[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-devel] Re: [Xen-users] pvops dom0 kernel: Unable to locate IOAPIC for GSI 2 and 9



On Thu, Mar 18, 2010 at 01:23:41PM -0700, kishore kumar wrote:
>    pvdisplay does not work in my RHEL machine.
> 
>    I did  pvscan.
>    below is the output.
> 
>    PV /dev/sda2 VG VolGroup01 lvm2 [232.78 GB / 0 free]
> 
>    Total: 1 [232.78 GB] / in use: 1 [232.78 GB] / in no VG: 0 [0 ]
>

Ok so /dev/sda2 is the correct device holding the VolGroup01.

Looking at your latest capture.doc I see this: 

Command line: ro root=/dev/vg00/lv01  console=hvc0 earlyprintk=xen nomodeset 
initcall_debug debug swiotlb=force apic=debug loglevel=10

So your root= parameter is wrong! Edit grub.conf and replace it with the actual 
root device:
root=/dev/VolGroup01/LogVol00

-- Pasi
 
>    On Thu, Mar 18, 2010 at 12:31 PM, Pasi Kärkkäinen <[1]pasik@xxxxxx> wrote:
> 
>      On Thu, Mar 18, 2010 at 11:16:26AM -0700, kishore kumar wrote:
>      >    I did the below steps for pvops dom 0 kernel.
>      >
>      >    make menuconfig
>      >    make bzImage
>      >    make modules
>      >    make modules_install
>      >    cp -a .config /boot/config-2.6.32.10
>      >    cp -a System.map /boot/System.map-2.6.32.10
>      >    cp -a arch/x86/boot/bzImage /boot/vmlinuz-2.6.32.10
>      >    /sbin/mkinitrd -f --builtin=ahci /boot/initrd-2.6.32.10.img
>      2.6.32.10
>      >    I tried root=/dev/VolGroup01/LogVol00 .
>      >
> 
>      Ok.
> 
>      Please run "pvdisplay" to see which actual partition is the LVM PV for
>      your
>      volume group.
> 
>      Also if you're running Fedora 12 you could try generating an initrd
>      image
>      with dracut instead of mkinitrd.
> 
>      -- Pasi
> 
>      >
>      >    On Thu, Mar 18, 2010 at 9:15 AM, Pasi Kärkkäinen
>      <[1][2]pasik@xxxxxx> wrote:
>      >
>      >      On Wed, Mar 17, 2010 at 03:20:13PM -0700, kishore kumar wrote:
>      >      >    Here is the output of df -h and cat /etc/fstab of my
>      machine.
>      >      >
>      >
>      >      Did you try both root=/dev/mapper/VolGroup01-LogVol00 and
>      >      root=/dev/VolGroup01/LogVol00 arguments for the dom0 kernel?
>      >
>      >      How did you generate the initrd image for the dom0 kernel?
>      >
>      >      Anyway this sounds like a grub.conf or initrd problem, not Xen or
>      pvops
>      >      dom0 kernel kernel problem.
>      >
>      >      -- Pasi
>      >
>      >      >    Please let me know your thoughts.
>      >      >
>      >      >    [root@localhost kishore]# df -h
>      >      >
>      >      >    Filesystem Size Used Avail Use% Mounted on
>      >      >
>      >      >    /dev/mapper/VolGroup01-LogVol00
>      >      >
>      >      >                                        223G 29G 182G 14% /
>      >      >
>      >      >    /dev/sda1 99M 81M 13M 87% /boot
>      >      >
>      >      >    tmpfs 757M 0 757M 0% /dev/shm
>      >      >
>      >      >    [root@localhost kishore]# cat /etc/fstab
>      >      >
>      >      >    /dev/VolGroup01/LogVol00 / ext3 defaults 1 1
>      >      >
>      >      >    LABEL=/boot /boot ext3 defaults 1 2
>      >      >
>      >      >    tmpfs /dev/shm tmpfs defaults 0 0
>      >      >
>      >      >    devpts /dev/pts devpts gid=5,mode=620 0 0
>      >      >
>      >      >    sysfs /sys sysfs defaults 0 0
>      >      >
>      >      >    proc /proc proc defaults 0 0
>      >      >
>      >      >    /dev/VolGroup01/LogVol01 swap swap defaults 0 0
>      >      >
>      >      >    [root@localhost kishore]#
>      >      >
>      >      >    On Tue, Mar 16, 2010 at 4:18 PM, Pasi Kärkkäinen
>      >      <[1][2][3]pasik@xxxxxx> wrote:
>      >      >
>      >      >      On Tue, Mar 16, 2010 at 03:40:46PM -0700, kishore kumar
>      wrote:
>      >      >      >    I am not sure.  Can you please let me know how to
>      check
>      >      this? any
>      >      >      command
>      >      >      >    ??
>      >      >
>      >      >      well simple "df -h" will show it. and also "cat
>      /etc/fstab".
>      >      >      You can also check it from your grub configuration.. from
>      the
>      >      working
>      >      >      baremetal (non-Xen) entry.
>      >      >
>      >      >      -- Pasi
>      >      >      >
>      >      >      >    On Tue, Mar 16, 2010 at 3:29 PM, Pasi Kärkkäinen
>      >      >      <[1][2][3][4]pasik@xxxxxx> wrote:
>      >      >      >
>      >      >      >      On Tue, Mar 16, 2010 at 03:22:50PM -0700, kishore
>      kumar
>      >      wrote:
>      >      >      >      >    attached  is the log captured in with the word
>      >      document .
>      >      >      >      >
>      >      >      >
>      >      >      >      Scanning logical volumes
>      >      >      >       Reading all physical volumes.  This may take a
>      while...
>      >      >      >      Activating logical volumes
>      >      >      >       Volume group "VolGroup01" not found
>      >      >      >      Trying to resume from /dev/VolGroup01/LogVol01
>      >      >      >      Unable to access resume device
>      (/dev/VolGroup01/LogVol01)
>      >      >      >      Creating root device.
>      >      >      >      Mounting root filesystem.
>      >      >      >      mount: could not find filesystem '/dev/root'
>      >      >      >      Setting up other filesystems.
>      >      >      >      Setting up new root fs
>      >      >      >      setuproot: moving /dev failed: No such file or
>      directory
>      >      >      >      no fstab.sys, mounting internal defaults
>      >      >      >      setuproot: error mounting /proc: No such file or
>      directory
>      >      >      >      setuproot: error mounting /sys: No such file or
>      directory
>      >      >      >      Switching to new root and running init.
>      >      >      >      unmounting old /dev
>      >      >      >      unmounting old /proc
>      >      >      >      unmounting old /sys
>      >      >      >      switchroot: mount failed: No such file or directory
>      >      >      >      init used greatest stack depth: 4088 bytes left
>      >      >      >      Kernel panic - not syncing: Attempted to kill init!
>      >      >      >
>      >      >      >      So it seems it gets all the way to executing the
>      initrd
>      >      image,
>      >      >      >      which then fails to mount the root fs.
>      >      >      >
>      >      >      >      Earlier in the log:
>      >      >      >      ata1: SATA link up 3.0 Gbps (SStatus 123 SControl
>      300)
>      >      >      >      ata1.00: ATA-8: Hitachi HDT721025SLA380, STBOA3AA,
>      max
>      >      UDMA/133
>      >      >      >      ata1.00: 488397168 sectors, multi 0: LBA48 NCQ
>      (depth
>      >      31/32), AA
>      >      >      >      ata1.00: configured for UDMA/133
>      >      >      >      scsi 0:0:0:0: Direct-Access     ATA      Hitachi
>      HDT72102
>      >      STBO
>      >      >      PQ: 0
>      >      >      >      ANSI: 5
>      >      >      >      sd 0:0:0:0: Attached scsi generic sg0 type 0
>      >      >      >      sd 0:0:0:0: [sda] 488397168 512-byte logical
>      blocks: (250
>      >      GB/232
>      >      >      GiB)
>      >      >      >      sd 0:0:0:0: [sda] Write Protect is off
>      >      >      >      sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
>      >      >      >      sd 0:0:0:0: [sda] Write cache: enabled, read cache:
>      >      enabled,
>      >      >      doesn't
>      >      >      >      support DPO or FUA
>      >      >      >       sda: sda1 sda2
>      >      >      >      sd 0:0:0:0: [sda] Attached SCSI disk
>      >      >      >
>      >      >      >      so /dev/sda was detected. Is your root lvm volume
>      on
>      >      /dev/sda ?
>      >      >      >      Is /dev/VolGroup01/LogVol01 really your root fs?
>      >      >      >
>      >      >      >      -- Pasi
>      >      >      >
>      >      >      >      >
>      >      >      >      >
>      >      >      >      >    On Tue, Mar 16, 2010 at 3:03 PM, Pasi
>      Kärkkäinen
>      >      >      >      <[1][2][3][4][5]pasik@xxxxxx> wrote:
>      >      >      >      >
>      >      >      >      >      On Tue, Mar 16, 2010 at 02:56:06PM -0700,
>      kishore
>      >      kumar
>      >      >      wrote:
>      >      >      >      >      >    Please find the attached log file after
>      fixing
>      >      the
>      >      >      dom 0
>      >      >      >      kernel cmd
>      >      >      >      >      line
>      >      >      >      >      >    as below
>      >      >      >      >      >
>      >      >      >      >      >    ro root=/dev/VolGroup01/LogVol00
>      console=hvc0
>      >      >      >      earlyprintk=xen
>      >      >      >      >      nomodeset
>      >      >      >      >      >
>      >      >      >      >
>      >      >      >      >      There's something wrong with the log, the
>      dom0
>      >      kernel
>      >      >      parts are
>      >      >      >      all on
>      >      >      >      >      one line..
>      >      >      >      >      It's really difficult to read it.
>      >      >      >      >
>      >      >      >      >      -- Pasi
>      >      >      >      >
>      >      >      >      >      >    Thanks
>      >      >      >      >      >
>      >      >      >      >      >
>      >      >      >      >      >    On Tue, Mar 16, 2010 at 2:29 PM, Pasi
>      >      Kärkkäinen
>      >      >      >      >      <[1][2][3][4][5][6]pasik@xxxxxx> wrote:
>      >      >      >      >      >
>      >      >      >      >      >      On Tue, Mar 16, 2010 at 02:16:22PM
>      -0700,
>      >      kishore
>      >      >      kumar
>      >      >      >      wrote:
>      >      >      >      >      >      >    I did below steps.
>      >      >      >      >      >      >
>      >      >      >      >      >      >
>      >      >      >      >      >      >     I pulled DOM 0 kernel from
>      >      >      >      >      >      >    git clone
>      >      >      >      >      >
>      >      >      >      >
>      >      >      >
>      >      >
>      >
>       
> git://[1][2][3][4][5][6][7]git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>      >      >      >      >      >      >    linux-2.6-xen
>      >      >      >      >      >      >
>      >      >      >      >      >      >    cd linux-2.6-xen
>      >      >      >      >      >      >
>      >      >      >      >      >      >    make clean
>      >      >      >      >      >      >
>      >      >      >      >      >      >    cp -a .config .config-old
>      >      >      >      >      >      >
>      >      >      >      >      >      >    wget -O .config
>      >      >      >      >      >      >
>      >      >      >      >      >
>      >      >      >      >
>      >      >      >
>      >      >
>      >
>      
> [2][3][4][5][6][7][8]http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>      >      >      >      >      >      >
>      >      >      >      >      >      >    make oldconfig
>      >      >      >      >      >      >
>      >      >      >      >      >      >    make bzImage
>      >      >      >      >      >      >
>      >      >      >      >      >      >    make modules
>      >      >      >      >      >      >
>      >      >      >      >      >      >    make modules_install
>      >      >      >      >      >      >
>      >      >      >      >      >      >    cp -a .config
>      /boot/config-2.6.32.9
>      >      >      >      >      >      >
>      >      >      >      >      >      >    cp -a System.map
>      >      /boot/System.map-2.6.32.9
>      >      >      >      >      >      >
>      >      >      >      >      >      >    cp -a arch/x86/boot/bzImage
>      >      >      /boot/vmlinuz-2.6.32.9
>      >      >      >      >      >      >
>      >      >      >      >      >      >    and modified the grub.conf as
>      below
>      >      >      >      >      >      >
>      >      >      >      >      >      >
>      >      >      >      >      >      >    Root(hd0,0)
>      >      >      >      >      >      >
>      >      >      >      >      >      >     kernel /xen.gz console=vga,com1
>      >      >      com1=115200,8n1
>      >      >      >      msi=1
>      >      >      >      >      iommu=1
>      >      >      >      >      >      >
>      >      >      >      >      >      >     module /vmlinuz-2.6.32.9 ro
>      >      >      >      root=/dev/VolGroup01/LogVo100
>      >      >      >      >       rhgb
>      >      >      >      >      >      quiet
>      >      >      >      >      >      >
>      >      >      >      >      >      >     module /initrd-2.6.32.9.img
>      >      >      >      >      >      >
>      >      >      >      >      >      >
>      >      >      >      >      >      >    and rebooted the machine.  Then
>      It
>      >      booted with
>      >      >      some
>      >      >      >      xen
>      >      >      >      >      messages
>      >      >      >      >      >      and
>      >      >      >      >      >      >    stopped.  Those were the
>      messages
>      >      captured
>      >      >      from
>      >      >      >      serial
>      >      >      >      >      console.
