|
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] Re: [Filtered!] [Xen-devel] Networking problems with xen3
On Sun, Nov 06, 2005 at 10:57:25PM -0000, Ian Pratt wrote: > > Ok, adding either noapic or acpi=noirq, both of which appear > > to result in the ioapic being ignored, results in everything > > working fine. So i guess there's been drift between 2.6.12 > > native and the xen3/2.6.12-xen combo in this area. > > OK, that's actually quite interesting. > > Please could you post a diff of the log meesages from a native boot > (with a similar config) vs on xen. Also, having the xen boot messages > woul be goo too. After figuring out that I was losing the start of my boot messages and rebuilding with a bigger dmesg buffer i got the following, all booted with lapic and apic=debug: native-vs-xen-fail.diff - 2.6.12.6 native against 2.6.12.6 xen xen-fail-vs-xen-work.diff - 2.6.12.6 xen against 2.6.12.6 xen with acpi=noirq dmesg.working-linux.gz - dmesg of 2.6.12.6 native dmesg.not-working-xen.gz - dmesg of xen3 dmesg.not-working-linux.gz - dmesg of 2.6.12.6 xen dmesg.working-noirq-xen.gz - dmesg of xen3 with acpi=noirq dmesg.working-noirq-linux.gz - dmesg of 2.6.12.6 xen with acpi=noirq J -- Jody Belka knew (at) pimb (dot) org --- dmesg.working-linux 2005-11-06 23:57:31.000000000 +0000 +++ dmesg.not-working-linux 2005-11-06 23:57:07.000000000 +0000 @@ -1,21 +1,10 @@ -Linux version 2.6.12 (jmb@artemis) (gcc version 3.3.5 (Debian 1:3.3.5-8ubuntu2)) #3 Sun Nov 6 23:33:16 GMT 2005 +Linux version 2.6.12.6-xen.priv-evms (jmb@artemis) (gcc version 3.3.5 (Debian 1:3.3.5-8ubuntu2)) #2 Sun Nov 6 23:38:46 GMT 2005 BIOS-provided physical RAM map: - BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) - BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) - BIOS-e820: 00000000000c8000 - 00000000000ce000 (reserved) - BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) - BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) - BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data) - BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS) - BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) - BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) - BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) -Warning only 896MB will be used. -Use a HIGHMEM enabled kernel. -896MB LOWMEM available. -On node 0 totalpages: 229376 - DMA zone: 4096 pages, LIFO batch:1 - Normal zone: 225280 pages, LIFO batch:31 + Xen: 0000000000000000 - 0000000010000000 (usable) +256MB LOWMEM available. +On node 0 totalpages: 65536 + DMA zone: 65536 pages, LIFO batch:31 + Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 AMI ) @ 0x000fa910 @@ -23,70 +12,41 @@ ACPI: FADT (v001 AMIINT VIA_K7 0x00000011 MSFT 0x00000097) @ 0x3fff0030 ACPI: MADT (v001 AMIINT VIA_K7 0x00000009 MSFT 0x00000097) @ 0x3fff00c0 ACPI: DSDT (v001 VIA K7VT4 0x00001000 MSFT 0x0100000d) @ 0x00000000 -ACPI: PM-Timer IO Port: 0x808 -ACPI: Local APIC address 0xfee00000 -ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) -Processor #0 6:8 APIC version 16 -ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) -IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23 -ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) -ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) -ACPI: IRQ0 used by override. -ACPI: IRQ2 used by override. -ACPI: IRQ9 used by override. -Enabling APIC mode: Flat. Using 1 I/O APICs -Using ACPI (MADT) for SMP configuration information +IRQ lockup detection disabled Allocating PCI resources starting at 40000000 (gap: 40000000:bec00000) Built 