[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

AW: [Xen-devel] Still Time went backwards problems Xen 3.3.1/2.6.18.8



Leaving out cpuidle doesn't make any difference:

  Mar  7 22:45:04 data kernel: Timer ISR/0: Time went backwards: 
delta=-23283686 ...

I think unstable is going to got frozen soon. I guess this is next to 
try. 

BTW: again three seconds after munin-cron.

BR,
Carsten.
 
-----Ursprüngliche Nachricht-----
Von: Carsten Schiers 
Gesendet: Samstag, 7. März 2009 10:42
An: xen-devel
Cc: mark.langsdorf; keir.fraser
Betreff: [Xen-devel] Still Time went backwards problems Xen 
3.3.1/2.6.18.8

Still have problems with "Time went backwards" messages. Now I am nearly 
completely at Xen 3.3.1 and Xen kernel 2.6.18.8 for Dom0 and nearly all 
DomUs. There is only one DomU That is on a customized special kernel for 
Endian (2.6.21.7-2).

Q1: Can a DomU kernel version anyhow be responsible for that effect?

Attached you can see the last two days. I noticed that they occur every 
five minutes, so it's probably connected with the munin cron job that 
collects xen domain usage and cpufreq-stats. Nothing more. Delta is 
still quite huge, around 40 ms. 
Value is negative.

Q2: Is that any better than if it's positive?
Q3: Will the delta be reset or will it go up and down all the time?

Currently I use both cpufreq=dom0 and cpuidle. 

Q4: Can the problem eventually be related to either of them only?

Right now, I disabled cpuidle for the time being, to see whether there 
is a difference.
If not, I intend to use xen-unstable next. I attached the current xm 
dmesg and xm info, so don't be surprised to miss cpuidle.

Well, I am not sure whether I do too much work on this issue, but I 
think the log message is there for a reason. 

Best Regards,
Carsten.

P.S.: There are combinations that are much worse that this. Especially 
running Xen 3.3.1 and actual Lenny kernel seems to be worse.

-----Ursprüngliche Nachricht-----
Von: Langsdorf, Mark [mailto:mark.langsdorf@xxxxxxx]
Gesendet: Donnerstag, 15. Januar 2009 20:27
An: Carsten Schiers
Betreff: RE: RE: RE: RE: [Xen-devel] AMD P-States not recognized for Xen
3.3 and 3.4

If you have a single socket system, then fixing the out of sync issue 
will probably not fix the TSC issue.

If you have a dual or quad socket system, fixing the out of sync error 
should reduce the frequency and magnitude of the TSC issues.  At least, 
that's the best I can decipher from my notes.

Also, most of the work I did on cpufreq was in 2007, before Dan M. 
greatly redid Xen hypervisor time-keeping.
If an up-to-date kernel/hypervisor still has TSC problems, it may be 
possible to fix them.  I don't really have time to research it myself, 
but if you do have problems, please contact me and I'll see what can be 
done.

-Mark Langsdorf
Operating System Research Center
AMD

> -----Original Message-----
> From: Carsten Schiers [mailto:carsten@xxxxxxxxxx]
> Sent: Thursday, January 15, 2009 1:17 PM
> To: Langsdorf, Mark
> Subject: AW: RE: RE: RE: [Xen-devel] AMD P-States not recognized for 
> Xen 3.3 and 3.4
> 
> Thanks Mark, don't want to get on your nerve, but this will only fix 
> the
> powernow-k8 out of synch issue but not the fact that my 4050e will 
> have TSC issues between the two cores when switching frequencies, 
> right?
> 
> Am I right that there is no cure for that currently? And that I am not 

> safe to ignore them, because some kernel wizard is synchronizing them? 

> 'Cause up to now I only found a synch in boot.c.
> 
> Sorry for all those questions, it's quite complicated. My best times 
> as code producer habe been some 15 years ago...
> 
> Thanks,
> Carsten.
> 
> -----Ursprüngliche Nachricht-----
> Von: Langsdorf, Mark [mailto:mark.langsdorf@xxxxxxx]
> Gesendet: Donnerstag, 15. Januar 2009 18:23
> An: Carsten Schiers
> Betreff: RE: RE: RE: [Xen-devel] AMD P-States not recognized for Xen 
> 3.3 and 3.4
> 
> > Thank you Mark. Please excuse my small knowledge in kernel/xen 
> > hacking.  I understood that I should either
> > 
> >   a) create a build of the actual xen-unstable.hg together with 
> > linux-2.6.18-xen.hg kernel (where you think to have fixed
> the problem)
> >
> > or
> > 
> >   b) to include the mentioned fixes into my environment
> (which is the
> > 3.2.1 Xen and Bastian Blank's (waldi) kernel (based on 2.6.18, too), 

> > right?
> > 
> > I'll try out what will be more easy, but I think it should be a).
> 
> Right.  Using the latest unstable kernel & hypervisor gives you all 
> the patches.  If you're backporting support into the waldi kernel, you 

> need to make sure you backport all the relevant patches.
> 
> -Mark Langsdorf
> Operating System Research Center
> AMD
> 
> 
> 
> 
> 






_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.