Re: [Xen-devel] [PATCH RFC 3/4] xen/pvhvm: Unmap all PIRQs on startup and shutdown

[David Vrabel <david.vrabel@xxxxxxxxxx>]

On 29/07/14 18:06, Vitaly Kuznetsov wrote:
> David Vrabel <david.vrabel@xxxxxxxxxx> writes:
> 
>> On 29/07/14 14:50, Vitaly Kuznetsov wrote:
>>> David Vrabel <david.vrabel@xxxxxxxxxx> writes:
>>>
>>>> On 15/07/14 14:40, Vitaly Kuznetsov wrote:
>>>>> When kexec is being run PIRQs from Qemu-emulated devices are still
>>>>> mapped to old event channels and new kernel has no information about
>>>>> that. Trying to map them twice results in the following in Xen's dmesg:
>>>>>
>>>>>  (XEN) irq.c:2278: dom7: pirq 24 or emuirq 8 already mapped
>>>>>  (XEN) irq.c:2278: dom7: pirq 24 or emuirq 12 already mapped
>>>>>  (XEN) irq.c:2278: dom7: pirq 24 or emuirq 1 already mapped
>>>>>  ...
>>>>>
>>>>>  and the following in new kernel's dmesg:
>>>>>
>>>>>  [   92.286796] xen:events: Failed to obtain physical IRQ 4
>>>>>
>>>>> The result is that the new kernel doesn't recieve IRQs for Qemu-emulated
>>>>> devices. Address the issue by unmapping all mapped PIRQs on kernel 
>>>>> shutdown
>>>>> when kexec was requested and on every kernel startup. We need to do this
>>>>> twice to deal with the following issues:
>>>>> - startup-time unmapping is required to make kdump work;
>>>>> - shutdown-time unmapping is required to support kexec-ing non-fixed 
>>>>> kernels;
>>>>> - shutdown-time unmapping is required to make Qemu-emulated NICs work 
>>>>> after
>>>>>   kexec (event channel is being closed on shutdown but no 
>>>>> PHYSDEVOP_unmap_pirq
>>>>>   is being performed).
>>>>
>>>> I think this should be done only in one place -- just prior to exec'ing
>>>> the new kernel (including kdump kernels).
>>>>
>>>
>>> Thank you for your comments!
>>>
>>> The problem I'm fighting wiht atm is: with FIFO-based event channels we
>>> need to call evtchn_fifo_destroy() so next EVTCHNOP_init_control won't
>>> fail. I was intended to put evtchn_fifo_destroy() in
>>> EVTCHNOP_reset. That introduces a problem: we need to deal with
>>> store/console channels. It is possible to remap those from guest with
>>> EVTCHNOP_bind_interdomain (if we remember where they were mapped before)
>>> but we can't do it after we did evtchn_fifo_destroy() and we can't
>>> rebind them after kexec and performing EVTCHNOP_init_control as
>>> we can't remember where these channels were mapped to after kexec/kdump.
>>>
>>> I see the following possible solutions:
>>> 1) We put evtchn_fifo_destroy() in EVTCHNOP_init_control so
>>> EVTCHNOP_init_control can be called twice. No EVTCHNOP_reset is required
>>> in that case.
>>
>> EVTCHNOP_init_control is called for each VCPU so I can't see how this
>> would work.
> 
> Right, forgot about that...
> 
>>
>>> 2) Introduce special (e.g. 'EVTCHNOP_fifo_destroy') hypercall to do
>>> evtchn_fifo_destroy() without closing all channels. Alternatively we can
>>> avoid closing all channels in EVTCHNOP_reset when called with DOMID_SELF
>>> (as this mode is not being used atm) -- but that would look unobvious.
>>
>> I would try this.  The guest prior to kexec would then:
>>
>> 1. Use EVTCHNOP_status to query remote end of console and xenstore event
>> channels.
>>
>> 2. Loop for all event channels:
>>
>> a. unmap pirq (if required)
>> b. EVTCHNOP_close
>>
>> 3. EVTCHNOP_fifo_destroy (the implementation of which must verify that
>> no channels are bound).
>>
>> 4. EVTCHNOP_bind_interdomain to rebind the console and xenstore channels.
>>
> 
> Yea, that's what I have now when I put evtchn_fifo_destroy() in
> EVTCHNOP_reset. The problem here is: we can't do
> EVTCHNOP_bind_interdomain after we did evtchn_fifo_destroy(), we need to
> call EVTCHNOP_init_control first. And we'll do that only after kexec so
> we won't remember what we need to remap.. The second issue is the fact
> that EVTCHNOP_bind_interdomain will remap store/storage channels to
> *some* local ports, not necessary matching hvm info
> (HVM_PARAM_CONSOLE_EVTCHN/HVM_PARAM_STORE_EVTCHN)..

You can set the HVM params to match.

> Would it be safe is instead of closing interdomain channels on
> EVTCHNOP_fifo_destroy we switch evtchn_port_ops to evtchn_port_ops_2l
> (so on EVTCHNOP_init_control after kexec we switch back)? I'll try
> prototyping this.

Switching the ops back to the 2l ones is an essential part of
fifo_destroy (the execed kernel might not have fifo support).  I assumed
you were already doing this.

David

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel