[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-devel] [PATCH 11/12 v3] xen/arm: vpl011: Add a pl011 uart DT node in the guest device tree



Hi Bhupinder,

On 10/05/17 15:35, Bhupinder Thakur wrote:
The SBSA uart node format is as specified in
Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt and given below:

ARM SBSA defined generic UART
------------------------------
This UART uses a subset of the PL011 registers and consequently lives
in the PL011 driver. It's baudrate and other communication parameters
cannot be adjusted at runtime, so it lacks a clock specifier here.

Required properties:
- compatible: must be "arm,sbsa-uart"
- reg: exactly one register range
- interrupts: exactly one interrupt specifier
- current-speed: the (fixed) baud rate set by the firmware

Signed-off-by: Bhupinder Thakur <bhupinder.thakur@xxxxxxxxxx>
---

Changes since v2:
- Currently device discovery using ACPI is not supported.
- Dropped the reviewed-by tag by Stefano as there were some IRQ related changes
  done later.

 tools/libxl/libxl_arm.c | 53 +++++++++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 51 insertions(+), 2 deletions(-)

diff --git a/tools/libxl/libxl_arm.c b/tools/libxl/libxl_arm.c
index d842d88..f88ef0d 100644
--- a/tools/libxl/libxl_arm.c
+++ b/tools/libxl/libxl_arm.c
@@ -44,10 +44,23 @@ int libxl__arch_domain_prepare_config(libxl__gc *gc,
     uint32_t nr_spis = 0;
     unsigned int i;

+    /*
+     * If pl011 vuart is enabled then increment the nr_spis to allow allocation
+     * of SPI VIRQ for pl011.
+     */
+    if (d_config->b_info.vuart)
+        nr_spis += (GUEST_VPL011_SPI - 32) + 1;
+
     for (i = 0; i < d_config->b_info.num_irqs; i++) {
         uint32_t irq = d_config->b_info.irqs[i];
         uint32_t spi;

+        if (d_config->b_info.vuart && (irq == GUEST_VPL011_SPI))
+        {
+            LOG(ERROR, "Physical IRQ %u conflicting with pl011 SPI\n", irq);
+            return ERROR_FAIL;
+        }
+
         if (irq < 32)
             continue;

@@ -130,9 +143,10 @@ static struct arch_info {
     const char *guest_type;
     const char *timer_compat;
     const char *cpu_compat;
+    const char *uart_compat;
 } arch_info[] = {
-    {"xen-3.0-armv7l",  "arm,armv7-timer", "arm,cortex-a15" },
-    {"xen-3.0-aarch64", "arm,armv8-timer", "arm,armv8" },
+    {"xen-3.0-armv7l",  "arm,armv7-timer", "arm,cortex-a15", "arm,sbsa-uart" },
+    {"xen-3.0-aarch64", "arm,armv8-timer", "arm,armv8", "arm,sbsa-uart" },
 };

 /*
@@ -590,6 +604,38 @@ static int make_hypervisor_node(libxl__gc *gc, void *fdt,
     return 0;
 }

+static int make_vpl011_uart_node(libxl__gc *gc, void *fdt,
+                                 const struct arch_info *ainfo,
+                                 struct xc_dom_image *dom)
+{
+    int res;
+    gic_interrupt intr;
+
+    res = fdt_begin_node(fdt, "sbsa-pl011");
+    if (res) return res;
+
+    res = fdt_property_compat(gc, fdt, 1, ainfo->uart_compat);
+    if (res) return res;
+
+    res = fdt_property_regs(gc, fdt, ROOT_ADDRESS_CELLS, ROOT_SIZE_CELLS,
+                            1,
+                            GUEST_PL011_BASE, GUEST_PL011_SIZE);
+    if (res) return res;
+
+    set_interrupt(intr, GUEST_VPL011_SPI, 0xf, DT_IRQ_TYPE_LEVEL_HIGH);
+
+    res = fdt_property_interrupts(gc, fdt, &intr, 1);
+    if (res) return res;
+
+    /* Use a default baud rate of 115200. */
+    fdt_property_u32(fdt, "current-speed", 115200);

Again, please explain in the commit message why 115200. How this is going to affect the driver?

+
+    res = fdt_end_node(fdt);
+    if (res) return res;
+
+    return 0;
+}
+
 static const struct arch_info *get_arch_info(libxl__gc *gc,
                                              const struct xc_dom_image *dom)
 {
@@ -889,6 +935,9 @@ next_resize:
         FDT( make_timer_node(gc, fdt, ainfo, xc_config->clock_frequency) );
         FDT( make_hypervisor_node(gc, fdt, vers) );

+        if (info->vuart)
+            FDT( make_vpl011_uart_node(gc, fdt, ainfo, dom) );
+
         if (pfdt)
             FDT( copy_partial_fdt(gc, fdt, pfdt) );



Cheers,

--
Julien Grall

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
https://lists.xen.org/xen-devel

 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.