[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Xen-devel] [PATCH v8 4/4] iommu: add rmrr Xen command line option for extra rmrrs



From: Elena Ufimtseva <elena.ufimtseva@xxxxxxxxxx>

On some platforms RMRR regions may be not specified
in ACPI and thus will not be mapped 1:1 in dom0. This
causes IO Page Faults and prevents dom0 from booting
in PVH mode.
New Xen command line option rmrr allows to specify
such devices and memory regions. These regions are added
to the list of RMRR defined in ACPI if the device
is present in system. As a result, additional RMRRs will
be mapped 1:1 in dom0 with correct permissions.

Mentioned above problems were discovered during PVH work with
ThinkCentre M and Dell 5600T. No official documentation
was found so far in regards to what devices and why cause this.
Experiments show that ThinkCentre M USB devices with enabled
debug port generate DMA read transactions to the regions of
memory marked reserved in host e820 map.
For Dell 5600T the device and faulting addresses are not found yet.

For detailed history of the discussion please check following threads:
http://lists.Xen.org/archives/html/xen-devel/2015-02/msg01724.html
http://lists.Xen.org/archives/html/xen-devel/2015-01/msg02513.html

Format for rmrr Xen command line option:
rmrr=start<-end>=[s1]bdf1[,[s1]bdf2[,...]];start<-end>=[s2]bdf1[,[s2]bdf2[,...]]
If grub2 used and multiple ranges are specified, ';' should be
quoted/escaped, refer to grub2 manual for more information.

Signed-off-by: Elena Ufimtseva <elena.ufimtseva@xxxxxxxxxx>
---
 docs/misc/xen-command-line.markdown |  13 ++
 xen/drivers/passthrough/vtd/dmar.c  | 246 ++++++++++++++++++++++++++++++++----
 2 files changed, 236 insertions(+), 23 deletions(-)

diff --git a/docs/misc/xen-command-line.markdown 
b/docs/misc/xen-command-line.markdown
index aa684c0..f307f3d 100644
--- a/docs/misc/xen-command-line.markdown
+++ b/docs/misc/xen-command-line.markdown
@@ -1197,6 +1197,19 @@ Specify the host reboot method.
 'efi' instructs Xen to reboot using the EFI reboot call (in EFI mode by
  default it will use that method first).
 
+### rmrr
+> '= 
start<-end>=[s1]bdf1[,[s1]bdf2[,...]];start<-end>=[s2]bdf1[,[s2]bdf2[,...]]
+
+Define RMRR units that are missing from ACPI table along with device they
+belong to and use them for 1:1 mapping. End addresses can be omitted and one
+page will be mapped. The ranges are inclusive when start and end are specified.
+If segment of the first device is not specified, segment zero will be used.
+If other segments are not specified, first device segment will be used.
+If a segment is specified for other than the first device and it does not match
+the one specified for the first one, an error will be reported.
+Note: grub2 requires to escape or use quotations if special characters are 
used,
+namely ';', refer to the grub2 documentation if multiple ranges are specified.
+
 ### ro-hpet
 > `= <boolean>`
 
diff --git a/xen/drivers/passthrough/vtd/dmar.c 
b/xen/drivers/passthrough/vtd/dmar.c
index a8e1e5d..fa659a9 100644
--- a/xen/drivers/passthrough/vtd/dmar.c
+++ b/xen/drivers/passthrough/vtd/dmar.c
@@ -42,6 +42,8 @@
 #define MIN_SCOPE_LEN (sizeof(struct acpi_dmar_device_scope) + \
                        sizeof(struct acpi_dmar_pci_path))
 
+#define PRI_RMRR(s,e) "[%lx-%lx]"
+
 LIST_HEAD_READ_MOSTLY(acpi_drhd_units);
 LIST_HEAD_READ_MOSTLY(acpi_rmrr_units);
 static LIST_HEAD_READ_MOSTLY(acpi_atsr_units);
@@ -425,7 +427,7 @@ static int __init acpi_parse_dev_scope(
         default:
             if ( iommu_verbose )
                 printk(XENLOG_WARNING VTDPREFIX "Unknown scope type %#x\n",
-                       acpi_scope->entry_type);
+                acpi_scope->entry_type);
             start += acpi_scope->length;
             continue;
         }
@@ -479,8 +481,7 @@ acpi_parse_one_drhd(struct acpi_dmar_header *header)
     INIT_LIST_HEAD(&dmaru->ioapic_list);
     INIT_LIST_HEAD(&dmaru->hpet_list);
     if ( iommu_verbose )
-        dprintk(VTDPREFIX, "  dmaru->address = %"PRIx64"\n",
-                dmaru->address);
+        dprintk(VTDPREFIX, "  dmaru->address = %"PRIx64"\n", dmaru->address);
 