>      >      >      >      >      >      >
>      >      >      >      >      >      >    Please let me know if I did
>      something
>      >      wrong
>      >      >      here.
>      >      >      >      >      >      >
>      >      >      >      >      >
>      >      >      >      >      >      Please fix the kernel cmdline based
>      on my
>      >      earlier
>      >      >      email,
>      >      >      >      and
>      >      >      >      >      capture and
>      >      >      >      >      >      post the
>      >      >      >      >      >      serial console log again!
>      >      >      >      >      >
>      >      >      >      >      >      -- Pasi
>      >      >      >      >      >      >
>      >      >      >      >      >      >
>      >      >      >      >      >      >    On Tue, Mar 16, 2010 at 1:20 PM,
>      Pasi
>      >      >      Kärkkäinen
>      >      >      >      >      >      <[3][4][5][6][7][8][9]pasik@xxxxxx>
>      wrote:
>      >      >      >      >      >      >
>      >      >      >      >      >      >      On Tue, Mar 16, 2010 at
>      01:16:28PM
>      >      -0700,
>      >      >      Jeremy
>      >      >      >      >      Fitzhardinge
>      >      >      >      >      >      wrote:
>      >      >      >      >      >      >      > On 03/16/2010 12:48 PM, Pasi
>      >      Kärkkäinen
>      >      >      wrote:
>      >      >      >      >      >      >      >> On Tue, Mar 16, 2010 at
>      09:43:44PM
>      >      +0200,
>      >      >      Pasi
>      >      >      >      >      Kärkkäinen
>      >      >      >      >      >      wrote:
>      >      >      >      >      >      >      >>
>      >      >      >      >      >      >      >>> On Tue, Mar 16, 2010 at
>      >      10:32:17AM
>      >      >      -0700,
>      >      >      >      kishore
>      >      >      >      >      kumar
>      >      >      >      >      >      wrote:
>      >      >      >      >      >      >      >>>
>      >      >      >      >      >      >      >>>>     Attached is the
>      output
>      >      captured
>      >      >      from
>      >      >      >      serial
>      >      >      >      >      console.
>      >      >      >      >      >      >      >>>>
>      >      >      >      >      >      >      >>>>     Machine does not boot
>      after
>      >      >      compiling xen
>      >      >      >      3.4.3
>      >      >      >      >      with
>      >      >      >      >      >      pv_ops dom
>      >      >      >      >      >      >      0 kernel.
>      >      >      >      >      >      >      >>>>
>      >      >      >      >      >      >      >>>>     Please let me know
>      what is
>      >      going
>      >      >      wrong
>      >      >      >      here.
>      >      >      >      >      >      >      >>>>
>      >      >      >      >      >      >      >>>>
>      >      >      >      >      >      >      >>> Ok this looks like a bug
>      that is
>      >      already
>      >      >      being
>      >      >      >      sorted
>      >      >      >      >      out on
>      >      >      >      >      >      >      xen-devel mailinglist.
>      >      >      >      >      >      >      >>> I added CC to xen-devel.
>      >      >      >      >      >      >      >>>
>      >      >      >      >      >      >      >>>
>      >      >      >      >      >      >      >>
>      >      >      >      >      >      >      >
>      >      >      >      >      >      >      > Those messages are not a
>      problem in
>      >      >      themselves,
>      >      >      >      but the
>      >      >      >      >      related
>      >      >      >      >      >      >      problem
>      >      >      >      >      >      >      > is believed to be fixed in
>      current
>      >      >      >      xen/stable-2.6.32.x.
>      >      >      >      >       It
>      >      >      >      >      >      looks like
>      >      >      >      >      >      >      > the output stops there
>      because the
>      >      Xen
>      >      >      console
>      >      >      >      isn't set
>      >      >      >      >      up
>      >      >      >      >      >      properly
>      >      >      >      >      >      >      for
>      >      >      >      >      >      >      > some reason.
>      >      >      >      >      >      >      >
>      >      >      >      >      >      >
>      >      >      >      >      >      >      Yeah, remove "rhgb quiet" from
>      the
>      >      options..
>      >      >      the
>      >      >      >      dom0
>      >      >      >      >      kernel
>      >      >      >      >      >      cmdline
>      >      >      >      >      >      >      should be like this:
>      >      >      >      >      >      >      ro
>      root=/dev/VolGroup01/LogVol00
>      >      >      console=hvc0
>      >      >      >      >      earlyprintk=xen
>      >      >      >      >      >      nomodeset
>      >      >      >      >      >      >      -- Pasi
>      >      >      >      >      >      >
>      >      >      >      >      >      > References
>      >      >      >      >      >      >
>      >      >      >      >      >      >    Visible links
>      >      >      >      >      >      >    1.
>      >      >      >      >
>      >      >      >
>      >      >
>      >
>      
> [5][6][7][8][9][10]http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>      >      >      >      >      >      >    2.
>      >      >      >      >      >
>      >      >      >      >
>      >      >      >
>      >      >
>      >
>       
> [6][7][8][9][10][11]http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>      >      >      >      >      >      >    3.
>      mailto:[7][8][9][10][11][12]pasik@xxxxxx
>      >      >      >      >      >
>      >      >      >      >      > References
>      >      >      >      >      >
>      >      >      >      >      >    Visible links
>      >      >      >      >      >    1.
>      mailto:[9][10][11][12][13]pasik@xxxxxx
>      >      >      >      >      >    2.
>      >      >      >      >
>      >      >      >
>      >      >
>      >
>      
> [10][11][12][13][14]http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>      >      >      >      >      >    3.
>      >      >      >      >
>      >      >      >
>      >      >
>      >
>      
> [11][12][13][14][15]http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>      >      >      >      >      >    4.
>      mailto:[12][13][14][15][16]pasik@xxxxxx
>      >      >      >      >      >    5.
>      >      >      >      >
>      >      >      >
>      >      >
>      >
>      
> [13][14][15][16][17]http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>      >      >      >      >      >    6.
>      >      >      >      >
>      >      >      >
>      >      >
>      >
>      
> [14][15][16][17][18]http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>      >      >      >      >      >    7.
>      mailto:[15][16][17][18][19]pasik@xxxxxx
>      >      >      >      >      > Asserting Post complete GPIO!!!
>      >      >      >      >      > Transfer control to CSM 16-bit binary for
>      legacy
>      >      boot
>      >      >      >      >      >  __  __            _____ _  _    _____
>      >        _  _
>      >      >      >      >      >  \ \/ /___ _ __   |___ /| || |  |___ /
>       _ __
>      >      ___| || |
>      >      >          _
>      >      >      >      __  _
>      >      >      >      >      __ ___
>      >      >      >      >      >   \  // _ \ '_ \    |_ \| || |_   |_ \ __|
>      '__/
>      >      __| ||
>      >      >      |_ __|
>      >      >      >      '_ \|
>      >      >      >      >      '__/ _ \
>      >      >      >      >      >   /  \  __/ | | |  ___) |__   _| ___) |__|
>      | |
>      >      (__|__
>      >      >      _|__|
>      >      >      >      |_) | |
>      >      >      >      >      |  __/
>      >      >      >      >      >  /_/\_\___|_| |_| |____(_) |_|(_)____/
>      |_|
>      >       \___|  |_|
>      >      >         |
>      >      >      >      .__/|_|
>      >      >      >      >       \___|
>      >      >      >      >      >
>      >      >          |_|
>      >      >      >      >      > (XEN) Xen version 3.4.3-rc4-pre
>      >      (kishore@localdomain)
>      >      >      (gcc
>      >      >      >      version
>      >      >      >      >      4.1.2 20080704 (Red Hat 4.1.2-46)) Mon Mar
>      15
>      >      13:44:31 PDT
>      >      >      2010
>      >      >      >      >      > (XEN) Latest ChangeSet: Tue Mar 09
>      18:15:52 2010
>      >      +0000
>      >      >      >      >      19924:6e72f8c3c017
>      >      >      >      >      > (XEN) Command line: console=vga,com1
>      >      com1=115200,8n1
>      >      >      msi=1
>      >      >      >      iommu=1
>      >      >      >      >      > (XEN) Video information:
>      >      >      >      >      > (XEN)  VGA is text mode 80x25, font 8x16
>      >      >      >      >      > (XEN)  VBE/DDC methods: none; EDID
>      transfer time:
>      >      0
>      >      >      seconds
>      >      >      >      >      > (XEN)  EDID info not retrieved because no
>      DDC
>      >      retrieval
>      >      >      method
>      >      >      >      >      detected
>      >      >      >      >      > (XEN) Disc information:
>      >      >      >      >      > (XEN)  Found 1 MBR signatures
>      >      >      >      >      > (XEN)  Found 1 EDD information structures
>      >      >      >      >      > (XEN) Xen-e820 RAM map:
>      >      >      >      >      > (XEN)  0000000000000000 - 000000000009d000
>      >      (usable)
>      >      >      >      >      > (XEN)  000000000009d000 - 00000000000a0000
>      >      (reserved)
>      >      >      >      >      > (XEN)  00000000000e0000 - 0000000000100000
>      >      (reserved)
>      >      >      >      >      > (XEN)  0000000000100000 - 000000006d597000
>      >      (usable)
>      >      >      >      >      > (XEN)  000000006d597000 - 000000006d686000
>      >      (reserved)
>      >      >      >      >      > (XEN)  000000006d686000 - 000000006f598000
>      >      (usable)
>      >      >      >      >      > (XEN)  000000006f598000 - 000000006f59a000
>      >      (reserved)
>      >      >      >      >      > (XEN)  000000006f59a000 - 000000006f5af000
>      (ACPI
>      >      NVS)
>      >      >      >      >      > (XEN)  000000006f5af000 - 000000006f5d9000
>      >      (reserved)
>      >      >      >      >      > (XEN)  000000006f5d9000 - 000000006f5f9000
>      (ACPI
>      >      data)
>      >      >      >      >      > (XEN)  000000006f5f9000 - 000000006f6df000
>      (ACPI
>      >      NVS)
>      >      >      >      >      > (XEN)  000000006f6df000 - 000000006f700000
>      (ACPI
>      >      data)
>      >      >      >      >      > (XEN)  000000006f700000 - 0000000080000000
>      >      (reserved)
>      >      >      >      >      > (XEN)  00000000a0000000 - 00000000b0000000
>      >      (reserved)
>      >      >      >      >      > (XEN)  00000000fc000000 - 00000000fd000000
>      >      (reserved)
>      >      >      >      >      > (XEN)  00000000fed1c000 - 00000000fed20000
>      >      (reserved)
>      >      >      >      >      > (XEN)  00000000ffc00000 - 0000000100000000
>      >      (reserved)
>      >      >      >      >      > (XEN) System RAM: 1780MB (1823000kB)
>      >      >      >      >      > (XEN) ACPI: RSDP 000F03F0, 0024 (r2 INTEL
>      )
>      >      >      >      >      > (XEN) ACPI: XSDT 6F6FE120, 0064 (r1 INTEL
>       THRLY
>      >      >        0
>      >      >      >      >      1000013)
>      >      >      >      >      > (XEN) ACPI: FACP 6F6FD000, 00F4 (r4 INTEL
>       THRLY
>      >      >        0
>      >      >      >      MSFT
>      >      >      >      >       100000D)
>      >      >      >      >      > (XEN) ACPI: DSDT 6F6F5000, 74F1 (r2 INTEL
>       THRLY
>      >      >        3
>      >      >      >      MSFT
>      >      >      >      >       100000D)
>      >      >      >      >      > (XEN) ACPI: FACS 6F5F9000, 0040
>      >      >      >      >      > (XEN) ACPI: APIC 6F6F4000, 01CC (r2 INTEL
>       THRLY
>      >      >        0
>      >      >      >      MSFT
>      >      >      >      >       100000D)
>      >      >      >      >      > (XEN) ACPI: MCFG 6F6F3000, 003C (r1 INTEL
>       THRLY
>      >      >        1
>      >      >      >      MSFT
>      >      >      >      >       100000D)
>      >      >      >      >      > (XEN) ACPI: HPET 6F6F2000, 0038 (r1 INTEL
>       THRLY
>      >      >        1
>      >      >      >      MSFT
>      >      >      >      >       100000D)
>      >      >      >      >      > (XEN) ACPI: SLIT 6F6F1000, 0030 (r1 INTEL
>       THRLY
>      >      >        1
>      >      >      >      MSFT
>      >      >      >      >       100000D)
>      >      >      >      >      > (XEN) ACPI: WDDT 6F6F0000, 0040 (r1 INTEL
>       THRLY
>      >      >        0
>      >      >      >      MSFT
>      >      >      >      >       100000D)
>      >      >      >      >      > (XEN) ACPI: SSDT 6F5D9000, 1FDDC (r1
>       INTEL SSDT
>      >       PM
>      >      >      4000
>      >      >      >      INTL
>      >      >      >      >      20061109)
>      >      >      >      >      > (XEN) ACPI: DMAR 6F6EE000, 01D0 (r1 INTEL
>       THRLY
>      >      >        1
>      >      >      >      MSFT
>      >      >      >      >       100000D)
>      >      >      >      >      > (XEN) Domain heap initialised
>      >      >      >      >      > (XEN) Processor #0 6:12 APIC version 21
>      >      >      >      >      > (XEN) Processor #2 6:12 APIC version 21
>      >      >      >      >      > (XEN) Processor #4 6:12 APIC version 21
>      >      >      >      >      > (XEN) Processor #16 6:12 APIC version 21
>      >      >      >      >      > (XEN) Processor #18 6:12 APIC version 21
>      >      >      >      >      > (XEN) Processor #20 6:12 APIC version 21
>      >      >      >      >      > (XEN) Processor #1 6:12 APIC version 21
>      >      >      >      >      > (XEN) Processor #3 6:12 APIC version 21
>      >      >      >      >      > (XEN) Processor #5 6:12 APIC version 21
>      >      >      >      >      > (XEN) Processor #17 6:12 APIC version 21
>      >      >      >      >      > (XEN) Processor #19 6:12 APIC version 21
>      >      >      >      >      > (XEN) Processor #21 6:12 APIC version 21
>      >      >      >      >      > (XEN) IOAPIC[0]: apic_id 8, version 32,
>      address
>      >      >      0xfec00000, GSI
>      >      >      >      0-23
>      >      >      >      >      > (XEN) IOAPIC[1]: apic_id 9, version 32,
>      address
>      >      >      0xfec90000, GSI
>      >      >      >      24-47
>      >      >      >      >      > (XEN) Enabling APIC mode:  Phys.  Using 2
>      I/O
>      >      APICs
>      >      >      >      >      > (XEN) Intel VT-d DMAR tables have been
>      parsed.