1 zonelists Kernel command line: root=/dev/evms/dom0-new/root ramdisk=16384 mem=49152 apic=debug lapic -mapped APIC to ffffd000 (fee00000) -mapped IOAPIC to ffffc000 (fec00000) Initializing CPU#0 -CPU 0 irqstacks, hard=c04c0000 soft=c04bf000 -PID hash table entries: 4096 (order: 12, 65536 bytes) -Detected 1499.861 MHz processor. -Using pmtmr for high-res timesource +CPU 0 irqstacks, hard=c04f0000 soft=c04ef000 +PID hash table entries: 2048 (order: 11, 32768 bytes) +Xen reported: 1673.756 MHz processor. Console: colour VGA+ 80x25 -Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) -Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) -Memory: 899296k/917504k available (2122k kernel code, 17620k reserved, 1518k data, 168k init, 0k highmem) +Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) +Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) +Software IO TLB disabled +vmalloc area: d0800000-fbeef000, maxmem 34000000 +Memory: 238080k/262144k available (2239k kernel code, 23852k reserved, 1614k data, 144k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. -Calibrating delay loop... 2965.50 BogoMIPS (lpj=1482752) +Calibrating delay loop... 3342.33 BogoMIPS (lpj=16711680) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) -CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000020 00000000 00000000 00000000 +CPU: After all inits, caps: 0383d3f1 c1cbfbff 00000000 00000020 00000000 00000000 00000000 CPU: AMD Sempron(tm) 2200+ stepping 01 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. -Checking 'hlt' instruction... OK. -Getting VERSION: 40010 -Getting VERSION: 40010 -Getting ID: 0 -Getting LVT0: 700 -Getting LVT1: 400 -enabled ExtINT on CPU#0 -ESR value before enabling vector: 0x00000080 after: 0x00000000 -ENABLING IO-APIC IRQs -Synchronizing Arb IDs. -init IO_APIC IRQs - IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected. -..TIMER: vector=0x31 pin1=2 pin2=-1 -Using local APIC timer interrupts. -calibrating APIC timer ... -..... CPU clock speed is 1499.0324 MHz. -..... host bus clock speed is 333.0183 MHz. -checking if image is initramfs...it isn't (no cpio magic); looks like an initrd -Freeing initrd memory: 5371k freed +Checking 'hlt' instruction... disabled +ACPI: setting ELCR to 0200 (from 0c28) +checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd +Freeing initrd memory: 16384k freed NET: Registered protocol family 16 -PCI: PCI BIOS revision 2.10 entry at 0xfdae1, last bus=1 +xenbus_probe_init PCI: Using configuration type 1 -mtrr: v2.0 (20020519) ACPI: Subsystem revision 20050309 ACPI: Interpreter enabled -ACPI: Using IOAPIC for interrupt routing +ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Boot video device is 0000:00:0d.0 @@ -101,69 +61,11 @@ ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init -IOAPIC[0]: Set PCI routing entry (2-4 -> 0x49 -> IRQ 4 Mode:0 Active:0) -IOAPIC[0]: Set PCI routing entry (2-7 -> 0x61 -> IRQ 7 Mode:0 Active:0) -IOAPIC[0]: Set PCI routing entry (2-8 -> 0x69 -> IRQ 8 Mode:0 Active:0) -IOAPIC[0]: Set PCI routing entry (2-13 -> 0x91 -> IRQ 13 Mode:0 Active:0) -IOAPIC[0]: Set PCI routing entry (2-1 -> 0x39 -> IRQ 1 Mode:0 Active:0) pnp: PnP ACPI: found 9 devices +xen_mem: Initialising balloon driver. PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report -number of MP IRQ sources: 15. -number of IO-APIC #2 registers: 24. -testing the IO APIC....................... -IO APIC #2...... -.... register #00: 02000000 -....... : physical APIC id: 02 -....... : Delivery Type: 0 -....... : LTS : 0 -.... register #01: 00178003 -....... : max redirection entries: 0017 -....... : PRQ implemented: 1 -....... : IO APIC version: 0003 -.... IRQ redirection table: - NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: - 00 000 00 1 0 0 0 0 0 0 00 - 01 001 01 1 0 0 0 0 1 1 39 - 02 001 01 0 0 0 0 0 1 1 31 - 03 001 01 0 0 0 0 0 1 1 41 - 04 001 01 1 0 0 0 0 1 1 49 - 05 001 01 0 0 0 0 0 1 1 51 - 06 001 01 0 0 0 0 0 1 1 59 - 07 001 01 1 0 0 0 0 1 1 61 - 08 001 01 1 0 0 0 0 1 1 69 - 09 001 01 0 1 0 1 0 1 1 71 - 0a 001 01 0 0 0 0 0 1 1 79 - 0b 001 01 0 0 0 0 0 1 1 81 - 0c 001 01 0 0 0 0 0 1 1 89 - 0d 001 01 1 0 0 0 0 1 1 91 - 0e 001 01 0 0 0 0 0 1 1 99 - 0f 001 01 0 0 0 0 0 1 1 A1 - 10 000 00 1 0 0 0 0 0 0 00 - 11 000 00 1 0 0 0 0 0 0 00 - 12 04E 0E 1 0 0 0 0 0 2 21 - 13 0B4 04 1 0 0 0 0 0 2 A2 - 14 000 00 1 0 0 0 0 0 0 00 - 15 000 00 1 0 0 0 0 0 0 00 - 16 000 00 1 0 0 0 0 0 0 00 - 17 000 00 1 0 0 0 0 0 0 00 -IRQ to pin mappings: -IRQ0 -> 0:2 -IRQ1 -> 0:1 -IRQ3 -> 0:3 -IRQ4 -> 0:4 -IRQ5 -> 0:5 -IRQ6 -> 0:6 -IRQ7 -> 0:7 -IRQ8 -> 0:8 -IRQ9 -> 0:9 -IRQ10 -> 0:10 -IRQ11 -> 0:11 -IRQ12 -> 0:12 -IRQ13 -> 0:13 -IRQ14 -> 0:14 -IRQ15 -> 0:15 -.................................... done. +Grant table initialized NTFS driver 2.1.22 [Flags: R/O]. Initializing Cryptographic API ACPI: Power Button (FF) [PWRF] @@ -174,8 +76,6 @@ serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled -ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A -ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] io scheduler noop registered @@ -187,13 +87,15 @@ Ethernet Channel Bonding Driver: v2.6.1 (October 29, 2004) bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details. via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker -IOAPIC[0]: Set PCI routing entry (2-23 -> 0xa9 -> IRQ 23 Mode:1 Active:1) -ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 23 -PCI: Via IRQ fixup for 0000:00:12.0, from 3 to 7 -eth0: VIA Rhine II at 0xdffdfe00, 00:0b:6a:a9:aa:4d, IRQ 23. +ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 3 +PCI: setting IRQ 3 as level-triggered +ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 3 (level, low) -> IRQ 3 +eth0: VIA Rhine II at 0xdffdfe00, 00:0b:6a:a9:aa:4d, IRQ 3. eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1. tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx> +WARNING: Failed to register Xen virtual console driver as 'ttyS0' +Event-channel device installed. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:11.1 @@ -227,21 +129,22 @@ Uniform CD-ROM driver Revision: 3.20 device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@xxxxxxxxxx NET: Registered protocol family 2 -IP: routing cache hash table of 8192 buckets, 64Kbytes -TCP established hash table entries: 131072 (order: 8, 1048576 bytes) -TCP bind hash table entries: 65536 (order: 6, 262144 bytes) -TCP: Hash tables configured (established 131072 bind 65536) -ip_conntrack version 2.1 (7168 buckets, 57344 max) - 172 bytes per conntrack -ip_tables: (C) 2000-2002 Netfilter core team input: AT Translated Set 2 keyboard on isa0060/serio0 +IP: routing cache hash table of 2048 buckets, 16Kbytes +TCP established hash table entries: 16384 (order: 5, 131072 bytes) +TCP bind hash table entries: 16384 (order: 4, 65536 bytes) +TCP: Hash tables configured (established 16384 bind 16384) +ip_conntrack version 2.1 (2048 buckets, 16384 max) - 172 bytes per conntrack +ip_tables: (C) 2000-2002 Netfilter core team NET: Registered protocol family 1 NET: Registered protocol family 17 -RAMDISK: Compressed image found at block 0 +RAMDISK: ext2 filesystem found at block 0 +RAMDISK: Loading 16384KiB [1 disk] into ram disk... done. EXT2-fs warning: checktime reached, running e2fsck is recommended VFS: Mounted root (ext2 filesystem). kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. -Freeing unused kernel memory: 168k freed +Freeing unused kernel memory: 144k freed EXT3 FS on dm-6, internal journal Adding 131060k swap on /dev/evms/dom0-new/swap/0. Priority:-1 extents:1 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 --- dmesg.not-working-linux 2005-11-06 23:57:07.000000000 +0000 +++ dmesg.working-noirq-linux 2005-11-07 00:03:04.000000000 +0000 @@ -15,11 +15,11 @@ IRQ lockup detection disabled Allocating PCI resources starting at 40000000 (gap: 40000000:bec00000) Built 1 zonelists -Kernel command line: root=/dev/evms/dom0-new/root ramdisk=16384 mem=49152 apic=debug lapic +Kernel command line: root=/dev/evms/dom0-new/root ramdisk=16384 mem=49152 apic=debug lapic acpi=noirq Initializing CPU#0 CPU 0 irqstacks, hard=c04f0000 soft=c04ef000 PID hash table entries: 2048 (order: 11, 32768 bytes) -Xen reported: 1673.756 MHz processor. +Xen reported: 1673.761 MHz processor. Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) @@ -38,7 +38,7 @@ Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... disabled -ACPI: setting ELCR to 0200 (from 0c28) +ACPI: setting ELCR to 0e28 (from 0c28) checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd Freeing initrd memory: 16384k freed NET: Registered protocol family 16 @@ -55,16 +55,14 @@ ACPI: Power Resource [URP2] (off) ACPI: Power Resource [FDDP] (off) ACPI: Power Resource [LPTP] (off) -ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 7 10 11 12 14 15) -ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 *11 12 14 15) -ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 12 14 15) -ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 9 devices xen_mem: Initialising balloon driver. -PCI: Using ACPI for IRQ routing -PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report +PCI: Probing PCI hardware +PCI: Using IRQ router default [1106/3177] at 0000:00:11.0 +PCI: IRQ 0 for device 0000:00:11.1 doesn't match PIRQ mask - try pci=usepirqmask +PCI: Hardcoded IRQ 14 for device 0000:00:11.1 Grant table initialized NTFS driver 2.1.22 [Flags: R/O]. Initializing Cryptographic API @@ -87,9 +85,6 @@ Ethernet Channel Bonding Driver: v2.6.1 (October 29, 2004) bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details. via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker -ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 3 -PCI: setting IRQ 3 as level-triggered -ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 3 (level, low) -> IRQ 3 eth0: VIA Rhine II at 0xdffdfe00, 00:0b:6a:a9:aa:4d, IRQ 3. eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1. tun: Universal TUN/TAP device driver, 1.6 @@ -99,8 +94,8 @@ Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:11.1 -ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI -PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 15 +PCI: Hardcoded IRQ 14 for device 0000:00:11.1 +PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 14 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1 Attachment:
dmesg.working-linux.gz Attachment:
dmesg.not-working-xen.gz Attachment:
dmesg.not-working-linux.gz Attachment:
dmesg.working-noirq-xen.gz Attachment:
dmesg.working-noirq-linux.gz _______________________________________________ Xen-devel mailing list Xen-devel@xxxxxxxxxxxxxxxxxxx http://lists.xensource.com/xen-devel
|
 |
Lists.xenproject.org is hosted with RackSpace, monitoring our |