     ret = iommu_alloc(dmaru);
     if ( ret )
@@ -541,8 +542,8 @@ acpi_parse_one_drhd(struct acpi_dmar_header *header)
             if ( !pci_device_detect(drhd->segment, b, d, f) )
             {
                 dprintk(XENLOG_WARNING VTDPREFIX,
-                        " Non-existent device (%04x:%02x:%02x.%u) is reported"
-                        " in this DRHD's scope!\n", drhd->segment, b, d, f);
+                        " Non-existent device (%04x:%02x:%02x.%u) is reported 
in this DRHD's scope!\n",
+                        drhd->segment, b, d, f);
                 invalid_cnt++;
             }
         }
@@ -553,8 +554,8 @@ acpi_parse_one_drhd(struct acpi_dmar_header *header)
                  invalid_cnt == dmaru->scope.devices_cnt )
             {
                 dprintk(XENLOG_WARNING VTDPREFIX,
-                    "  Workaround BIOS bug: ignore the DRHD due to all "
-                    "devices under its scope are not PCI discoverable!\n");
+                        "  Workaround BIOS bug: ignore the DRHD due to all "
+                        "devices under its scope are not PCI discoverable!\n");
 
                 scope_devices_free(&dmaru->scope);
                 iommu_free(dmaru);
@@ -563,10 +564,10 @@ acpi_parse_one_drhd(struct acpi_dmar_header *header)
             else
             {
                 dprintk(XENLOG_WARNING VTDPREFIX,
-                    "  The DRHD is invalid due to there are devices under "
-                    "its scope are not PCI discoverable! Pls try option "
-                    "iommu=force or iommu=workaround_bios_bug if you "
-                    "really want VT-d\n");
+                        "  The DRHD is invalid due to there are devices under "
+                        "its scope are not PCI discoverable! Pls try option "
+                        "iommu=force or iommu=workaround_bios_bug if you "
+                        "really want VT-d\n");
                 ret = -EINVAL;
             }
         }
@@ -604,8 +605,7 @@ static int register_one_rmrr(struct acpi_rmrr_unit *rmrru)
         if ( pci_device_detect(rmrru->segment, b, d, f) == 0 )
         {
             dprintk(XENLOG_WARNING VTDPREFIX,
-                    " Non-existent device (%04x:%02x:%02x.%u) is reported"
-                    " in RMRR (%"PRIx64", %"PRIx64")'s scope!\n",
+                    " Non-existent device (%04x:%02x:%02x.%u) is reported in 
RMRR "PRI_RMRR(s,e)"'s scope!\n",
                     rmrru->segment, b, d, f,
                     rmrru->base_address, rmrru->end_address);
             ignore = 1;
@@ -620,16 +620,16 @@ static int register_one_rmrr(struct acpi_rmrr_unit *rmrru)
     if ( ignore )
     {
         dprintk(XENLOG_WARNING VTDPREFIX,
-                "  Ignore the RMRR (%"PRIx64", %"PRIx64") due to "
+                "  Ignore the RMRR "PRI_RMRR(s,e)" due to "
                 "devices under its scope are not PCI discoverable!\n",
-            rmrru->base_address, rmrru->end_address);
+                rmrru->base_address, rmrru->end_address);
         scope_devices_free(&rmrru->scope);
         xfree(rmrru);
     }
     else if ( rmrru->base_address > rmrru->end_address )
     {
         dprintk(XENLOG_WARNING VTDPREFIX,
-                "  The RMRR (%"PRIx64", %"PRIx64") is incorrect!\n",
+                "  The RMRR "PRI_RMRR(s,e)" is incorrect!\n",
                 rmrru->base_address, rmrru->end_address);
         scope_devices_free(&rmrru->scope);
         xfree(rmrru);
@@ -639,7 +639,7 @@ static int register_one_rmrr(struct acpi_rmrr_unit *rmrru)
     {
         if ( iommu_verbose )
             dprintk(VTDPREFIX,
-                    "  RMRR region: base_addr %"PRIx64" end_address 
%"PRIx64"\n",
+                    "  RMRR region: "PRI_RMRR(s,e)"\n",
                     rmrru->base_address, rmrru->end_address);
         acpi_register_rmrr_unit(rmrru);
     }
@@ -664,7 +664,7 @@ acpi_parse_one_rmrr(struct acpi_dmar_header *header)
        if ( base_addr <= rmrru->end_address && rmrru->base_address <= end_addr 
)
        {
            printk(XENLOG_ERR VTDPREFIX
-                  "Overlapping RMRRs [%"PRIx64",%"PRIx64"] and 
[%"PRIx64",%"PRIx64"]\n",
+                  "Overlapping RMRRs "PRI_RMRR(s,e)" and "PRI_RMRR(s,e)"\n",
                   rmrru->base_address, rmrru->end_address,
                   base_addr, end_addr);
            return -EEXIST;
@@ -678,8 +678,7 @@ acpi_parse_one_rmrr(struct acpi_dmar_header *header)
          (!page_is_ram_type(paddr_to_pfn(end_addr), RAM_TYPE_RESERVED)) )
     {
         dprintk(XENLOG_WARNING VTDPREFIX,
-                "  RMRR address range not in reserved memory "
-                "base = %"PRIx64" end = %"PRIx64"; "
+                "  RMRR address range "PRI_RMRR(s,e)" not in reserved memory; "
                 "iommu_inclusive_mapping=1 parameter may be needed.\n",
                 base_addr, end_addr);
     }
@@ -779,8 +778,7 @@ acpi_parse_one_rhsa(struct acpi_dmar_header *header)
     list_add_tail(&rhsau->list, &acpi_rhsa_units);
     if ( iommu_verbose )
         dprintk(VTDPREFIX,
-                "  rhsau->address: %"PRIx64
-                " rhsau->proximity_domain: %"PRIx32"\n",
+                "  rhsau->address: %"PRIx64" rhsau->proximity_domain: 
%"PRIx32"\n",
                 rhsau->address, rhsau->proximity_domain);
 
     return ret;
@@ -869,6 +867,140 @@ out:
     return ret;
 }
 
+#define MAX_EXTRA_RMRR_PAGES 16
+#define MAX_EXTRA_RMRR 10
+
+/* RMRR units derived from command line rmrr option */
+#define MAX_EXTRA_RMRR_DEV 20
+struct extra_rmrr_unit {
+    struct list_head list;
+    unsigned long base_pfn, end_pfn;
+    unsigned int dev_count;
+    u32    sbdf[MAX_EXTRA_RMRR_DEV];
+};
+static __initdata unsigned int nr_rmrr;
+static struct __initdata extra_rmrr_unit extra_rmrr_units[MAX_EXTRA_RMRR];
+
+/* Macro for RMRR inclusive range formatting */
+
+static void __init add_extra_rmrr(void)
+{
+    struct acpi_rmrr_unit *acpi_rmrr;
+    struct acpi_rmrr_unit *rmrru;
+    unsigned int dev, seg, i, j;
+    unsigned long pfn;
+
+    for ( i = 0; i < nr_rmrr; i++ )
+    {
+        if ( extra_rmrr_units[i].base_pfn > extra_rmrr_units[i].end_pfn )
+        {
+            printk(XENLOG_ERR VTDPREFIX
+                   "Invalid RMRR Range "PRI_RMRR(s,e)"\n",
+                   extra_rmrr_units[i].base_pfn, extra_rmrr_units[i].end_pfn);
+            continue;
+        }
+
+        if ( extra_rmrr_units[i].end_pfn - extra_rmrr_units[i].base_pfn >=
+             MAX_EXTRA_RMRR_PAGES )
+        {
+            printk(XENLOG_ERR VTDPREFIX
+                   "RMRR range "PRI_RMRR(s,e)" exceeds 
"__stringify(MAX_EXTRA_RMRR_PAGES)" pages\n",
+                   extra_rmrr_units[i].base_pfn, extra_rmrr_units[i].end_pfn);
+            continue;
+        }
+
+        for ( j = 0; j < nr_rmrr; j++ )
+        {
+            if ( i != j &&
+                 extra_rmrr_units[i].base_pfn <= extra_rmrr_units[j].end_pfn &&
+                 extra_rmrr_units[j].base_pfn <= extra_rmrr_units[i].end_pfn )
+            {
+                printk(XENLOG_ERR VTDPREFIX
+                      "Overlapping RMRRs "PRI_RMRR(s,e)" and 
"PRI_RMRR(s,e)"\n",
+                      extra_rmrr_units[i].base_pfn, 
extra_rmrr_units[i].end_pfn,
+                      extra_rmrr_units[j].base_pfn, 
extra_rmrr_units[j].end_pfn);
+                break;
+            }
+        }
+        /* Broke out of the overlap loop check, continue with next rmrr. */
+        if ( j < nr_rmrr )
+            continue;
+        list_for_each_entry(rmrru, &acpi_rmrr_units, list)
+        {
+            if ( pfn_to_paddr(extra_rmrr_units[i].base_pfn <= 
rmrru->end_address) &&
+                 rmrru->base_address <= 
pfn_to_paddr(extra_rmrr_units[i].end_pfn) )
+            {
+                printk(XENLOG_ERR VTDPREFIX
+                       "Overlapping extra RMRRs "PRI_RMRR(s,e)" and ACPI RMRRs 
"PRI_RMRR(s,e)"\n",
+                       extra_rmrr_units[i].base_pfn,
+                       extra_rmrr_units[i].end_pfn,
+                       paddr_to_pfn(rmrru->base_address),
+                       paddr_to_pfn(rmrru->end_address));
+                break;
+            }
+        }
+
+
+        pfn = extra_rmrr_units[i].base_pfn;
+        do
+        {
+            if ( !mfn_valid(pfn) || (pfn >> (paddr_bits - PAGE_SHIFT)) )
+            {
+                if ( iommu_verbose )
+                    printk(XENLOG_ERR VTDPREFIX
+                           "Invalid mfn in RMRR range "PRI_RMRR(s,e)"\n",
+                           extra_rmrr_units[i].base_pfn, 
extra_rmrr_units[i].end_pfn);
+                break;
+            }
+        } while ( pfn++ <= extra_rmrr_units[i].end_pfn );
+        /* The range had invalid mfn as the loop was broken out before 
reaching end_pfn. */
+        if ( pfn <= extra_rmrr_units[i].end_pfn )
+            continue;
+
+        acpi_rmrr = xzalloc(struct acpi_rmrr_unit);
+        if ( !acpi_rmrr )
+            return;
+
+        acpi_rmrr->scope.devices = xmalloc_array(u16,
+                                                 
extra_rmrr_units[i].dev_count);
+        if ( !acpi_rmrr->scope.devices )
+        {
+            xfree(acpi_rmrr);
+            return;
+        }
+
+        seg = 0;
+        for ( dev = 0; dev < extra_rmrr_units[i].dev_count; dev++ )
+        {
+            acpi_rmrr->scope.devices[dev] = extra_rmrr_units[i].sbdf[dev];
+            seg = seg | PCI_SEG(extra_rmrr_units[i].sbdf[dev]);
+        }
+        if ( seg != PCI_SEG(extra_rmrr_units[i].sbdf[0]) )
+        {
+            printk(XENLOG_ERR VTDPREFIX
+                   "Segments are not equal for RMRR range "PRI_RMRR(s,e)"\n",
+                   extra_rmrr_units[i].base_pfn, extra_rmrr_units[i].end_pfn);
+            scope_devices_free(&acpi_rmrr->scope);
+            xfree(acpi_rmrr);
+            continue;
+        }
+
+        acpi_rmrr->segment = seg;
+        acpi_rmrr->base_address = pfn_to_paddr(extra_rmrr_units[i].base_pfn);
+        acpi_rmrr->end_address = pfn_to_paddr(extra_rmrr_units[i].end_pfn + 1);
+        acpi_rmrr->scope.devices_cnt = extra_rmrr_units[i].dev_count;
+
+        if ( register_one_rmrr(acpi_rmrr) )
+        {
+            printk(XENLOG_ERR VTDPREFIX
+                   "Could not register RMMR range "PRI_RMRR(s,e)"\n",
+                   extra_rmrr_units[i].base_pfn, extra_rmrr_units[i].end_pfn);
+            scope_devices_free(&acpi_rmrr->scope);
+            xfree(acpi_rmrr);
+        }
+    }
+}
+
 #include <asm/tboot.h>
 /* ACPI tables may not be DMA protected by tboot, so use DMAR copy */
 /* SINIT saved in SinitMleData in TXT heap (which is DMA protected) */
@@ -878,6 +1010,7 @@ int __init acpi_dmar_init(void)
 {
     acpi_physical_address dmar_addr;
     acpi_native_uint dmar_len;
+    int ret;
 
