[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-devel] [PATCH] docs: improve documentation for the the dom0_mem command line option



On Wed, 2012-03-21 at 11:08 +0000, David Vrabel wrote:
> From: David Vrabel <david.vrabel@xxxxxxxxxx>
> 
> Signed-off-by: David Vrabel <david.vrabel@xxxxxxxxxx>
> ---
>  docs/misc/xen-command-line.markdown |   27 ++++++++++++++++++---------
>  1 files changed, 18 insertions(+), 9 deletions(-)
> 
> diff --git a/docs/misc/xen-command-line.markdown 
> b/docs/misc/xen-command-line.markdown
> index beb8462..c697d68 100644
> --- a/docs/misc/xen-command-line.markdown
> +++ b/docs/misc/xen-command-line.markdown
> @@ -8,7 +8,7 @@ This document coveres the command line options which the Xen 
> Hypervisor.
>  
>  Most parameters take the form `option=value`.  Different options on the 
> command line should be space delimited.
>  
> -### Boolean
> +### Boolean (`<boolean>`)
>  
>  All boolean option may be explicitly enabled using a `value` of
>  > `yes`, `on`, `true`, `enable` or `1`
> @@ -29,11 +29,11 @@ Disable x2apic support (if present)
>  Enable synchronous console mode
>  > `sync_console`
>  
> -### Integer
> +### Integer (`<integer>`)
>  
>  An integer parameter will default to decimal and may be prefixed with a `-` 
> for negative numbers.  Alternativly, a hexidecimal number may be used by 
> prefixing the number with `0x`, or an octal number may be used if a leading 
> `0` is present.
>  
> -### Size
> +### Size (`<size>`)
>  
>  A size parameter may be any integer, with a size suffix
>  
> @@ -96,7 +96,7 @@ Increase the verbosity of the APIC code from the default 
> value.
>  ### ats
>  ### availmem
>  ### badpage
> -> `= List of [ <integer> | <ingeter>-<integer> ]`
> +> `= List of [ <integer> | <integer>-<integer> ]`
>  
>  Specify that certain pages, or certain ranges of pages contain bad bytes and 
> should not be used.  For example, if your memory tester says that byte 
> `0x12345678` is bad, you would place `badpage=0x12345` on Xen's command line.
>  
> @@ -219,13 +219,22 @@ Specifiy the maximum number of vcpus to give to dom0.  
> This defaults to the numb
>  Specify the total size for dom0.
>  
>  ### dom0\_mem (x86)
> -> `= List of ( min:<value> | max: <value> | <value> )`
> +> `= List of ( min:<size> | max:<size> | <size> )`
>  
> -each `<value>` is a size parameter.  If the size is positive, it represents 
> an absolute value.  If the size is negative, the size specified is subtracted 
> from the total available memory.
> +Set the amount of memory for the initial domain (dom0). If a size is
> +positive, it represents an absolute value.  If a size is negative, the
> +size specified is subtracted from the total available memory.
>  
> -* `min:<value>` specifies the minimum amount of memory allocated to dom0.
> -* `max:<value>` specifies the maximum amount of memory allocated to dom0.
> -* `<value>` specified the exact amount of memory allocated to dom0.
> +* `min:<size>` specifies the minimum amount of memory allocated to dom0.
> +* `max:<size>` specifies the maximum amount of memory allocated to dom0.

This means "max:<size> => min(<size>,<actual-host-ram>)" and min vice
versa, right?

Or does min fail/panic if host-ram less than the given size?

> +* `<size>` specified the exact amount of memory allocated to dom0.

              specifies

If you give both min: and max: but not this which takes precedence?

> +`max:<size>` also sets the maximum reservation (the maximum amount of
> +memory dom0 can balloon up to).  If this is omitted then the maximum
> +reservation is unlimited.
> +
> +For example, to set dom0's memory to 512 MB but no more than 1 GB use
> +`dom0_mem=512M,max:1G`.

Perhaps:

For example, to set dom0's initial memory allocation to 512MB but allow
it to balloon up as far as 1GB use `dom0_mem=512M,max:1G`

Ian.

>  
>  ### dom0\_shadow
>  ### dom0\_vcpus\_pin



_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxx
http://lists.xen.org/xen-devel


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.