>      >      >      >      >      > (XEN) Using scheduler: SMP Credit
>      Scheduler
>      >      (credit)
>      >      >      >      >      > (XEN) Detected 3200.207 MHz processor.
>      >      >      >      >      > (XEN) VMX: Supported advanced features:
>      >      >      >      >      > (XEN)  - APIC MMIO access virtualisation
>      >      >      >      >      > (XEN)  - APIC TPR shadow
>      >      >      >      >      > (XEN)  - Extended Page Tables (EPT)
>      >      >      >      >      > (XEN)  - Virtual-Processor Identifiers
>      (VPID)
>      >      >      >      >      > (XEN)  - Virtual NMI
>      >      >      >      >      > (XEN)  - MSR direct-access bitmap
>      >      >      >      >      > (XEN) VMX: EPT is available.
>      >      >      >      >      > (XEN) VMX: VPID is available.
>      >      >      >      >      > (XEN) HVM: VMX enabled
>      >      >      >      >      > (XEN) HVM: Hardware Assisted Paging
>      detected.
>      >      >      >      >      > (XEN) CPU0: Intel Genuine Intel(R) CPU
>      >        000
>      >      >       @
>      >      >      >      3.20GHz
>      >      >      >      >      stepping 00
>      >      >      >      >      > (XEN) Booting processor 1/2 eip 88000
>      >      >      >      >      > (XEN) CPU1: Intel Genuine Intel(R) CPU
>      >        000
>      >      >       @
>      >      >      >      3.20GHz
>      >      >      >      >      stepping 00
>      >      >      >      >      > (XEN) Booting processor 2/4 eip 88000
>      >      >      >      >      > (XEN) CPU2: Intel Genuine Intel(R) CPU
>      >        000
>      >      >       @
>      >      >      >      3.20GHz
>      >      >      >      >      stepping 00
>      >      >      >      >      > (XEN) Booting processor 3/16 eip 88000
>      >      >      >      >      > (XEN) CPU3: Intel Genuine Intel(R) CPU
>      >        000
>      >      >       @
>      >      >      >      3.20GHz
>      >      >      >      >      stepping 00
>      >      >      >      >      > (XEN) Booting processor 4/18 eip 88000
>      >      >      >      >      > (XEN) CPU4: Intel Genuine Intel(R) CPU
>      >        000
>      >      >       @
>      >      >      >      3.20GHz
>      >      >      >      >      stepping 00
>      >      >      >      >      > (XEN) Booting processor 5/20 eip 88000
>      >      >      >      >      > (XEN) CPU5: Intel Genuine Intel(R) CPU
>      >        000
>      >      >       @
>      >      >      >      3.20GHz
>      >      >      >      >      stepping 00
>      >      >      >      >      > (XEN) Booting processor 6/1 eip 88000
>      >      >      >      >      > (XEN) CPU6: Intel Genuine Intel(R) CPU
>      >        000
>      >      >       @
>      >      >      >      3.20GHz
>      >      >      >      >      stepping 00
>      >      >      >      >      > (XEN) Booting processor 7/3 eip 88000
>      >      >      >      >      > (XEN) CPU7: Intel Genuine Intel(R) CPU
>      >        000
>      >      >       @
>      >      >      >      3.20GHz
>      >      >      >      >      stepping 00
>      >      >      >      >      > (XEN) Booting processor 8/5 eip 88000
>      >      >      >      >      > (XEN) CPU8: Intel Genuine Intel(R) CPU
>      >        000
>      >      >       @
>      >      >      >      3.20GHz
>      >      >      >      >      stepping 00
>      >      >      >      >      > (XEN) Booting processor 9/17 eip 88000
>      >      >      >      >      > (XEN) CPU9: Intel Genuine Intel(R) CPU
>      >        000
>      >      >       @
>      >      >      >      3.20GHz
>      >      >      >      >      stepping 00
>      >      >      >      >      > (XEN) Booting processor 10/19 eip 88000
>      >      >      >      >      > (XEN) CPU10: Intel Genuine Intel(R) CPU
>      >        000
>      >      >       @
>      >      >      >      3.20GHz
>      >      >      >      >      stepping 00
>      >      >      >      >      > (XEN) Booting processor 11/21 eip 88000
>      >      >      >      >      > (XEN) CPU11: Intel Genuine Intel(R) CPU
>      >        000
>      >      >       @
>      >      >      >      3.20GHz
>      >      >      >      >      stepping 00
>      >      >      >      >      > (XEN) Total of 12 processors activated.
>      >      >      >      >      > (XEN) ENABLING IO-APIC IRQs
>      >      >      >      >      > (XEN)  -> Using new ACK method
>      >      >      >      >      > (XEN) checking TSC synchronization across
>      12
>      >      CPUs:
>      >      >      passed.
>      >      >      >      >      > (XEN) Platform timer is 14.318MHz HPET
>      >      >      >      >      > ?(XEN) Brought up 12 CPUs
>      >      >      >      >      > (XEN) Intel VT-d Snoop Control supported.
>      >      >      >      >      > (XEN) Intel VT-d DMA Passthrough not
>      supported.
>      >      >      >      >      > (XEN) Intel VT-d Queued Invalidation
>      supported.
>      >      >      >      >      > (XEN) Intel VT-d Interrupt Remapping
>      supported.
>      >      >      >      >      > (XEN) I/O virtualisation enabled
>      >      >      >      >      > (XEN) I/O virtualisation for PV guests
>      disabled
>      >      >      >      >      > (XEN) xenoprof: Initialization failed.
>      Intel
>      >      processor
>      >      >      model 44
>      >      >      >      for P6
>      >      >      >      >      class family is not supported
>      >      >      >      >      > (XEN) *** LOADING DOMAIN 0 ***
>      >      >      >      >      > (XEN)  Xen  kernel: 64-bit, lsb, compat32
>      >      >      >      >      > (XEN)  Dom0 kernel: 64-bit, PAE, lsb,
>      paddr
>      >      0x1000000 ->
>      >      >      >      0x26bb000
>      >      >      >      >      > (XEN) PHYSICAL MEMORY ARRANGEMENT:
>      >      >      >      >      > (XEN)  Dom0 alloc.:
>      >      0000000064000000->0000000068000000
>      >      >      >      (404490 pages
>      >      >      >      >      to be allocated)
>      >      >      >      >      > (XEN) VIRTUAL MEMORY ARRANGEMENT:
>      >      >      >      >      > (XEN)  Loaded kernel:
>      >      ffffffff81000000->ffffffff826bb000
>      >      >      >      >      > (XEN)  Init. ramdisk:
>      >      ffffffff826bb000->ffffffff82d0d800
>      >      >      >      >      > (XEN)  Phys-Mach map:
>      >      ffffffff82d0e000->ffffffff83044050
>      >      >      >      >      > (XEN)  Start info:
>      >       ffffffff83045000->ffffffff830454b4
>      >      >      >      >      > (XEN)  Page tables:
>      >      ffffffff83046000->ffffffff83063000
>      >      >      >      >      > (XEN)  Boot stack:
>      >       ffffffff83063000->ffffffff83064000
>      >      >      >      >      > (XEN)  TOTAL:
>      >      ffffffff80000000->ffffffff83400000
>      >      >      >      >      > (XEN)  ENTRY ADDRESS: ffffffff819c1200
>      >      >      >      >      > (XEN) Dom0 has maximum 12 VCPUs
>      >      >      >      >      > (XEN) Scrubbing Free RAM: .done.
>      >      >      >      >      > (XEN) Xen trace buffers: disabled
>      >      >      >      >      > (XEN) Std. Loglevel: Errors and warnings
>      >      >      >      >      > (XEN) Guest Loglevel: Nothing
>      (Rate-limited:
>      >      Errors and
>      >      >      >      warnings)
>      >      >      >      >      > (XEN) Xen is relinquishing VGA console.
>      >      >      >      >      > (XEN) *** Serial input -> DOM0 (type
>      'CTRL-a'
>      >      three
>      >      >      times to
>      >      >      >      switch
>      >      >      >      >      input to Xen)
>      >      >      >      >      > (XEN) Freed 128kB init memory.
>      >      >      >      >      > mapping kernel into physical memory
>      >      >      >      >      > Xen: setup ISA identity maps
>      >      >      >      >      > about to get started...
>      >      >      >      >      > Initializing cgroup subsys cpuset
>      >      >      >      >      > Initializing cgroup subsys cpu
>      >      >      >      >      > Linux version 2.6.32.9
>      >      (kishore@xxxxxxxxxxxxxxxxxxxxx)
>      >      >      (gcc
>      >      >      >      version
>      >      >      >      >      4.1.2 20080704 (Red Hat 4.1.2-46)) #1 SMP
>      Mon Mar
>      >      15
>      >      >      15:16:28 PDT
>      >      >      >      2010
>      >      >      >      >      > Command line: ro
>      root=/dev/VolGroup01/LogVol00
>      >      >      console=hvc0
>      >      >      >      >      earlyprintk=xen nomodeset
>      >      >      >      >      > KERNEL supported cpus:
>      >      >      >      >      >   Intel GenuineIntel
>      >      >      >      >      >   AMD AuthenticAMD
>      >      >      >      >      >   Centaur CentaurHauls
>      >      >      >      >      > BIOS-provided physical RAM map:
>      >      >      >      >      >  Xen: 0000000000000000 - 000000000009d000
>      >      (usable)
>      >      >      >      >      >  Xen: 000000000009d000 - 0000000000100000
>      >      (reserved)
>      >      >      >      >      >  Xen: 0000000000100000 - 0000000066c0a000
>      >      (usable)
>      >      >      >      >      >  Xen: 000000006d597000 - 000000006d686000
>      >      (reserved)
>      >      >      >      >      >  Xen: 000000006f598000 - 000000006f59a000
>      >      (reserved)
>      >      >      >      >      >  Xen: 000000006f59a000 - 000000006f5af000
>      (ACPI
>      >      NVS)
>      >      >      >      >      >  Xen: 000000006f5af000 - 000000006f5d9000
>      >      (reserved)
>      >      >      >      >      >  Xen: 000000006f5d9000 - 000000006f5f9000
>      (ACPI
>      >      data)
>      >      >      >      >      >  Xen: 000000006f5f9000 - 000000006f6df000
>      (ACPI
>      >      NVS)
>      >      >      >      >      >  Xen: 000000006f6df000 - 000000006f700000
>      (ACPI
>      >      data)
>      >      >      >      >      >  Xen: 000000006f700000 - 0000000080000000
>      >      (reserved)
>      >      >      >      >      >  Xen: 00000000a0000000 - 00000000b0000000
>      >      (reserved)
>      >      >      >      >      >  Xen: 00000000fc000000 - 00000000fd000000
>      >      (reserved)
>      >      >      >      >      >  Xen: 00000000fed1c000 - 00000000fed20000
>      >      (reserved)
>      >      >      >      >      >  Xen: 00000000ffc00000 - 0000000100000000
>      >      (reserved)
>      >      >      >      >      > bootconsole [xenboot0] enabled
>      >      >      >      >      > DMI 2.4 present.
