|
|
|
|
|
|
|
|
|
|
xen-users
Re: [Xen-devel] Re: [Xen-users] dom0 hangs in xen 4.0.1-rc3-pre
The following is the output of "xenpm start 10".
CPU0: Residency(ms) Avg Res(ms) C0 100 ( 1.01%) 0.02 C1 10 ( 0.10%) 0.12
C2 9892 (98.89%) 2.43 C3 0 ( 0.00%) 0.00
P0 0 ( 0.00%) P1 0 ( 0.00%) P2 0 ( 0.00%) P3 54 (100.00%)
Avg freq 1980000 KHz
CPU1: Residency(ms) Avg Res(ms) C0 136 ( 1.37%) 0.02 C1 11 ( 0.11%) 0.19 C2 9855 (98.52%) 1.62
C3 0 ( 0.00%) 0.00
P0 0 ( 0.00%) P1 0 ( 0.00%) P2 0 ( 0.00%) P3 72 (100.00%) Avg freq 1980000 KHz
CPU2: Residency(ms) Avg Res(ms) C0 153 ( 1.53%) 0.02 C1 58 ( 0.59%) 0.35 C2 9791 (97.88%) 1.43 C3 0 ( 0.00%) 0.00
P0 0 ( 0.00%) P1 0 ( 0.00%) P2 0 ( 0.00%) P3 85 (100.00%) Avg freq 1980000 KHz
CPU3: Residency(ms) Avg Res(ms)
C0 177 ( 1.77%) 0.02 C1 33 ( 0.34%) 0.09 C2 9792 (97.89%) 1.05 C3 0 ( 0.00%) 0.00
P0 0 ( 0.00%)
P1 0 ( 0.00%) P2 0 ( 0.00%) P3 82 (100.00%) Avg freq 1980000 KHz
CPU4: Residency(ms) Avg Res(ms) C0 166 ( 1.67%) 0.01
C1 947 ( 9.47%) 0.21 C2 8889 (88.86%) 0.72 C3 0 ( 0.00%) 0.00
P0 0 ( 0.00%) P1 0 ( 0.00%)
P2 0 ( 0.00%) P3 11 (100.00%) Avg freq 1980000 KHz
CPU5: Residency(ms) Avg Res(ms) C0 722 ( 7.23%) 0.04
C1 181 ( 1.81%) 0.09 C2 9098 (90.96%) 0.53 C3 0 ( 0.00%) 0.00
P0 0 ( 0.00%) P1 0 ( 0.00%)
P2 0 ( 0.00%) P3 529 (100.00%) Avg freq 1980000 KHz
CPU6: Residency(ms) Avg Res(ms) C0 73 ( 0.73%) 0.02
C1 5 ( 0.06%) 0.16 C2 9923 (99.21%) 2.44 C3 0 ( 0.00%) 0.00
P0 0 ( 0.00%) P1 0 ( 0.00%)
P2 0 ( 0.00%) P3 27 (100.00%) Avg freq 1980000 KHz
CPU7: Residency(ms) Avg Res(ms) C0 135 ( 1.35%) 0.02
C1 68 ( 0.68%) 0.27 C2 9799 (97.97%) 1.55 C3 0 ( 0.00%) 0.00
P0 0 ( 0.00%) P1 0 ( 0.00%)
P2 0 ( 0.00%) P3 71 (100.00%) Avg freq 1980000 KHz
Thanks On Mon, Sep 27, 2010 at 4:17 AM, Andreas Kinzler <ml-xen-devel@xxxxxx> wrote:
On 26.09.2010 03:12, Jia Rao wrote:
Please post your hardware (mainboard, chipset, CPU, RAID controller).
I have found a severe problem on Lynnfield systems.
Server Model: Dell PowerEdge 1950 III
Motherboard: do not actually know.
CPU: Intel Xeon E5450
Hard drive controller: No RAID. SAS 6/i R integrated controller.
OK. This is no Nehalem based system. Are you using C3 anyway? Please post output of "xenpm start 10".
Regards Andreas
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
|
|
|
|