     if ( ACPI_SUCCESS(acpi_get_table_phys(ACPI_SIG_DMAR, 0,
                                           &dmar_addr, &dmar_len)) )
@@ -888,7 +1021,10 @@ int __init acpi_dmar_init(void)
         dmar_table = __va(dmar_addr);
     }
 
-    return parse_dmar_table(acpi_parse_dmar);
+    ret = parse_dmar_table(acpi_parse_dmar);
+    add_extra_rmrr();
+
+    return ret;
 }
 
 void acpi_dmar_reinstate(void)
@@ -919,3 +1055,67 @@ int platform_supports_x2apic(void)
     unsigned int mask = ACPI_DMAR_INTR_REMAP | ACPI_DMAR_X2APIC_OPT_OUT;
     return cpu_has_x2apic && ((dmar_flags & mask) == ACPI_DMAR_INTR_REMAP);
 }
+
+/*
+ * Parse rmrr Xen command line options and add parsed device and region into
+ * acpi_rmrr_unit list to mapped as RMRRs parsed from ACPI.
+ * Format:
+ * 
rmrr=start<-end>=[s1]bdf1[,[s1]bdf2[,...]];start<-end>=[s2]bdf1[,[s2]bdf2[,...]]
+ * If the segment of the first device is not specified, segment zero will be 
used.
+ * If other segments are not specified, first device segment will be used.
+ * If a segment is specified for other than the first device and it does not 
match
+ * the one specified for the first one, an error will be reported.
+ */
+static void __init parse_rmrr_param(const char *str)
+{
+    const char *s = str, *cur, *stmp;
+    unsigned int seg, bus, dev, func;
+    unsigned long start, end;
+
+    do {
+        start = simple_strtoul(cur = s, &s, 0);
+        if ( cur == s )
+            break;
+
+        if ( *s == '-' )
+        {
+            end = simple_strtoul(cur = s + 1, &s, 0);
+            if ( cur == s )
+                break;
+        }
+        else
+            end = start;
+
+        extra_rmrr_units[nr_rmrr].base_pfn = start;
+        extra_rmrr_units[nr_rmrr].end_pfn = end;
+        extra_rmrr_units[nr_rmrr].dev_count = 0;
+
+        if ( *s != '=' )
+            continue;
+
+        do {
+            bool_t default_segment = 0;
+
+            if ( *s == ';' )
+                break;
+            stmp = __parse_pci(s + 1, &seg, &bus, &dev, &func, 
&default_segment);
+            if ( !stmp )
+                break;
+
+            /* Not specified segment will be replaced with one from first 
device. */
+            if ( extra_rmrr_units[nr_rmrr].dev_count && default_segment )
+                seg = PCI_SEG(extra_rmrr_units[nr_rmrr].sbdf[0]);
+
+            /* Keep sbdf's even if they differ and later report an error. */
+            
extra_rmrr_units[nr_rmrr].sbdf[extra_rmrr_units[nr_rmrr].dev_count] = 
PCI_SBDF(seg, bus, dev, func);
+            extra_rmrr_units[nr_rmrr].dev_count++;
+            s = stmp;
+        } while ( *s == ',' &&
+                  extra_rmrr_units[nr_rmrr].dev_count < MAX_EXTRA_RMRR_DEV );
+
+        if ( extra_rmrr_units[nr_rmrr].dev_count )
+            nr_rmrr++;
+
+    } while ( *s++ == ';' && nr_rmrr < MAX_EXTRA_RMRR );
+}
+custom_param("rmrr", parse_rmrr_param);
-- 
2.1.3


_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.