>      >      >      >      >      > last_pfn = 0x66c0a max_arch_pfn =
>      0x400000000
>      >      >      >      >      > init_memory_mapping:
>      >      0000000000000000-0000000066c0a000
>      >      >      >      >      > RAMDISK: 026bb000 - 02d0d800
>      >      >      >      >      > ACPI: RSDP 00000000000f03f0 00024 (v02
>      INTEL )
>      >      >      >      >      > ACPI: XSDT 000000006f6fe120 00064 (v01
>      INTEL
>      >       THRLY
>      >      >       00000000
>      >      >      >      >       01000013)
>      >      >      >      >      > ACPI: FACP 000000006f6fd000 000F4 (v04
>      INTEL
>      >       THRLY
>      >      >       00000000
>      >      >      >      MSFT
>      >      >      >      >      0100000D)
>      >      >      >      >      > ACPI: DSDT 000000006f6f5000 074F1 (v02
>      INTEL
>      >       THRLY
>      >      >       00000003
>      >      >      >      MSFT
>      >      >      >      >      0100000D)
>      >      >      >      >      > ACPI: FACS 000000006f5f9000 00040
>      >      >      >      >      > ACPI: APIC 000000006f6f4000 001CC (v02
>      INTEL
>      >       THRLY
>      >      >       00000000
>      >      >      >      MSFT
>      >      >      >      >      0100000D)
>      >      >      >      >      > ACPI: MCFG 000000006f6f3000 0003C (v01
>      INTEL
>      >       THRLY
>      >      >       00000001
>      >      >      >      MSFT
>      >      >      >      >      0100000D)
>      >      >      >      >      > ACPI: HPET 000000006f6f2000 00038 (v01
>      INTEL
>      >       THRLY
>      >      >       00000001
>      >      >      >      MSFT
>      >      >      >      >      0100000D)
>      >      >      >      >      > ACPI: SLIT 000000006f6f1000 00030 (v01
>      INTEL
>      >       THRLY
>      >      >       00000001
>      >      >      >      MSFT
>      >      >      >      >      0100000D)
>      >      >      >      >      > ACPI: WDDT 000000006f6f0000 00040 (v01
>      INTEL
>      >       THRLY
>      >      >       00000000
>      >      >      >      MSFT
>      >      >      >      >      0100000D)
>      >      >      >      >      > ACPI: SSDT 000000006f5d9000 1FDDC (v01
>       INTEL
>      >      SSDT  PM
>      >      >      00004000
>      >      >      >      INTL
>      >      >      >      >      20061109)
>      >      >      >      >      > ACPI:      000000006f6ee000 001D0 (v01
>      INTEL
>      >       THRLY
>      >      >       00000001
>      >      >      >      MSFT
>      >      >      >      >      0100000D)
>      >      >      >      >      > No NUMA configuration found
>      >      >      >      >      > Faking a node at
>      >      0000000000000000-0000000066c0a000
>      >      >      >      >      > Bootmem setup node 0
>      >      0000000000000000-0000000066c0a000
>      >      >      >      >      >   NODE_DATA [0000000000008000 -
>      000000000001ffff]
>      >      >      >      >      >   bootmap [0000000000020000 -
>       000000000002cd87]
>      >      pages d
>      >      >      >      >      > (9 early reservations) ==> bootmem
>      [0000000000 -
>      >      >      0066c0a000]
>      >      >      >      >      >   #0 [0000000000 - 0000001000]   BIOS data
>      page
>      >      ==>
>      >      >      [0000000000
>      >      >      >      -
>      >      >      >      >      0000001000]
>      >      >      >      >      >   #1 [0003046000 - 0003063000]   XEN
>      PAGETABLES
>      >      ==>
>      >      >      [0003046000
>      >      >      >      -
>      >      >      >      >      0003063000]
>      >      >      >      >      >   #2 [0000006000 - 0000008000]
>      TRAMPOLINE
>      >      ==>
>      >      >      [0000006000
>      >      >      >      -
>      >      >      >      >      0000008000]
>      >      >      >      >      >   #3 [0001000000 - 000269ae98]    TEXT
>      DATA BSS
>      >      ==>
>      >      >      [0001000000
>      >      >      >      -
>      >      >      >      >      000269ae98]
>      >      >      >      >      >   #4 [00026bb000 - 0002d0d800]
>       RAMDISK
>      >      ==>
>      >      >      [00026bb000
>      >      >      >      -
>      >      >      >      >      0002d0d800]
>      >      >      >      >      >   #5 [0002d0e000 - 0003046000]   XEN START
>      INFO
>      >      ==>
>      >      >      [0002d0e000
>      >      >      >      -
>      >      >      >      >      0003046000]
>      >      >      >      >      >   #6 [000269b000 - 000269b011]
>       BRK
>      >      ==>
>      >      >      [000269b000
>      >      >      >      -
>      >      >      >      >      000269b011]
>      >      >      >      >      >   #7 [0000100000 - 000041a000]
>       PGTABLE
>      >      ==>
>      >      >      [0000100000
>      >      >      >      -
>      >      >      >      >      000041a000]
>      >      >      >      >      >   #8 [0000001000 - 0000001030]        ACPI
>      SLIT
>      >      ==>
>      >      >      [0000001000
>      >      >      >      -
>      >      >      >      >      0000001030]
>      >      >      >      >      > found SMP MP-table at [ffff8800000fd750]
>      fd750
>      >      >      >      >      > Zone PFN ranges:
>      >      >      >      >      >   DMA      0x00000000 -> 0x00001000
>      >      >      >      >      >   DMA32    0x00001000 -> 0x00100000
>      >      >      >      >      >   Normal   0x00100000 -> 0x00100000
>      >      >      >      >      > Movable zone start PFN for each node
>      >      >      >      >      > early_node_map[2] active PFN ranges
>      >      >      >      >      >     0: 0x00000000 -> 0x0000009d
>      >      >      >      >      >     0: 0x00000100 -> 0x00066c0a
>      >      >      >      >      > ACPI: PM-Timer IO Port: 0x408
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00]
>      >      enabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02]
>      >      enabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04]
>      >      enabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x03] lapic_id[0x10]
>      >      enabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x04] lapic_id[0x12]
>      >      enabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14]
>      >      enabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x06] lapic_id[0x01]
>      >      enabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x07] lapic_id[0x03]
>      >      enabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x08] lapic_id[0x05]
>      >      enabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11]
>      >      enabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x13]
>      >      enabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x15]
>      >      enabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x0c] lapic_id[0xff]
>      >      disabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x0d] lapic_id[0xff]
>      >      disabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x0e] lapic_id[0xff]
>      >      disabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x0f] lapic_id[0xff]
>      >      disabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x10] lapic_id[0xff]
>      >      disabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x11] lapic_id[0xff]
>      >      disabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x12] lapic_id[0xff]
>      >      disabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x13] lapic_id[0xff]
>      >      disabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x14] lapic_id[0xff]
>      >      disabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x15] lapic_id[0xff]
>      >      disabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x16] lapic_id[0xff]
>      >      disabled)
>      >      >      >      >      > ACPI: LAPIC (acpi_id[0x17] lapic_id[0xff]
>      >      disabled)
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x00] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x01] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x02] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x03] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x04] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x05] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x06] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x07] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x08] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x09] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x0a] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x0b] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x0c] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x0d] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x0e] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x0f] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x10] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x11] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x12] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x13] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x14] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x15] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x16] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: LAPIC_NMI (acpi_id[0x17] high level
>      >      lint[0x1])
>      >      >      >      >      > ACPI: IOAPIC (id[0x08] address[0xfec00000]
>      >      gsi_base[0])
>      >      >      >      >      > IOAPIC[0]: apic_id 8, version 0, address
>      >      0xfec00000, GSI
>      >      >      0-0
>      >      >      >      >      > ACPI: IOAPIC (id[0x09] address[0xfec90000]
>      >      gsi_base[24])
>      >      >      >      >      > IOAPIC[1]: apic_id 9, version 0, address
>      >      0xfec90000, GSI
>      >      >      24-24
>      >      >      >      >      > ACPI: INT_SRC_OVR (bus 0 bus_irq 0
>      global_irq 2
>      >      dfl dfl)
>      >      >      >      >      > ERROR: Unable to locate IOAPIC for GSI 2
>      >      >      >      >      > ACPI: INT_SRC_OVR (bus 0 bus_irq 9
>      global_irq 9
>      >      high
>      >      >      level)
>      >      >      >      >      > ERROR: Unable to locate IOAPIC for GSI 9
>      >      >      >      >      > Using ACPI (MADT) for SMP configuration
>      >      information
>      >      >      >      >      > ACPI: HPET id: 0x8086a401 base: 0xfed00000
>      >      >      >      >      > SMP: Allowing 12 CPUs, 0 hotplug CPUs
>      >      >      >      >      > PM: Registered nosave memory:
>      000000000009d000 -
>      >      >      >      0000000000100000
>      >      >      >      >      > Allocating PCI resources starting at
>      b0000000
>      >      (gap:
>      >      >      >      b0000000:4c000000)
>      >      >      >      >      > Booting paravirtualized kernel on Xen
>      >      >      >      >      > Xen version: 3.4.3-rc4-pre (preserve-AD)
>      (dom0)
>      >      >      >      >      > NR_CPUS:512 nr_cpumask_bits:512
>      nr_cpu_ids:12
>      >      >      nr_node_ids:1
>      >      >      >      >      > PERCPU: Embedded 478 pages/cpu
>      @ffff880005ebc000
>      >      >      s1928024 r8192
>      >      >      >      d21672
>      >      >      >      >      u1957888
>      >      >      >      >      > pcpu-alloc: s1928024 r8192 d21672 u1957888
>      >      >      alloc=478*4096
>      >      >      >      >      > pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03
>      [0] 04
>      >      [0] 05
>      >      >      [0] 06
>      >      >      >      [0] 07
>      >      >      >      >      > pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11
>      >      >      >      >      > Xen: using vcpu_info placement
>      >      >      >      >      > Built 1 zonelists in Node order, mobility
>      >      grouping on.
>      >      >       Total
>      >      >      >      pages:
>      >      >      >      >      409291
>      >      >      >      >      > Policy zone: DMA32
>      >      >      >      >      > Kernel command line: ro
>      >      root=/dev/VolGroup01/LogVol00
>      >      >      >      console=hvc0
>      >      >      >      >      earlyprintk=xen nomodeset
>      >      >      >      >      > PID hash table entries: 4096 (order: 3,
>      32768
>      >      bytes)
>      >      >      >      >      > Initializing CPU#0
>      >      >      >      >      > DMA: Placing 64MB software IO TLB between
>      >      >      ffff880007525000 -
>      >      >      >      >      ffff88000b525000
>      >      >      >      >      > DMA: software IO TLB at phys 0x7525000 -
>      >      0xb525000
>      >      >      >      >      > xen_swiotlb_fixup: buf=ffff880007525000
>      >      size=67108864
>      >      >      >      >      > xen_swiotlb_fixup: buf=ffff88000b585000
>      >      size=32768
>      >      >      >      >      > Memory: 1514268k/1683496k available (4654k
>      kernel
>      >      code,
>      >      >      396k
>      >      >      >      absent,
>      >      >      >      >      168832k reserved, 3443k data, 3396k init)
>      >      >      >      >      > SLUB: Genslabs=14, HWalign=64, Order=0-3,
>      >      MinObjects=0,
>      >      >      >      CPUs=12,
>      >      >      >      >      Nodes=1
>      >      >      >      >      > Hierarchical RCU implementation.
>      >      >      >      >      > NR_IRQS:4352 nr_irqs:3072
>      >      >      >      >      > Already setup the GSI :0
>      >      >      >      >      > Already setup the GSI :1
>      >      >      >      >      > Already setup the GSI :2
>      >      >      >      >      > Already setup the GSI :3
>      >      >      >      >      > Already setup the GSI :4
>      >      >      >      >      > Already setup the GSI :5
>      >      >      >      >      > Already setup the GSI :6
>      >      >      >      >      > Already setup the GSI :7
>      >      >      >      >      > Already setup the GSI :8
>      >      >      >      >      > Already setup the GSI :9
>      >      >      >      >      > Already setup the GSI :10
>      >      >      >      >      > Already setup the GSI :11
>      >      >      >      >      > Already setup the GSI :12
>      >      >      >      >      > Already setup the GSI :13
>      >      >      >      >      > Already setup the GSI :14
>      >      >      >      >      > Already setup the GSI :15
>      >      >      >      >      > ACPI: INT_SRC_OVR (bus 0 bus_irq 0
>      global_irq 2
>      >      dfl dfl)
>      >      >      >      >      > ACPI: INT_SRC_OVR (bus 0 bus_irq 9
>      global_irq 9
>      >      high
>      >      >      level)
>      >      >      >      >      > xen: sci override: source_irq=9
>      global_irq=9
>      >      trigger=c
>      >      >      >      polarity=1
>      >      >      >      >      > xen_allocate_pirq: returning irq 9 for gsi
>      9
>      >      >      >      >      > Already setup the GSI :9
>      >      >      >      >      > xen: acpi sci 9
>      >      >      >      >      > Console: colour VGA+ 80x25
>      >      >      >      >      > console [hvc0] enabled, bootconsole
>      disabled
>      >      console
>      >      >      [hvc0]
>      >      >      >      enabled,
>      >      >      >      >      bootconsole disabled
>      >      >      >      >      > Lock dependency validator: Copyright (c)
>      2006 Red
>      >      Hat,
>      >      >      Inc.,
>      >      >      >      Ingo
>      >      >      >      >      Molnar ... MAX_LOCKDEP_SUBCLASSES:  8 ...
