Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip

[Andrew Lyon <andrew.lyon@xxxxxxxxx>]

On Sun, Feb 22, 2009 at 3:10 PM, Boris Derzhavets <bderzhavets@xxxxxxxxx> wrote:
>> I've also tried Xen 3.4 with the fix applied
>> for "pci device without power management"
> Is it possible to share "How to apply this patch" ?

Because the ioemu-remote sources do not exist until the build process
downloads them I had to use a very crude method, I started the Xen
build process and paused it every few seconds using ctrl+z, if
tools/ioemu-remote/hw/pass-through.c exists I applied the patch, if
not I resumed the process using "fg <enter>", after a while its easy
to spot when the code is downloaded.

The patch was posed to the mailing list with subject "[Xen-devel]
[PATCH] ioemu: Fix the segmentation fault on assigning device without
PM cap.", I copied the patch content into a text file and applied with
patch -p1 -i <patchfile>

But even with the patch applied qemu-dm crashes and the VM does not start.

Andy

>
> Boris.
>
>
> --- On Sun, 2/22/09, Andrew Lyon <andrew.lyon@xxxxxxxxx> wrote:
>
> From: Andrew Lyon <andrew.lyon@xxxxxxxxx>
> Subject: Re: [Xen-devel] Build vmlinuz-2.6.29-rc5-tip
> To: Ian.Jackson@xxxxxxxxxxxxx, "xen-devel@xxxxxxxxxxxxxxxxxxx"
> <xen-devel@xxxxxxxxxxxxxxxxxxx>
> Cc: "Jeremy Fitzhardinge" <jeremy@xxxxxxxx>
> Date: Sunday, February 22, 2009, 9:20 AM
>
> On Sat, Feb 21, 2009 at 3:53 PM, Jeremy Fitzhardinge <jeremy@xxxxxxxx>
> wrote:
>> Andrew Lyon wrote:
>>>
>>> I've also tried using 3.3.1 with the
>  backported patches as above,
> I
>>> still get a device model failure error but this time there is no
>>> mention of power management:
>>>
>>> [2009-02-21 12:32:33 3486] WARNING (image:472) domain xptest: device
>>> model failure: pid 3766: malfunctioning (closed sentinel), killed; see
>>> /var/log/xen/qemu-dm-xptest.log
>>>
>>
>> IanJ would have more of an idea about this stuff than me.
>
> I've now tried Xen 3.3.1 and 3.3.2 both with the backported patches
> from xen-unstable for pv_ops dom0 support, and I've also tried Xen 3.4
> with the fix applied for "pci device without power management", with
> all 3 a existing VM which works under a non pv_ops Xen kernel fails to
> start under pv_ops kernel, I've also tried different disk backends
> (tap:io, file:/) the error is always the same:
>
> [2009-02-22 14:07:25 3467] WARNING (image:470) domain xptest: device
> model failure:
>  pid 4224: malfunctioning (closed sentinel), killed; see
> /var/log/xen/qemu-dm-xptest.log
>
>
> cat /var/log/xen/qemu-dm-xptest.log
> domid: 4
> qemu: the number of cpus is 1
> Using xvda for guest's hda
> Strip off blktap sub-type prefix to /root/xp (drv 'aio')
> Watching /local/domain/0/device-model/4/logdirty/next-active
> Watching /local/domain/0/device-model/4/command
> qemu_map_cache_init nr_buckets = 10000 size 3145728
> shared page at pfn 1fffe
> buffered io page at pfn 1fffc
> Time offset set 0
> Register xen platform.
> Done register platform.
> I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0
>
> Andy
>
>
>>
>>   J
>>
>>>
>>>  cat /var/log/xen/qemu-dm-xptest.log
>>>
>>> domid: 1
>>> qemu: the number of cpus is 2
>>> Watching /local/domain/0/device-model/1/logdirty/next-active
>>> Watching
>  /local/domain/0/device-model/1/command
>>> qemu_map_cache_init nr_buckets = 10000 size 3145728
>>> shared page at pfn 1fffe
>>> buffered io page at pfn 1fffc
>>> Time offset set 0
>>> Register xen platform.
>>> Done register platform.
>>> medium change watch on `hdc' (index: 1):
>>> I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0
>>> I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0
>>>
>>> Which logfiles do I need to post to investigate this problem?
>>>
>>> Andy
>>>
>>
>>
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-devel
>
>

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel