[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-devel] [PATCH v8 1/5] x86: add simple udelay calibration



Hi, Lu

At 05/05/2017 08:50 PM, Boris Ostrovsky wrote:
On 05/05/2017 01:41 AM, Lu Baolu wrote:
Hi,

On 05/03/2017 06:38 AM, Boris Ostrovsky wrote:
On 03/21/2017 04:01 AM, Lu Baolu wrote:
Add a simple udelay calibration in x86 architecture-specific
boot-time initializations. This will get a workable estimate
for loops_per_jiffy. Hence, udelay() could be used after this
initialization.
This breaks Xen PV guests since at this point, and until
x86_init.paging.pagetable_init() which is when pvclock_vcpu_time_info is
mapped, they cannot access pvclock.

Is it reasonable to do this before tsc_init() is called? (The failure
has nothing to do with tsc_init(), really --- it's just that it is
called late enough that Xen PV guests get properly initialized.) If it
is, would it be possible to move simple_udelay_calibration() after
x86_init.paging.pagetable_init()?
This is currently only used for bare metal. How about by-pass it
for Xen PV guests?

It is fixed this for Xen PV guests now (in the sense that we don't crash
anymore) but my question is still whether this is not too early. Besides
tsc_init() (which might not be important here), at the time when
simple_udelay_calibration() is invoked we haven't yet called:
* kvmclock_init(), which sets calibration routines for KVM
* init_hypervisor_platform(), which sets calibration routines for vmware
and Xen HVM
* x86_init.paging.pagetable_init(), which sets calibration routines for
Xen PV


I guess these may have been missed.

Do you have any comments about these?

-boris



Best regards,
Lu Baolu

-boris


Cc: Ingo Molnar <mingo@xxxxxxxxxx>
Cc: x86@xxxxxxxxxx
Signed-off-by: Lu Baolu <baolu.lu@xxxxxxxxxxxxxxx>
---
 arch/x86/kernel/setup.c | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/x86/kernel/setup.c b/arch/x86/kernel/setup.c
index 4bf0c89..e70204e 100644
--- a/arch/x86/kernel/setup.c
+++ b/arch/x86/kernel/setup.c
@@ -837,6 +837,26 @@ dump_kernel_offset(struct notifier_block *self, unsigned 
long v, void *p)
        return 0;
 }

+static void __init simple_udelay_calibration(void)
+{
+       unsigned int tsc_khz, cpu_khz;
+       unsigned long lpj;
+
+       if (!boot_cpu_has(X86_FEATURE_TSC))
+               return;


if it returns here,  can we use udelay() correctly like before?

Thanks,

        dou.

+
+       cpu_khz = x86_platform.calibrate_cpu();
+       tsc_khz = x86_platform.calibrate_tsc();
+
+       tsc_khz = tsc_khz ? : cpu_khz;
+       if (!tsc_khz)
+               return;
+
+       lpj = tsc_khz * 1000;
+       do_div(lpj, HZ);
+       loops_per_jiffy = lpj;
+}
+
 /*
  * Determine if we were loaded by an EFI loader.  If so, then we have also been
  * passed the efi memmap, systab, etc., so we should use these data structures
@@ -985,6 +1005,8 @@ void __init setup_arch(char **cmdline_p)
         */
        x86_configure_nx();

+       simple_udelay_calibration();
+
        parse_early_param();

 #ifdef CONFIG_MEMORY_HOTPLUG







_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
https://lists.xen.org/xen-devel

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.