d79f0
(XEN) CPSR:   00000249 MODE:64-bit EL2h (Hypervisor, handler)
(XEN)      X0: 09010219ffdb2387  X1: 0000800000000000  X2: 00008000b98b3000
(XEN)      X3: 00000000b98b3000  X4: ffffffffffffffff  X5: 0000000000000000
(XEN)      X6: 0000000000000014  X7: 00000000002e3e48  X8: 00000000000017c0
(XEN)      X9: 000000000007ffff X10: 00000000002e3da8 X11: 0000000000000000
(XEN)     X12: 0000000000000000 X13: 0000000802896680 X14: 00004c9800000000
(XEN)     X15: 000000000000051b X16: 0000000000000023 X17: 0000ffffa559d088
(XEN)     X18: 0000000000000000 X19: 0000000802896728 X20: 000000000007ffff
(XEN)     X21: 0000000000000000 X22: 0000000802896728 X23: 0000000802896728
(XEN)     X24: 0000000802896760 X25: 0000000000000000 X26: 0000000000000000
(XEN)     X27: c2c2c2c2c2c2c2c2 X28: 6db6db6db6db6db7  FP: 00008000bf1d79f0
(XEN) 
(XEN)   VTCR_EL2: 80023558
(XEN)  VTTBR_EL2: 00010000bff30000
(XEN) 
(XEN)  SCTLR_EL2: 30cd183d
(XEN)    HCR_EL2: 000000008038663f
(XEN)  TTBR0_EL2: 00000000bff0e000
(XEN) 
(XEN)    ESR_EL2: f2000001
(XEN)  HPFAR_EL2: 0000000000e82b10
(XEN)    FAR_EL2: ffff000008000f00
(XEN) 
(XEN) Xen stack trace from sp=00008000bf1d79f0:
(XEN)    00008000bf1d7a70 000000000021fe70 0000000000000000 0000000000000000
(XEN)    0000000000000000 000000000029ae18 0000000000000024 6db6db6db6db6db7
(XEN)    fffffff800000000 0000000000000001 0000000000000005 00000000ffffffff
(XEN)    0000000000000005 000000000029ae18 00008000bf1d7ab0 000000000023bca4
(XEN)    00008000bf1d7ab0 000000000023bce4 0000000000000000 0000000000000003
(XEN)    00008000b87c3f20 000000000029ae18 000000000029b000 000000000000001d
(XEN)    00008000bf1d7b00 000000000023be20 0000000000000024 0000000000000000
(XEN)    00008000bfe9e440 0000000040015000 00008000b87c3e80 00008000bfe9e468
(XEN)    0000000000000003 00008000bfe9e488 00008000bf1d7b10 0000000000217524
(XEN)    00008000bf1d7c70 00000000002367a4 0000000000000000 0000000000000000
(XEN)    0000ffffa5757004 0000000000322c98 00000000002991a0 00000000002e3000
(XEN)    0000000000000124 000000000000001d ffff000008a72000 ffff8000a7478d00
(XEN)    000000000031c020 00000000000000a0 0000000000000000 0000000000295bb8
(XEN)    0000000000000000 ffff8000a7478d00 00008000bf1d7bc0 00008000bfe9e570
(XEN)    0000000000005720 0000000040015000 00008000bfe9e600 00008000bfe9ea90
(XEN)    0000000000000039 00008000bfe9ea20 00008000bfe9ea40 0000000000000021
(XEN)    6c6c65685f6e6578 00646c726f775f6f 00008000bf1d7c70 0000000000235ee8
(XEN)    00008000bf1d7eb0 00008000bf1d7f30 0000ffffa5757004 0000000020000145
(XEN)    000000005a000ea1 0000fffffdebef70 0000000000000124 000000000000001d
(XEN)    00008000bf1d7c70 0000000000235f58 0000000000000000 0000ffffa5757004
(XEN)    00008000bf1d7dd0 000000000025d728 00008000bf1d7eb0 00008000bf1d7f30
(XEN)    000000005a000ea1 0000000020000145 000000005a000ea1 0000fffffdebef70
(XEN)    0000000000000124 000000000000001d ffff000008a72000 ffff8000a7478d00
(XEN)    0000000000321c08 0000000000254ae8 00008000bf1d7d50 0000000000251b14
(XEN)    00008000bf1dbcd0 00008000bf1de000 00008000bf1dee70 0000000000000004
(XEN)    00008000bf1dbce8 00000000000000a0 0000000000000136 0000000000001d4c
(XEN)    00008000bf1d7d50 0000000000251c18 0000000000000000 0000000f0000001b
(XEN)    0000000000000000 0000ffffa577a004 0000000000000010 0000000000005720
(XEN)    0000ffffa5758004 0000000000000000 ffffffffffffffff ffff000000000000
(XEN)    0000000000000000 0000000000100000 4010040140100401 4010000000000000
(XEN)    4010040140100401 4010040140100401 0000aaaadb240010 0000aaaadb22eb50
(XEN)    00008000bf1d7e20 000000000025fd1c 0000000000000ea1 00008000bf1d7eb0
(XEN)    00008000bf1d7e70 0000000000252124 0000000000321c00 0000000000007003
(XEN)    00008000bf1d7fb8 00000000200001c5 ffff8000a74dbd50 000000000026739c
(XEN)    ffff8000b01b95e8 ffff8000ac8a3400 00008000bf1d7fb8 0000000020000145
(XEN)    000000005a000ea1 0000fffffdebef70 0000000000000124 000000000000001d
(XEN)    ffff000008a72000 ffff8000a7478d00 ffff8000b01fb800 0000000000000000
(XEN)    ffff8000baf14db0 000000000026746c ffff8000b01fb800 0000000000007003
(XEN)    0000ffffa5757004 0000000000000000 0000000000000000 0000000000000000
(XEN)    0000000000000000 0000000000000000 ffff8000a74dbe00 0000000000000000
(XEN) Xen call trace:
(XEN)    [<000000000021fcb4>] page_alloc.c#alloc_heap_pages+0x5c8/0x6e0 (PC)
(XEN)    [<000000000021fb08>] page_alloc.c#alloc_heap_pages+0x41c/0x6e0 (LR)
(XEN)    [<000000000021fe70>] alloc_domheap_pages+0xa4/0x150
(XEN)    [<000000000023bce4>] vmap.c#vmalloc_type+0xa4/0x1b8
(XEN)    [<000000000023be20>] vmalloc_xen+0x10/0x18
(XEN)    [<0000000000217524>] livepatch_op+0x2c0/0x14a0
(XEN)    [<00000000002367a4>] do_sysctl+0x8ec/0xa30
(XEN)    [<000000000025d728>] traps.c#do_trap_hypercall+0x6c/0x164
(XEN)    [<000000000025fd1c>] do_trap_guest_sync+0xd50/0x1bd4
(XEN)    [<000000000026739c>] entry.o#guest_sync+0x9c/0xcc
(XEN) 
(XEN) 
(XEN) ****************************************
(XEN) Panic on CPU 0:
(XEN) Xen BUG at page_alloc.c:738
(XEN) ****************************************
(XEN) 
(XEN) Reboot in five seconds...

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
https://lists.xen.org/xen-devel

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.