Yes that does sound suspicious. If you only have one nic I would remove the
bonding just in case that is adding to the problem.
I would stop xend from automatically starting on the next reboot.
-reboot,
- check that the network works. If it doesn't then in Yast or manually
configure the nic so it will.
if it does then
- issue the network-script (whatever the name is I don't remember off hand)
command manually and check the output. ( redirect to a file so you can post it
here)
- ifconfig > ifconfig.txt
- brctrl show > bridge.txt
- route -nee > route.txt
You many want to disable the firewall temporally as well.
-brent
>>> "Patrick Lefebvre" <thepcguy@xxxxxxxxxxxxxx> 12/15/2010 4:45 PM >>>
I followed that.
It doesn't seem to matter.
With or without bonding, it doesn't seem to make a difference.
I get a plain vanilla setup of one eth0 working in "normal" mode, and
nothing in Xen mode.
I did just find something in the messages log about No configuration
found for tmpbridge
Which may be indicative of a bug needing an update.
On Wed, 15 Dec 2010 16:21 -0500, "Brent Alcorn"
<Brent.Alcorn@xxxxxxxxxxxx> wrote:
> bond0? do you have more than one nic?
>
> I am using only one nic so I am not using bonding and therefore do not
> have bond0.
>
> I believe there are some articles on the Novell site on setting up
> bonding of nics in Xen.
>
>
>
>
> >>> "Patrick Lefebvre" 12/15/10 3:30 PM >>>
> Yes, ifconfig shows all the interfaces.
> bond0
> Eth0
> io
> peth0
>
> All up and running.
> If I manually assign an IP address to them, they also show up in
> ifconfig.
> brctl show says that eth0 is bridged to peth0
>
>
>
> On Wed, 15 Dec 2010 15:22 -0500, "Brent Alcorn"
> wrote:
> > It shouldn't but I vaguely remember some issue with that, but, I'm not
> > sure.
> >
> > Once booted in Xen can you verify that the bridge script worked and you
> > have an eth0 and a peth0? and "brctl show" cmd shows that it is bridged?
> >
> > I believe I had to delete the xen network interface and re-add it at one
> > point. But that was over a year ago so I don't recall exactly and I was
> > messing with opensuse at the time too.
> >
> >
> >
> >
> > >>> "Patrick Lefebvre" 12/15/10 2:54 PM >>>
> > Would that change when switching from booting into Xen to booting into
> > normal modes?
> >
> >
> > On Wed, 15 Dec 2010 14:45 -0500, "Brent Alcorn"
> > wrote:
> > > Is the default gateway set for eth0? I seem to remember that doesn't
> > > stick sometimes when entered via Yast.
> > >
> > >
> > > >>> "Patrick Lefebvre" 12/15/10 1:56 PM >>>
> > > I left the traditional interface. In fact I don't even have the network
> > > manager installed.
> > >
> > >
> > >
> > > On Wed, 15 Dec 2010 13:30 -0500, "Brent Alcorn"
> > > wrote:
> > > > Hi Patrick,
> > > >
> > > > Are you using the traditional network interface or the network manager?
> > > > In my experience It will make a difference; leave it as traditional.
> > > >
> > > > I set my system up using the "traditional" method and it works great.
> > > >
> > > > Regards,
> > > > Brent
> > > >
> > > >
> > > >
> > > > >>> "Patrick Lefebvre" 12/15/10 1:06 PM >>>
> > > > I am trying to set up Xen on SLES 10 SP3
> > > > I installed SLES without problems. Everything worked and I had normal
> > > > network access.
> > > >
> > > > After that, I installed Xen and tools from Yast2
> > > > Everything installed normally.
> > > >
> > > > However, when I restart the system with Xen, I lose all network
> > > > connectivity.
> > > > Everything in the logs show the interfaces as loading normally (logs,
> > > > Dmesg, ifconfig etc)
> > > > All the interfaces seem to come up, but DHCP gets no address and there
> > > > is no connectivity.
> > > > I can set a static IP, the interface loads normally, I can ping it's IP
> > > > address locally without error, but I cannot ping anything on the
> > > > network.
> > > > Which tells me the interface actually DOES come up... but it just cannot
> > > > connect for some reason.
> > > >
> > > > If I restart on the "normal" kernel without Xen... everything comes back
> > > > to normal with the network working properly.
> > > > I reboot under Xen... no network.
> > > >
> > > > I tried following instructions on how to set up a bounded interface.
> > > > Same thing... works on normal kernel, no access under Xen.
> > > >
> > > > What am I missing???
> > > > I'm getting pretty frustrated...
> > > > please help.
> > > > Thanks.
> > > > --
> > > > Patrick Lefebvre
> > > > thepcguy@xxxxxxxxxxxxxx
> > > >
> > > > --
> > > > http://www.fastmail.fm - Accessible with your email software
> > > > or over the web
> > > >
> > > >
> > > > _______________________________________________
> > > > Xen-users mailing list
> > > > Xen-users@xxxxxxxxxxxxxxxxxxx
> > > > http://lists.xensource.com/xen-users
> > > >
> > > --
> > > Patrick Lefebvre
> > > thepcguy@xxxxxxxxxxxxxx
> > >
> > > --
> > > http://www.fastmail.fm - Choose from over 50 domains or use your own
> > >
> > >
> > > _______________________________________________
> > > Xen-users mailing list
> > > Xen-users@xxxxxxxxxxxxxxxxxxx
> > > http://lists.xensource.com/xen-users
> > >
> > --
> > Patrick Lefebvre
> > thepcguy@xxxxxxxxxxxxxx
> >
> > --
> > http://www.fastmail.fm - Faster than the air-speed velocity of an
> > unladen european swallow
> >
> >
> --
> Patrick Lefebvre
> thepcguy@xxxxxxxxxxxxxx
>
> --
> http://www.fastmail.fm - Send your email first class
>
>
--
Patrick Lefebvre
thepcguy@xxxxxxxxxxxxxx
--
http://www.fastmail.fm - Email service worth paying for. Try it for free
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|