>      >      MAX_LOCK_DEPTH:
>      >      >      >       48
>      >      >      >      >      ... MAX_LOCKDEP_KEYS:        8191 ...
>      >      CLASSHASH_SIZE:
>      >      >      >       4096 ...
>      >      >      >      >      MAX_LOCKDEP_ENTRIES:     16384 ...
>      >      MAX_LOCKDEP_CHAINS:
>      >      >       32768
>      >      >      >      ...
>      >      >      >      >      CHAINHASH_SIZE:          16384  memory used
>      by lock
>      >      >      dependency
>      >      >      >      info:
>      >      >      >      >      6367 kB  per task-struct memory footprint:
>      2688
>      >      bytes
>      >      >      allocated
>      >      >      >      17039360
>      >      >      >      >      bytes of page_cgroup please try
>      >      'cgroup_disable=memory'
>      >      >      option if
>      >      >      >      you
>      >      >      >      >      don't want memory cgroups installing Xen
>      timer for
>      >      CPU 0
>      >      >      Detected
>      >      >      >      >      3200.206 MHz processor. Calibrating delay
>      loop
>      >      (skipped),
>      >      >      value
>      >      >      >      >      calculated using timer frequency.. 6400.41
>      BogoMIPS
>      >      >      (lpj=3200206)
>      >      >      >      >      Security Framework initialized SELinux:
>      >       Initializing.
>      >      >      Dentry
>      >      >      >      cache hash
>      >      >      >      >      table entries: 262144 (order: 9, 2097152
>      bytes)
>      >      >      Inode-cache hash
>      >      >      >      table
>      >      >      >      >      entries: 131072 (order: 8, 1048576 bytes)
>      >      Mount-cache hash
>      >      >      table
>      >      >      >      >      entries: 256 Initializing cgroup subsys ns
>      >      Initializing
>      >      >      cgroup
>      >      >      >      subsys
>      >      >      >      >      cpuacct Initializing cgroup subsys memory
>      >      Initializing
>      >      >      cgroup
>      >      >      >      subsys
>      >      >      >      >      devices Initializing cgroup subsys freezer
>      >      Initializing
>      >      >      cgroup
>      >      >      >      subsys
>      >      >      >      >      net_cls CPU: L1 I cache: 32K, L1 D cache:
>      32K CPU:
>      >      L2
>      >      >      cache: 256K
>      >      >      >      CPU:
>      >      >      >      >      L3 cache: 12288K CPU 0/0x0 -> Node 0 CPU:
>      >      Unsupported
>      >      >      number of
>      >      >      >      siblings
>      >      >      >      >      32 Performance Events: unsupported p6 CPU
>      model 44
>      >      no PMU
>      >      >      driver,
>      >      >      >      >      software events only. lockdep: fixing up
>      >      alternatives. SMP
>      >      >      >      alternatives:
>      >      >      >      >      switching to UP code ACPI: Core revision
>      20090903
>      >      ftrace:
>      >      >      >      converting
>      >      >      >      >      mcount calls to 0f 1f 44 00 00 ftrace:
>      allocating
>      >      27971
>      >      >      entries
>      >      >      >      in 110
>      >      >      >      >      pages installing Xen timer for CPU 1
>      lockdep:
>      >      fixing up
>      >      >      >      alternatives.
>      >      >      >      >      SMP alternatives: switching to SMP code
>      >      Initializing CPU#1
>      >      >      CPU:
>      >      >      >      L1 I
>      >      >      >      >      cache: 32K, L1 D cache: 32K CPU: L2 cache:
>      256K
>      >      CPU: L3
>      >      >      cache:
>      >      >      >      12288K
>      >      >      >      >      CPU 1/0x0 -> Node 0 CPU: Unsupported number
>      of
>      >      siblings 32
>      >      >      >      installing
>      >      >      >      >      Xen timer for CPU 2 Initializing CPU#2 CPU:
>      L1 I
>      >      cache:
>      >      >      32K, L1 D
>      >      >      >      cache:
>      >      >      >      >      32K CPU: L2 cache: 256K CPU: L3 cache:
>      12288K CPU
>      >      2/0x0 ->
>      >      >      Node 0
>      >      >      >      CPU:
>      >      >      >      >      Unsupported number of siblings 32 installing
>      Xen
>      >      timer for
>      >      >      CPU 3
>      >      >      >      >      Initializing CPU#3 CPU: L1 I cache: 32K, L1
>      D
>      >      cache: 32K
>      >      >      CPU: L2
>      >      >      >      cache:
>      >      >      >      >      256K CPU: L3 cache: 12288K CPU 3/0x0 -> Node
>      0 CPU:
>      >      >      Unsupported
>      >      >      >      number
>      >      >      >      >      of siblings 32 installing Xen timer for CPU
>      4
>      >      Initializing
>      >      >      CPU#4
>      >      >      >      CPU: L1
>      >      >      >      >      I cache: 32K, L1 D cache: 32K CPU: L2 cache:
>      256K
>      >      CPU: L3
>      >      >      cache:
>      >      >      >      12288K
>      >      >      >      >      CPU 4/0x0 -> Node 0 CPU: Unsupported number
>      of
>      >      siblings 32
>      >      >      >      installing
>      >      >      >      >      Xen timer for CPU 5 Initializing CPU#5 CPU:
>      L1 I
>      >      cache:
>      >      >      32K, L1 D
>      >      >      >      cache:
>      >      >      >      >      32K CPU: L2 cache: 256K CPU: L3 cache:
>      12288K CPU
>      >      5/0x0 ->
>      >      >      Node 0
>      >      >      >      CPU:
>      >      >      >      >      Unsupported number of siblings 32 installing
>      Xen
>      >      timer for
>      >      >      CPU 6
>      >      >      >      >      Initializing CPU#6 CPU: L1 I cache: 32K, L1
>      D
>      >      cache: 32K
>      >      >      CPU: L2
>      >      >      >      cache:
>      >      >      >      >      256K CPU: L3 cache: 12288K CPU 6/0x0 -> Node
>      0 CPU:
>      >      >      Unsupported
>      >      >      >      number
>      >      >      >      >      of siblings 32 installing Xen timer for CPU
>      7
>      >      Initializing
>      >      >      CPU#7
>      >      >      >      CPU: L1
>      >      >      >      >      I cache: 32K, L1 D cache: 32K CPU: L2 cache:
>      256K
>      >      CPU: L3
>      >      >      cache:
>      >      >      >      12288K
>      >      >      >      >      CPU 7/0x0 -> Node 0 CPU: Unsupported number
>      of
>      >      siblings 32
>      >      >      >      installing
>      >      >      >      >      Xen timer for CPU 8 Initializing CPU#8 CPU:
>      L1 I
>      >      cache:
>      >      >      32K, L1 D
>      >      >      >      cache:
>      >      >      >      >      32K CPU: L2 cache: 256K CPU: L3 cache:
>      12288K CPU
>      >      8/0x0 ->
>      >      >      Node 0
>      >      >      >      CPU:
>      >      >      >      >      Unsupported number of siblings 32 installing
>      Xen
>      >      timer for
>      >      >      CPU 9
>      >      >      >      >      Initializing CPU#9 CPU: L1 I cache: 32K, L1
>      D
>      >      cache: 32K
>      >      >      CPU: L2
>      >      >      >      cache:
>      >      >      >      >      256K CPU: L3 cache: 12288K CPU 9/0x0 -> Node
>      0 CPU:
>      >      >      Unsupported
>      >      >      >      number
>      >      >      >      >      of siblings 32 installing Xen timer for CPU
>      10
>      >      >      Initializing
>      >      >      >      CPU#10 CPU:
>      >      >      >      >      L1 I cache: 32K, L1 D cache: 32K CPU: L2
>      cache:
>      >      256K CPU:
>      >      >      L3
>      >      >      >      cache:
>      >      >      >      >      12288K CPU 10/0x0 -> Node 0 CPU: Unsupported
>      number
>      >      of
>      >      >      siblings
>      >      >      >      32
>      >      >      >      >      installing Xen timer for CPU 11 Initializing
>      CPU#11
>      >      CPU:
>      >      >      L1 I
>      >      >      >      cache:
>      >      >      >      >      32K, L1 D cache: 32K CPU: L2 cache: 256K
>      CPU: L3
>      >      cache:
>      >      >      12288K
>      >      >      >      CPU
>      >      >      >      >      11/0x0 -> Node 0 CPU: Unsupported number of
>      >      siblings 32
>      >      >      Brought
>      >      >      >      up 12
>      >      >      >      >      CPUs Grant table initialized regulator: core
>      >      version 0.5
>      >      >      Time:
>      >      >      >      14:45:00
>      >      >      >      >       Date: 03/16/10 NET: Registered protocol
>      family 16
>      >      >      >      xenbus_probe_init ok
>      >      >      >      >      ACPI FADT declares the system doesn't
>      support PCIe
>      >      ASPM,
>      >      >      so
>      >      >      >      disable it
>      >      >      >      >      ACPI: bus type pci registered PCI: MCFG
>      >      configuration 0:
>      >      >      base
>      >      >      >      a0000000
>      >      >      >      >      segment 0 buses 0 - 255 PCI: MCFG area at
>      a0000000
>      >      >      reserved in
>      >      >      >      E820 PCI:
>      >      >      >      >      Using MMCONFIG at a0000000 - afffffff PCI:
>      Using
>      >      >      configuration
>      >      >      >      type 1
>      >      >      >      >      for base access bio: create slab <bio-0> at
>      0 ACPI
>      >      Error:
>      >      >      Field
>      >      >      >      [CPB3]
>      >      >      >      >      at 96 exceeds Buffer [NULL] size 64 (bits)
>      >      >      >      (20090903/dsopcode-596) ACPI
>      >      >      >      >      Error (psparse-0537): Method parse/execution
>      failed
>      >      >      [\_SB_._OSC]
>      >      >      >      (Node
>      >      >      >      >      ffff880064e00c98), AE_AML_BUFFER_LIMIT ACPI:
>      >      Interpreter
>      >      >      enabled
>      >      >      >      ACPI:
>      >      >      >      >      (supports S0 S1 S3 S4 S5) ACPI: Using IOAPIC
>      for
>      >      interrupt
>      >      >      >      routing ACPI
>      >      >      >      >      Warning: Incorrect checksum in table [    ]
>      - 97,
>      >      should
>      >      >      be DB
>      >      >      >      >      (20090903/tbutils-314) ACPI: No dock devices
>      found.
