Re: [Xen-devel] [PATCH] x86/vpmu: Add get/put_vpmu() and VPMU_ENABLED

["Jan Beulich" <JBeulich@xxxxxxxx>]

>>> On 16.02.17 at 15:59, <boris.ostrovsky@xxxxxxxxxx> wrote:
> vpmu_enabled() (used by hvm/pv_cpuid() to properly report 0xa leaf
> for Intel processors) is based on the value of VPMU_CONTEXT_ALLOCATED
> bit. This is problematic:
> * For HVM guests VPMU context is allocated lazily, during the first
>   access to VPMU MSRs. Since the leaf is typically queried before guest
>   attempts to read or write the MSRs it is likely that CPUID will report
>   no PMU support
> * For PV guests the context is allocated eagerly but only in responce to
>   guest's XENPMU_init hypercall. There is a chance that the guest will
>   try to read CPUID before making this hypercall.
> 
> This patch introduces VPMU_ENABLED flag which is set (subject to vpmu_mode
> constraints) during VCPU initialization for both PV and HVM guests. Since
> this flag is expected to be managed together with vpmu_count, get/put_vpmu()
> are added to simplify code.

I think VPMU_ENABLED is misleading, as it may as well mean the state
after the guest did enable it. How about VPMU_AVAILABLE?

> @@ -509,15 +498,63 @@ void vpmu_initialise(struct vcpu *v)
>      if ( ret )
>          printk(XENLOG_G_WARNING "VPMU: Initialization failed for %pv\n", v);
>  
> -    /* Intel needs to initialize VPMU ops even if VPMU is not in use */
> -    if ( !is_priv_vpmu &&
> -         (ret || (vpmu_mode == XENPMU_MODE_OFF) ||
> -          (vpmu_mode == XENPMU_MODE_ALL)) )
> +    return ret;
> +}
> +
> +static void get_vpmu(struct vcpu *v)
> +{
> +    spin_lock(&vpmu_lock);
> +
> +    /*
> +     * Count active VPMUs so that we won't try to change vpmu_mode while
> +     * they are in use.
> +     * vpmu_mode can be safely updated while dom0's VPMUs are active and
> +     * so we don't need to include it in the count.
> +     */
> +    if ( !is_hardware_domain(v->domain) &&
> +        (vpmu_mode & (XENPMU_MODE_SELF | XENPMU_MODE_HV)) )
> +    {
> +        vpmu_count++;
> +        vpmu_set(vcpu_vpmu(v), VPMU_ENABLED);
> +    }
> +    else if ( is_hardware_domain(v->domain) &&
> +              (vpmu_mode != XENPMU_MODE_OFF) )
> +        vpmu_set(vcpu_vpmu(v), VPMU_ENABLED);
> +
> +    spin_unlock(&vpmu_lock);
> +}
> +
> +static void put_vpmu(struct vcpu *v)
> +{
> +    if ( !vpmu_is_set(vcpu_vpmu(v), VPMU_ENABLED) )
> +        return;
> +
> +    spin_lock(&vpmu_lock);
> +
> +    if ( !is_hardware_domain(v->domain) &&
> +         (vpmu_mode & (XENPMU_MODE_SELF | XENPMU_MODE_HV)) )
>      {
> -        spin_lock(&vpmu_lock);
>          vpmu_count--;
> -        spin_unlock(&vpmu_lock);
> +        vpmu_reset(vcpu_vpmu(v), VPMU_ENABLED);

I think you need to re-check VPMU_ENABLED after acquiring the lock,
in order to avoid decrementing vpmu_count twice in case of a race.

Also this new model basically limits the opportunity to change the
mode to the case where no guest at all is running, iiuc. Previously
this would have been possible with any number of guests running,
as long as none of them actually used the vPMU.

>      }
> +    else if ( is_hardware_domain(v->domain) &&
> +              (vpmu_mode != XENPMU_MODE_OFF) )
> +        vpmu_reset(vcpu_vpmu(v), VPMU_ENABLED);
> +
> +    spin_unlock(&vpmu_lock);
> +}
> +
> +

No double blank lines please.

Jan


_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
https://lists.xen.org/xen-devel