>      >      ACPI:
>      >      >      PCI
>      >      >      >      Root
>      >      >      >      >      Bridge [PCI0] (0000:00) pci 0000:00:01.0:
>      PME#
>      >      supported
>      >      >      from D0
>      >      >      >      D3hot
>      >      >      >      >      D3cold pci 0000:00:01.0: PME# disabled pci
>      >      0000:00:02.0:
>      >      >      PME#
>      >      >      >      supported
>      >      >      >      >      from D0 D3hot D3cold pci 0000:00:02.0: PME#
>      >      disabled pci
>      >      >      >      0000:00:03.0:
>      >      >      >      >      PME# supported from D0 D3hot D3cold pci
>      >      0000:00:03.0: PME#
>      >      >      >      disabled pci
>      >      >      >      >      0000:00:04.0: PME# supported from D0 D3hot
>      D3cold
>      >      pci
>      >      >      >      0000:00:04.0: PME#
>      >      >      >      >      disabled pci 0000:00:05.0: PME# supported
>      from D0
>      >      D3hot
>      >      >      D3cold
>      >      >      >      pci
>      >      >      >      >      0000:00:05.0: PME# disabled pci
>      0000:00:06.0: PME#
>      >      >      supported from
>      >      >      >      D0
>      >      >      >      >      D3hot D3cold pci 0000:00:06.0: PME# disabled
>      pci
>      >      >      0000:00:07.0:
>      >      >      >      PME#
>      >      >      >      >      supported from D0 D3hot D3cold pci
>      0000:00:07.0:
>      >      PME#
>      >      >      disabled
>      >      >      >      pci
>      >      >      >      >      0000:00:08.0: PME# supported from D0 D3hot
>      D3cold
>      >      pci
>      >      >      >      0000:00:08.0: PME#
>      >      >      >      >      disabled pci 0000:00:09.0: PME# supported
>      from D0
>      >      D3hot
>      >      >      D3cold
>      >      >      >      pci
>      >      >      >      >      0000:00:09.0: PME# disabled pci
>      0000:00:0a.0: PME#
>      >      >      supported from
>      >      >      >      D0
>      >      >      >      >      D3hot D3cold pci 0000:00:0a.0: PME# disabled
>      pci
>      >      >      0000:00:13.0:
>      >      >      >      PME#
>      >      >      >      >      supported from D0 D3hot D3cold pci
>      0000:00:13.0:
>      >      PME#
>      >      >      disabled
>      >      >      >      pci
>      >      >      >      >      0000:00:1a.7: PME# supported from D0 D3hot
>      D3cold
>      >      pci
>      >      >      >      0000:00:1a.7: PME#
>      >      >      >      >      disabled pci 0000:00:1c.0: PME# supported
>      from D0
>      >      D3hot
>      >      >      D3cold
>      >      >      >      pci
>      >      >      >      >      0000:00:1c.0: PME# disabled pci
>      0000:00:1c.4: PME#
>      >      >      supported from
>      >      >      >      D0
>      >      >      >      >      D3hot D3cold pci 0000:00:1c.4: PME# disabled
>      pci
>      >      >      0000:00:1c.5:
>      >      >      >      PME#
>      >      >      >      >      supported from D0 D3hot D3cold pci
>      0000:00:1c.5:
>      >      PME#
>      >      >      disabled
>      >      >      >      pci
>      >      >      >      >      0000:00:1d.7: PME# supported from D0 D3hot
>      D3cold
>      >      pci
>      >      >      >      0000:00:1d.7: PME#
>      >      >      >      >      disabled pci 0000:00:1f.0: quirk: region
>      0400-047f
>      >      claimed
>      >      >      by
>      >      >      >      ICH6
>      >      >      >      >      ACPI/GPIO/TCO pci 0000:00:1f.0: quirk:
>      region
>      >      0500-053f
>      >      >      claimed
>      >      >      >      by ICH6
>      >      >      >      >      GPIO pci 0000:00:1f.0: ICH7 LPC Generic IO
>      decode 1
>      >      PIO at
>      >      >      0680
>      >      >      >      (mask
>      >      >      >      >      000f) pci 0000:00:1f.0: ICH7 LPC Generic IO
>      decode
>      >      2 PIO
>      >      >      at 0ca0
>      >      >      >      (mask
>      >      >      >      >      000f) pci 0000:00:1f.0: ICH7 LPC Generic IO
>      decode
>      >      3 PIO
>      >      >      at 0600
>      >      >      >      (mask
>      >      >      >      >      001f) pci 0000:00:1f.2: PME# supported from
>      D3hot
>      >      pci
>      >      >      >      0000:00:1f.2: PME#
>      >      >      >      >      disabled pci 0000:01:00.0: PME# supported
>      from D0
>      >      D3hot
>      >      >      D3cold
>      >      >      >      pci
>      >      >      >      >      0000:01:00.0: PME# disabled pci
>      0000:01:00.1: PME#
>      >      >      supported from
>      >      >      >      D0
>      >      >      >      >      D3hot D3cold pci 0000:01:00.1: PME# disabled
>      pci
>      >      >      0000:0c:00.0:
>      >      >      >      disabling
>      >      >      >      >      ASPM on pre-1.1 PCIe device.  You can enable
>      it
>      >      with
>      >      >      >      'pcie_aspm=force'
>      >      >      >      >      pci 0000:00:1e.0: transparent bridge ACPI:
>      PCI Root
>      >      Bridge
>      >      >      [PCI1]
>      >      >      >      >      (0000:fe) ACPI: PCI Root Bridge [PCI2]
>      (0000:ff)
>      >      ACPI: PCI
>      >      >      >      Interrupt
>      >      >      >      >      Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14
>      15)
>      >      ACPI: PCI
>      >      >      >      Interrupt Link
>      >      >      >      >      [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
>      ACPI: PCI
>      >      >      Interrupt
>      >      >      >      Link
>      >      >      >      >      [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
>      ACPI: PCI
>      >      >      Interrupt
>      >      >      >      Link
>      >      >      >      >      [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
>      ACPI: PCI
>      >      >      Interrupt
>      >      >      >      Link
>      >      >      >      >      [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
>      >      disabled.
>      >      >      ACPI: PCI
>      >      >      >      >      Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10
>      *11 12
>      >      14 15)
>      >      >      ACPI:
>      >      >      >      PCI
>      >      >      >      >      Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10
>      11 12 14
>      >      15)
>      >      >      *0,
>      >      >      >      disabled.
>      >      >      >      >      ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5
>      6 7 9
>      >      *10 11
>      >      >      12 14
>      >      >      >      15)
>      >      >      >      >      xenbus_probe_backend_init bus registered ok
>      >      >      >      xenbus_probe_frontend_init
>      >      >      >      >      bus registered ok xen_balloon: Initialising
>      balloon
>      >      driver
>      >      >      with
>      >      >      >      page
>      >      >      >      >      order 0. vgaarb: device added:
>      >      >      >      >
>      >       PCI:0000:0c:00.0,decodes=io+mem,owns=io+mem,locks=none
>      >      >      vgaarb:
>      >      >      >      loaded
>      >      >      >      >      SCSI subsystem initialized usbcore:
>      registered new
>      >      >      interface
>      >      >      >      driver
>      >      >      >      >      usbfs usbcore: registered new interface
>      driver hub
>      >      >      usbcore:
>      >      >      >      registered
>      >      >      >      >      new device driver usb PCI: Using ACPI for
>      IRQ
>      >      routing
>      >      >      NetLabel:
>      >      >      >      >      Initializing NetLabel:  domain hash size =
>      128
>      >      NetLabel:
>      >      >      >       protocols =
>      >      >      >      >      UNLABELED CIPSOv4 NetLabel:  unlabeled
>      traffic
>      >      allowed by
>      >      >      default
>      >      >      >      >      Switching to clocksource xen kstop/0 used
>      greatest
>      >      stack
>      >      >      depth:
>      >      >      >      6568
>      >      >      >      >      bytes left kstop/1 used greatest stack
>      depth: 6536
>      >      bytes
>      >      >      left
>      >      >      >      pnp: PnP
>      >      >      >      >      ACPI init ACPI: bus type pnp registered
>      >      xen_allocate_pirq:
>      >      >      >      returning irq
>      >      >      >      >      8 for gsi 8 Already setup the GSI :8
>      >      xen_allocate_pirq:
>      >      >      returning
>      >      >      >      irq 13
>      >      >      >      >      for gsi 13 Already setup the GSI :13 pnp:
>      PnP ACPI:
>      >      found
>      >      >      13
>      >      >      >      devices
>      >      >      >      >      ACPI: ACPI bus type pnp unregistered system
>      00:07:
>      >      ioport
>      >      >      range
>      >      >      >      >      0x500-0x53f has been reserved system 00:07:
>      ioport
>      >      range
>      >      >      >      0x400-0x47f has
>      >      >      >      >      been reserved system 00:07: ioport range
>      >      0x800-0x81f has
>      >      >      been
>      >      >      >      reserved
>      >      >      >      >      system 00:07: ioport range 0x2f8-0x2ff has
>      been
>      >      reserved
>      >      >      system
>      >      >      >      00:07:
>      >      >      >      >      iomem range 0xfed1c000-0xfed8bffe could not
>      be
>      >      reserved
>      >      >      system
>      >      >      >      00:07:
>      >      >      >      >      iomem range 0xff000000-0xffffffff could not
>      be
>      >      reserved
>      >      >      system
>      >      >      >      00:07:
>      >      >      >      >      iomem range 0xfee00000-0xfeefffff has been
>      reserved
>      >      system
>      >      >      00:07:
>      >      >      >      iomem
>      >      >      >      >      range 0xfe900000-0xfe90001f has been
>      reserved
>      >      system
>      >      >      00:07: iomem
>      >      >      >      range
>      >      >      >      >      0xfea00000-0xfea0001f has been reserved
>      system
>      >      00:07:
>      >      >      iomem range
>      >      >      >      >      0xfed1b000-0xfed1bfff has been reserved pci
>      >      0000:0c:00.0:
>      >      >      BAR 6:
>      >      >      >      no
>      >      >      >      >      parent found for of device
>      [0xffff0000-0xffffffff]
>      >      pci
>      >      >      >      0000:00:01.0: PCI
>      >      >      >      >      bridge, secondary bus 0000:01 pci
>      0000:00:01.0:
>      >      IO
>      >      >      window:
>      >      >      >      >      0x1000-0x1fff pci 0000:00:01.0:   MEM
>      window:
>      >      >      >      0xb1900000-0xb19fffff pci
>      >      >      >      >      0000:00:01.0:   PREFETCH window: disabled
>      pci
>      >      >      0000:00:02.0: PCI
>      >      >      >      bridge,
>      >      >      >      >      secondary bus 0000:02 pci 0000:00:02.0:   IO
>      >      window:
>      >      >      disabled pci
>      >      >      >      >      0000:00:02.0:   MEM window: disabled pci
>      >      0000:00:02.0:
>      >      >      PREFETCH
>      >      >      >      >      window: disabled pci 0000:00:03.0: PCI
>      bridge,
>      >      secondary
>      >      >      bus
>      >      >      >      0000:03 pci
>      >      >      >      >      0000:00:03.0:   IO window: disabled pci
>      >      0000:00:03.0:
>      >      >      MEM
>      >      >      >      window:
>      >      >      >      >      disabled pci 0000:00:03.0:   PREFETCH
>      window:
>      >      disabled pci
>      >      >      >      0000:00:04.0:
>      >      >      >      >      PCI bridge, secondary bus 0000:04 pci
>      0000:00:04.0:
>      >        IO
>      >      >      window:
>      >      >      >      >      disabled pci 0000:00:04.0:   MEM window:
>      disabled
>      >      pci
>      >      >      >      0000:00:04.0:
>      >      >      >      >      PREFETCH window: disabled pci 0000:00:05.0:
>      PCI
>      >      bridge,
>      >      >      secondary
>      >      >      >      bus
>      >      >      >      >      0000:05 pci 0000:00:05.0:   IO window:
>      disabled pci
>      >      >      0000:00:05.0:
>      >      >      >        MEM
>      >      >      >      >      window: disabled pci 0000:00:05.0:
>      PREFETCH
>      >      window:
>      >      >      disabled
>      >      >      >      pci
>      >      >      >      >      0000:00:06.0: PCI bridge, secondary bus
>      0000:06 pci
>      >      >      0000:00:06.0:
>      >      >      >        IO
>      >      >      >      >      window: disabled pci 0000:00:06.0:   MEM
>      window:
>      >      disabled
>      >      >      pci
>      >      >      >      >      0000:00:06.0:   PREFETCH window: disabled
>      pci
>      >      >      0000:00:07.0: PCI
>      >      >      >      bridge,
>      >      >      >      >      secondary bus 0000:07 pci 0000:00:07.0:   IO
>      >      window:
>      >      >      disabled pci
>      >      >      >      >      0000:00:07.0:   MEM window: disabled pci
>      >      0000:00:07.0:
>      >      >      PREFETCH
>      >      >      >      >      window: disabled pci 0000:00:08.0: PCI
>      bridge,
>      >      secondary
>      >      >      bus
>      >      >      >      0000:08 pci
>      >      >      >      >      0000:00:08.0:   IO window: disabled pci
>      >      0000:00:08.0:
>      >      >      MEM
>      >      >      >      window:
>      >      >      >      >      disabled pci 0000:00:08.0:   PREFETCH
>      window:
>      >      disabled pci
>      >      >      >      0000:00:09.0:
>      >      >      >      >      PCI bridge, secondary bus 0000:09 pci
>      0000:00:09.0:
>      >        IO
>      >      >      window:
>      >      >      >      >      0x3000-0x3fff pci 0000:00:09.0:   MEM
>      window:
>      >      >      >      0xb1b00000-0xb1cfffff pci
>      >      >      >      >      0000:00:09.0:   PREFETCH window:
>      >      >      >      0x000000b1d00000-0x000000b1efffff pci
>      >      >      >      >      0000:00:0a.0: PCI bridge, secondary bus
>      0000:0a pci
>      >      >      0000:00:0a.0:
>      >      >      >        IO
>      >      >      >      >      window: disabled pci 0000:00:0a.0:   MEM
>      window:
>      >      disabled
>      >      >      pci
>      >      >      >      >      0000:00:0a.0:   PREFETCH window: disabled
>      pci
>      >      >      0000:00:1c.0: PCI
>      >      >      >      bridge,
>      >      >      >      >      secondary bus 0000:0b pci 0000:00:1c.0:   IO
>      >      window:
>      >      >      disabled pci
>      >      >      >      >      0000:00:1c.0:   MEM window: disabled pci
>      >      0000:00:1c.0:
>      >      >      PREFETCH
>      >      >      >      >      window: disabled pci 0000:00:1c.4: PCI
>      bridge,
>      >      secondary
>      >      >      bus
>      >      >      >      0000:0c pci
>      >      >      >      >      0000:00:1c.4:   IO window: disabled pci
>      >      0000:00:1c.4:
>      >      >      MEM
>      >      >      >      window:
>      >      >      >      >      0xb1000000-0xb18fffff pci 0000:00:1c.4:
>      PREFETCH
>      >      window:
>      >      >      >      >      0x000000b0000000-0x000000b0ffffff pci
>      0000:00:1c.5:
>      >      PCI
>      >      >      bridge,
>      >      >      >      >      secondary bus 0000:0d pci 0000:00:1c.5:   IO
>      >      window:
>      >      >      disabled pci
>      >      >      >      >      0000:00:1c.5:   MEM window: disabled pci
>      >      0000:00:1c.5:
>      >      >      PREFETCH
>      >      >      >      >      window: disabled pci 0000:00:1e.0: PCI
>      bridge,
>      >      secondary
>      >      >      bus
>      >      >      >      0000:0e pci
>      >      >      >      >      0000:00:1e.0:   IO window: disabled pci
>      >      0000:00:1e.0:
>      >      >      MEM
>      >      >      >      window:
>      >      >      >      >      disabled pci 0000:00:1e.0:   PREFETCH
>      window:
>      >      disabled pci
>      >      >      >      0000:00:01.0:
>      >      >      >      >      PCI INT A -> GSI 28 (level, low) -> IRQ 28
>      pci
>      >      >      0000:00:02.0: PCI
>      >      >      >      INT A
>      >      >      >      >      -> GSI 29 (level, low) -> IRQ 29 pci
>      0000:00:03.0:
>      >      PCI INT
>      >      >      A ->
>      >      >      >      GSI 24
>      >      >      >      >      (level, low) -> IRQ 24 pci 0000:00:04.0: PCI
>      INT A
>      >      -> GSI
>      >      >      25
>      >      >      >      (level,
>      >      >      >      >      low) -> IRQ 25 pci 0000:00:05.0: PCI INT A
>      -> GSI
>      >      26
>      >      >      (level, low)
>      >      >      >      -> IRQ
>      >      >      >      >      26 pci 0000:00:06.0: PCI INT A -> GSI 27
>      (level,
>      >      low) ->
>      >      >      IRQ 27
>      >      >      >      pci
>      >      >      >      >      0000:00:07.0: PCI INT A -> GSI 30 (level,
>      low) ->
>      >      IRQ 30
>      >      >      pci
>      >      >      >      >      0000:00:08.0: PCI INT A -> GSI 31 (level,
>      low) ->
>      >      IRQ 31
>      >      >      pci
>      >      >      >      >      0000:00:09.0: PCI INT A -> GSI 32 (level,
>      low) ->
>      >      IRQ 32
>      >      >      pci
>      >      >      >      >      0000:00:0a.0: PCI INT A -> GSI 33 (level,
>      low) ->
>      >      IRQ 33
>      >      >      pci
>      >      >      >      >      0000:00:1c.0: PCI INT A -> GSI 16 (level,
>      low) ->
>      >      IRQ 16
>      >      >      >      >      xen_allocate_pirq: returning irq 16 for gsi
>      16
>      >      Already
>      >      >      setup the
>      >      >      >      GSI :16
>      >      >      >      >      pci 0000:00:1c.4: PCI INT A -> GSI 16
>      (level, low)
>      >      -> IRQ
>      >      >      16 pci
>      >      >      >      >      0000:00:1c.5: PCI INT B -> GSI 17 (level,
>      low) ->
>      >      IRQ 17
>      >      >      NET:
>      >      >      >      Registered
>      >      >      >      >      protocol family 2 IP route cache hash table
>      >      entries: 65536
>      >      >      >      (order: 7,
>      >      >      >      >      524288 bytes) TCP established hash table
>      entries:
>      >      262144
>      >      >      (order:
>      >      >      >      10,
>      >      >      >      >      4194304 bytes) TCP bind hash table entries:
>      65536
>      >      (order:
>      >      >      10,
>      >      >      >      4718592
>      >      >      >      >      bytes) TCP: Hash tables configured
>      (established
>      >      262144
>      >      >      bind
>      >      >      >      65536) TCP
>      >      >      >      >      reno registered NET: Registered protocol
>      family 1
>      >      pci
>      >      >      >      0000:01:00.0:
>      >      >      >      >      Disabling L0s pci 0000:01:00.1: Disabling
>      L0s
>      >      Trying to
>      >      >      unpack
>      >      >      >      rootfs
>      >      >      >      >      image as initramfs... Freeing initrd memory:
>      6474k
>      >      freed
>      >      >      DMA-API:
>      >      >      >      >      preallocated 32768 debug entries DMA-API:
>      debugging
>      >      >      enabled by
>      >      >      >      kernel
>      >      >      >      >      config PCI-DMA: Using software bounce
>      buffering for
>      >      IO
>      >      >      (SWIOTLB)
>      >      >      >      DMA:
>      >      >      >      >      Placing 64MB software IO TLB between
>      >      ffff880007525000 -
>      >      >      >      ffff88000b525000
>      >      >      >      >      DMA: software IO TLB at phys 0x7525000 -
>      0xb525000
>      >      audit:
>      >      >      >      initializing
>      >      >      >      >      netlink socket (disabled) type=2000
>      >      >      audit(1268750702.035:1):
>      >      >      >      initialized
>      >      >      >      >      HugeTLB registered 2 MB page size,
>      pre-allocated 0
>      >      pages
>      >      >      VFS:
>      >      >      >      Disk
>      >      >      >      >      quotas dquot_6.5.2 Dquot-cache hash table
>      entries:
>      >      512
>      >      >      (order 0,
>      >      >      >      4096
>      >      >      >      >      bytes) msgmni has been set to 2970
>      cryptomgr_test
>      >      used
>      >      >      greatest
>      >      >      >      stack
>      >      >      >      >      depth: 5864 bytes left cryptomgr_test used
>      greatest
>      >      stack
>      >      >      depth:
>      >      >      >      5816
>      >      >      >      >      bytes left alg: No test for stdrng (krng)
>      Block
>      >      layer SCSI
>      >      >      >      generic (bsg)
>      >      >      >      >      driver version 0.4 loaded (major 252) io
>      scheduler
>      >      noop
>      >      >      >      registered io
>      >      >      >      >      scheduler anticipatory registered io
>      scheduler
>      >      deadline
>      >      >      >      registered io
>      >      >      >      >      scheduler cfq registered (default)
>      pci_hotplug: PCI
>      >      Hot
>      >      >      Plug PCI
>      >      >      >      Core
>      >      >      >      >      version: 0.5 pciehp 0000:00:09.0:pcie04: HPC
>      >      vendor_id
>      >      >      8086
>      >      >      >      device_id
>      >      >      >      >      3410 ss_vid 0 ss_did 0 pciehp: PCI Express
>      Hot Plug
>      >      >      Controller
>      >      >      >      Driver
>      >      >      >      >      version: 0.4 acpiphp: ACPI Hot Plug PCI
>      Controller
>      >      Driver
>      >      >      >      version: 0.5
>      >      >      >      >      acpiphp_glue: Slot 2 already registered by
>      another
>      >      hotplug
>      >      >      driver
>      >      >      >      >      acpiphp_glue: Slot 2 already registered by
>      another
>      >      hotplug
>      >      >      driver
>      >      >      >      >      acpiphp_glue: Slot 2 already registered by
>      another
>      >      hotplug
>      >      >      driver
>      >      >      >      >      acpiphp_glue: Slot 2 already registered by
>      another
>      >      hotplug
>      >      >      driver
>      >      >      >      >      acpiphp_glue: Slot 2 already registered by
>      another
>      >      hotplug
>      >      >      driver
>      >      >      >      >      acpiphp_glue: Slot 2 already registered by
>      another
>      >      hotplug
>      >      >      driver
>      >      >      >      >      acpiphp_glue: Slot 2 already registered by
>      another
>      >      hotplug
>      >      >      driver
>      >      >      >      >      acpiphp_glue: Slot 2 already registered by
>      another
>      >      hotplug
>      >      >      driver
>      >      >      >      >      pci-stub: invalid id string "" input: Sleep
>      Button
>      >      as
>      >      >      >      >
>      >       /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
>      >      >      ACPI:
>      >      >      >      Sleep
>      >      >      >      >      Button [SLPB] input: Power Button as
>      >      >      >      >
>       /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 ACPI:
>      >      Power
>      >      >      Button
>      >      >      >      [PWRF]
>      >      >      >      >      registering netback hpet_acpi_add: no
>      address or
>      >      irqs in
>      >      >      _CRS
>      >      >      >      >      Non-volatile memory driver v1.3 Linux
>      agpgart
>      >      interface
>      >      >      v0.103
>      >      >      >      Serial:
>      >      >      >      >      8250/16550 driver, 4 ports, IRQ sharing
>      enabled
>      >      >      serial8250: ttyS1
>      >      >      >      at I/O
>      >      >      >      >      0x2f8 (irq = 3) is a 16550A brd: module
>      loaded
>      >      loop:
>      >      >      module
>      >      >      >      loaded
>      >      >      >      >      input: Macintosh mouse button emulation as
>      >      >      >      /devices/virtual/input/input2
>      >      >      >      >      ahci 0000:00:1f.2: PCI INT A -> GSI 19
>      (level, low)
>      >      -> IRQ
>      >      >      19
>      >      >      >      ahci
>      >      >      >      >      0000:00:1f.2: AHCI 0001.0200 32 slots 6
>      ports 3
>      >      Gbps 0x3f
>      >      >      impl
>      >      >      >      SATA mode
>      >      >      >      >      ahci 0000:00:1f.2: flags: 64bit ncq sntf pm
>      led clo
>      >      pio
>      >      >      slum part
>      >      >      >      ccc
>      >      >      >      >      ems  scsi0 : ahci scsi1 : ahci scsi2 : ahci
>      scsi3 :
>      >      ahci
>      >      >      scsi4 :
>      >      >      >      ahci
>      >      >      >      >      scsi5 : ahci ata1: SATA max UDMA/133
>      irq_stat
>      >      0x00400040,
>      >      >      >      connection
>      >      >      >      >      status changed irq 2996 ata2: SATA max
>      UDMA/133
>      >      abar
>      >      >      >      m2048@0xb1a00000
>      >      >      >      >      port 0xb1a00180 irq 2996 ata3: SATA max
>      UDMA/133
>      >      abar
>      >      >      >      m2048@0xb1a00000
>      >      >      >      >      port 0xb1a00200 irq 2996 ata4: SATA max
>      UDMA/133
>      >      abar
>      >      >      >      m2048@0xb1a00000
>      >      >      >      >      port 0xb1a00280 irq 2996 ata5: SATA max
>      UDMA/133
>      >      abar
>      >      >      >      m2048@0xb1a00000
>      >      >      >      >      port 0xb1a00300 irq 2996 ata6: SATA max
>      UDMA/133
>      >      abar
>      >      >      >      m2048@0xb1a00000
>      >      >      >      >      port 0xb1a00380 irq 2996 Fixed MDIO Bus:
>      probed
>      >      ehci_hcd:
>      >      >      USB 2.0
>      >      >      >      >      'Enhanced' Host Controller (EHCI) Driver
>      ehci_hcd
>      >      >      0000:00:1a.7:
>      >      >      >      PCI INT
>      >      >      >      >      C -> GSI 18 (level, low) -> IRQ 18 ehci_hcd
>      >      0000:00:1a.7:
>      >      >      EHCI
>      >      >      >      Host
>      >      >      >      >      Controller ehci_hcd 0000:00:1a.7: new USB
>      bus
>      >      registered,
>      >      >      >      assigned bus
>      >      >      >      >      number 1 ehci_hcd 0000:00:1a.7: debug port 1
>      >      ehci_hcd
>      >      >      >      0000:00:1a.7: irq
>      >      >      >      >      18, io mem 0xb1a02000 ehci_hcd 0000:00:1a.7:
>      USB
>      >      2.0
>      >      >      started,
>      >      >      >      EHCI 1.00
>      >      >      >      >      usb usb1: New USB device found,
>      idVendor=1d6b,
>      >      >      idProduct=0002 usb
>      >      >      >      usb1:
>      >      >      >      >      New USB device strings: Mfr=3, Product=2,
>      >      SerialNumber=1
>      >      >      usb
>      >      >      >      usb1:
>      >      >      >      >      Product: EHCI Host Controller usb usb1:
>      >      Manufacturer:
>      >      >      Linux
>      >      >      >      2.6.32.9
>      >      >      >      >      ehci_hcd usb usb1: SerialNumber:
>      0000:00:1a.7 usb
>      >      usb1:
>      >      >      >      configuration #1
>      >      >      >      >      chosen from 1 choice hub 1-0:1.0: USB hub
>      found hub
>      >      >      1-0:1.0: 6
>      >      >      >      ports
>      >      >      >      >      detected ehci_hcd 0000:00:1d.7: PCI INT A ->
>      GSI 23
>      >      >      (level, low)
>      >      >      >      -> IRQ
>      >      >      >      >      23 ehci_hcd 0000:00:1d.7: EHCI Host
>      Controller
>      >      ehci_hcd
>      >      >      >      0000:00:1d.7:
>      >      >      >      >      new USB bus registered, assigned bus number
>      2
>      >      ehci_hcd
>      >      >      >      0000:00:1d.7:
>      >      >      >      >      debug port 1 ehci_hcd 0000:00:1d.7: irq 23,
>      io mem
>      >      >      0xb1a01000
>      >      >      >      ehci_hcd
>      >      >      >      >      0000:00:1d.7: USB 2.0 started, EHCI 1.00 usb
>      usb2:
>      >      New USB
>      >      >      device
>      >      >      >      found,
>      >      >      >      >      idVendor=1d6b, idProduct=0002 usb usb2: New
>      USB
>      >      device
>      >      >      strings:
>      >      >      >      Mfr=3,
>      >      >      >      >      Product=2, SerialNumber=1 usb usb2: Product:
>      EHCI
>      >      Host
>      >      >      Controller
>      >      >      >      usb
>      >      >      >      >      usb2: Manufacturer: Linux 2.6.32.9 ehci_hcd
>      usb
>      >      usb2:
>      >      >      >      SerialNumber:
>      >      >      >      >      0000:00:1d.7 usb usb2: configuration #1
>      chosen from
>      >      1
>      >      >      choice hub
>      >      >      >      >      2-0:1.0: USB hub found hub 2-0:1.0: 6 ports
>      >      detected
>      >      >      ohci_hcd:
>      >      >      >      USB 1.1
>      >      >      >      >      'Open' Host Controller (OHCI) Driver
>      uhci_hcd: USB
>      >      >      Universal Host
>      >      >      >      >      Controller Interface driver
>      xen_allocate_pirq:
>      >      returning
>      >      >      irq 16
>      >      >      >      for gsi
>      >      >      >      >      16 Already setup the GSI :16 uhci_hcd
>      0000:00:1a.0:
>      >      PCI
>      >      >      INT A ->
>      >      >      >      GSI 16
>      >      >      >      >      (level, low) -> IRQ 16 uhci_hcd
>      0000:00:1a.0: UHCI
>      >      Host
>      >      >      >      Controller
>      >      >      >      >      uhci_hcd 0000:00:1a.0: new USB bus
>      registered,
>      >      assigned
>      >      >      bus
>      >      >      >      number 3
>      >      >      >      >      uhci_hcd 0000:00:1a.0: irq 16, io base
>      0x000020e0
>      >      usb
>      >      >      usb3: New
>      >      >      >      USB
>      >      >      >      >      device found, idVendor=1d6b, idProduct=0001
>      usb
>      >      usb3: New
>      >      >      USB
>      >      >      >      device
>      >      >      >      >      strings: Mfr=3, Product=2, SerialNumber=1
>      usb usb3:
>      >      >      Product: UHCI
>      >      >      >      Host
>      >      >      >      >      Controller usb usb3: Manufacturer: Linux
>      2.6.32.9
>      >      uhci_hcd
>      >      >      usb
>      >      >      >      usb3:
>      >      >      >      >      SerialNumber: 0000:00:1a.0 usb usb3:
>      configuration
>      >      #1
>      >      >      chosen from
>      >      >      >      1
>      >      >      >      >      choice hub 3-0:1.0: USB hub found hub
>      3-0:1.0: 2
>      >      ports
>      >      >      detected
>      >      >      >      uhci_hcd
>      >      >      >      >      0000:00:1a.1: PCI INT B -> GSI 21 (level,
>      low) ->
>      >      IRQ 21
>      >      >      uhci_hcd
>      >      >      >      >      0000:00:1a.1: UHCI Host Controller uhci_hcd
>      >      0000:00:1a.1:
>      >      >      new USB
>      >      >      >      bus
>      >      >      >      >      registered, assigned bus number 4 uhci_hcd
>      >      0000:00:1a.1:
>      >      >      irq 21,
>      >      >      >      io base
>      >      >      >      >      0x000020c0 usb usb4: New USB device found,
>      >      idVendor=1d6b,
>      >      >      >      idProduct=0001
>      >      >      >      >      usb usb4: New USB device strings: Mfr=3,
>      Product=2,
>      >      >      >      SerialNumber=1 usb
>      >      >      >      >      usb4: Product: UHCI Host Controller usb
>      usb4:
>      >      >      Manufacturer: Linux
>      >      >      >      >      2.6.32.9 uhci_hcd usb usb4: SerialNumber:
>      >      0000:00:1a.1 usb
>      >      >      usb4:
>      >      >      >      >      configuration #1 chosen from 1 choice hub
>      4-0:1.0:
>      >      USB hub
>      >      >      found
>      >      >      >      hub
>      >      >      >      >      4-0:1.0: 2 ports detected xen_allocate_pirq:
>      >      returning irq
>      >      >      19 for
>      >      >      >      gsi 19
>      >      >      >      >      Already setup the GSI :19 uhci_hcd
>      0000:00:1a.2:
>      >      PCI INT D
>      >      >      -> GSI
>      >      >      >      19
>      >      >      >      >      (level, low) -> IRQ 19 uhci_hcd
>      0000:00:1a.2: UHCI
>      >      Host
>      >      >      >      Controller
>      >      >      >      >      uhci_hcd 0000:00:1a.2: new USB bus
>      registered,
>      >      assigned
>      >      >      bus
>      >      >      >      number 5
>      >      >      >      >      uhci_hcd 0000:00:1a.2: irq 19, io base
>      0x000020a0
>      >      usb
>      >      >      usb5: New
>      >      >      >      USB
>      >      >      >      >      device found, idVendor=1d6b, idProduct=0001
>      usb
>      >      usb5: New
>      >      >      USB
>      >      >      >      device
>      >      >      >      >      strings: Mfr=3, Product=2, SerialNumber=1
>      usb usb5:
>      >      >      Product: UHCI
>      >      >      >      Host
>      >      >      >      >      Controller usb usb5: Manufacturer: Linux
>      2.6.32.9
>      >      uhci_hcd
>      >      >      usb
>      >      >      >      usb5:
>      >      >      >      >      SerialNumber: 0000:00:1a.2 usb usb5:
>      configuration
>      >      #1
>      >      >      chosen from
>      >      >      >      1
>      >      >      >      >      choice hub 5-0:1.0: USB hub found hub
>      5-0:1.0: 2
>      >      ports
>      >      >      detected
>      >      >      >      >      xen_allocate_pirq: returning irq 23 for gsi
>      23
>      >      Already
>      >      >      setup the
>      >      >      >      GSI :23
>      >      >      >      >      uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23
>      (level,
>      >      low) ->
>      >      >      IRQ 23
>      >      >      >      >      uhci_hcd 0000:00:1d.0: UHCI Host Controller
>      >      uhci_hcd
>      >      >      >      0000:00:1d.0: new
>      >      >      >      >      USB bus registered, assigned bus number 6
>      uhci_hcd
>      >      >      0000:00:1d.0:
>      >      >      >      irq 23,
>      >      >      >      >      io base 0x00002080 usb usb6: New USB device
>      found,
>      >      >      idVendor=1d6b,
>      >      >      >      >      idProduct=0001 usb usb6: New USB device
>      strings:
>      >      Mfr=3,
>      >      >      >      Product=2,
>      >      >      >      >      SerialNumber=1 usb usb6: Product: UHCI Host
>      >      Controller usb
>      >      >      usb6:
>      >      >      >      >      Manufacturer: Linux 2.6.32.9 uhci_hcd usb
>      usb6:
>      >      >      SerialNumber:
>      >      >      >      >      0000:00:1d.0 usb usb6: configuration #1
>      chosen from
>      >      1
>      >      >      choice hub
>      >      >      >      >      6-0:1.0: USB hub found hub 6-0:1.0: 2 ports
>      >      detected
>      >      >      >      xen_allocate_pirq:
>      >      >      >      >      returning irq 19 for gsi 19 Already setup
>      the GSI
>      >      :19
>      >      >      uhci_hcd
>      >      >      >      >      0000:00:1d.1: PCI INT B -> GSI 19 (level,
>      low) ->
>      >      IRQ 19
>      >      >      uhci_hcd
>      >      >      >      >      0000:00:1d.1: UHCI Host Controller uhci_hcd
>      >      0000:00:1d.1:
>      >      >      new USB
>      >      >      >      bus
>      >      >      >      >      registered, assigned bus number 7 uhci_hcd
>      >      0000:00:1d.1:
>      >      >      irq 19,
>      >      >      >      io base
>      >      >      >      >      0x00002060 usb usb7: New USB device found,
>      >      idVendor=1d6b,
>      >      >      >      idProduct=0001
>      >      >      >      >      usb usb7: New USB device strings: Mfr=3,
>      Product=2,
>      >      >      >      SerialNumber=1 usb
>      >      >      >      >      usb7: Product: UHCI Host Controller usb
>      usb7:
>      >      >      Manufacturer: Linux
>      >      >      >      >      2.6.32.9 uhci_hcd usb usb7: SerialNumber:
>      >      0000:00:1d.1 usb
>      >      >      usb7:
>      >      >      >      >      configuration #1 chosen from 1 choice hub
>      7-0:1.0:
>      >      USB hub
>      >      >      found
>      >      >      >      hub
>      >      >      >      >      7-0:1.0: 2 ports detected xen_allocate_pirq:
>      >      returning irq
>      >      >      18 for
>      >      >      >      gsi 18
>      >      >      >      >      Already setup the GSI :18 uhci_hcd
>      0000:00:1d.2:
>      >      PCI INT C
>      >      >      -> GSI
>      >      >      >      18
>      >      >      >      >      (level, low) -> IRQ 18 uhci_hcd
>      0000:00:1d.2: UHCI
>      >      Host
>      >      >      >      Controller
>      >      >      >      >      uhci_hcd 0000:00:1d.2: new USB bus
>      registered,
>      >      assigned
>      >      >      bus
>      >      >      >      number 8
>      >      >      >      >      uhci_hcd 0000:00:1d.2: irq 18, io base
>      0x00002040
>      >      usb
>      >      >      usb8: New
>      >      >      >      USB
>      >      >      >      >      device found, idVendor=1d6b, idProduct=0001
>      usb
>      >      usb8: New
>      >      >      USB
>      >      >      >      device
>      >      >      >      >      strings: Mfr=3, Product=2, SerialNumber=1
>      usb usb8:
>      >      >      Product: UHCI
>      >      >      >      Host
>      >      >
>      >
>      > References
>      >
>      >    Visible links
>      >    1. mailto:[20]pasik@xxxxxx
>      >    2. mailto:[21]pasik@xxxxxx
>      >    3. mailto:[22]pasik@xxxxxx
>      >    4. mailto:[23]pasik@xxxxxx
>      >    5. mailto:[24]pasik@xxxxxx
>      >    6.
>      [25]http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>      >    7.
>      
> [26]http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>      >    8. mailto:[27]pasik@xxxxxx
>      >    9.
>      [28]http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>      >   10.
>      
> [29]http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>      >   11. mailto:[30]pasik@xxxxxx
>      >   12. mailto:[31]pasik@xxxxxx
>      >   13.
>      [32]http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>      >   14.
>      
> [33]http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>      >   15. mailto:[34]pasik@xxxxxx
>      >   16.
>      [35]http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>      >   17.
>      
> [36]http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>      >   18. mailto:[37]pasik@xxxxxx
> 
> References
> 
>    Visible links
>    1. mailto:pasik@xxxxxx
>    2. mailto:pasik@xxxxxx
>    3. mailto:pasik@xxxxxx
>    4. mailto:pasik@xxxxxx
>    5. mailto:pasik@xxxxxx
>    6. mailto:pasik@xxxxxx
>    7. http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>    8. 
> http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>    9. mailto:pasik@xxxxxx
>   10. http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>   11. 
> http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>   12. mailto:pasik@xxxxxx
>   13. mailto:pasik@xxxxxx
>   14. http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>   15. 
> http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>   16. mailto:pasik@xxxxxx
>   17. http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>   18. 
> http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>   19. mailto:pasik@xxxxxx
>   20. mailto:pasik@xxxxxx
>   21. mailto:pasik@xxxxxx
>   22. mailto:pasik@xxxxxx
>   23. mailto:pasik@xxxxxx
>   24. mailto:pasik@xxxxxx
>   25. http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>   26. 
> http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>   27. mailto:pasik@xxxxxx
>   28. http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>   29. 
> http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>   30. mailto:pasik@xxxxxx
>   31. mailto:pasik@xxxxxx
>   32. http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>   33. 
> http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>   34. mailto:pasik@xxxxxx
>   35. http://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
>   36. 
> http://pasik.reaktio.net/xen/pv_ops-dom0-debug/config-2.6.32.9-pvops-dom0-xen-stable-x86_64
>   37. mailto:pasik@xxxxxx

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.