On Fri, Apr 09, 2010 at 07:18:32AM +0200, For@ll wrote:
> W dniu 08.04.2010 22:43, Pasi Kärkkäinen pisze:
> > On Thu, Apr 08, 2010 at 09:46:49PM +0200, For@ll wrote:
> >
> >> > See here for help:
> >> [2][3]http://wiki.xensource.com/xenwiki/XenParavirtOps
> >> >
> >> > I have the same problem to boot xen 4.0 on debian lenny 5.0,
> >> under
> >> I
> >> > paste a some error:
> >> >
> >> > 41.017078] Magic number: 6:876:244
> >> > [ 41.061177] md: Waiting for all devices to be available before
> >> > autodetect
> >> > [ 41.142579] md: If you don't use raid, use raid=noautodetect
> >> > [ 41.211225] md: Autodetecting RAID arrays.
> >> > [ 41.260417] md: Scanned 0 and added 0 devices.
> >> > [ 41.313729] md: autorun ...
> >> > [ 41.347281] md: ... autorun DONE.
> >> > [ 41.387150] Root-NFS: No NFS server available, giving up.
> >> > [ 41.451921] VFS: Unable to mount root fs via NFS, trying
> >> floppy.
> >> > [ 41.524664] VFS: Cannot open root device "sda1" or
> >> unknown-block(2,0)
> >>
> >> So the disk was not detected, or did you pass wrong root= parameter?
> >>
> >> Please post the _full_ log.
> >>
> >> -- Pasi
> >>
> >>
> >> Hi,
> >>
> >> This is a longer version dmesg from console redirection ( ipmitool
> >> connect
> >> to iRMC)
> >>
> >>
> > I don't see any disks detected in the log..
> >
> > Can you please post a boot log on baremetal (non-xen),
> > or tell which disk controller has your root disk? what driver it uses on
> > baremetal linux?
> >
> > -- Pasi
> >
> >
>
> Hi,
>
> My disk controler:
>
> 00:1f.2 IDE interface: Intel Corporation 5 Series/3400 Series Chipset 4
> port SATA IDE Controller (rev 05)
> 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus
> Controller (rev 05)
> 00:1f.5 IDE interface: Intel Corporation 5 Series/3400 Series Chipset 2
> port SATA IDE Controller (rev 05)
> 05:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET
> PCI-Express Fusion-MPT SAS (rev 08)
>
> 15.990184] Fusion MPT SAS Host driver 3.04.06
> [ 16.043300] ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level,
> low) -> IRQ 16
> [ 16.131780] mptbase: ioc0: Initiating bringup
> [ 16.186195] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 21 (level,
> low) -> IRQ 21
> [ 16.271581] ehci_hcd 0000:00:1a.0: EHCI Host Controller
> [ 16.335331] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned
> bus number 1
> [ 16.428149] ehci_hcd 0000:00:1a.0: debug port 2
> [ 16.482831] ehci_hcd 0000:00:1a.0: irq 21, io mem 0xce003000
> [ 16.569265] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00, driver
> 10 Dec 2004
> [ 16.657988] usb usb1: configuration #1 chosen from 1 choice
> [ 16.758032] hub 1-0:1.0: USB hub found
> [ 16.802529] hub 1-0:1.0: 2 ports detected
> [ 16.953604] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
> [ 17.034700] usb usb1: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [ 17.293039] usb usb1: Product: EHCI Host Controller
> [ 17.432093] usb usb1: Manufacturer: Linux 2.6.26-2-686-bigmem ehci_hcd
> [ 17.510449] usb usb1: SerialNumber: 0000:00:1a.0
> [ 17.691888] usb 1-1: new high speed USB device using ehci_hcd and
> address 2
> [ 17.902387] usb 1-1: configuration #1 chosen from 1 choice
> [ 17.970725] hub 1-1:1.0: USB hub found
> [ 18.017157] hub 1-1:1.0: 6 ports detected
> [ 18.094031] ioc0: LSISAS1064E B3: Capabilities={Initiator}
> [ 18.094031] mptbase: ioc0: PCI-MSI enabled
> [ 18.171795] usb 1-1: New USB device found, idVendor=8087, idProduct=0020
> [ 18.171797] usb 1-1: New USB device strings: Mfr=0, Product=0,
> SerialNumber=0
> [ 27.514134] scsi0 : ioc0: LSISAS1064E B3, FwRev=011b0000h, Ports=1,
> MaxQ=277, IRQ=215
> [ 27.628920] scsi 0:0:0:0: Direct-Access ATA WDC WD2502ABYS-5
> 3B04 PQ: 0 ANSI: 5
> [ 27.744107] scsi 0:0:1:0: Direct-Access ATA WDC WD2502ABYS-5
> 3B04 PQ: 0 ANSI: 5
> [ 27.846823] scsi 0:1:0:0: Direct-Access LSILOGIC Logical Volume
> 3000 PQ: 0 ANSI: 2
> [ 27.943701] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level,
> low) -> IRQ 20
> [ 28.231483] ehci_hcd 0000:00:1d.0: EHCI Host Controller
> [ 28.295499] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned
> bus number 2
> [ 28.387771] ehci_hcd 0000:00:1d.0: debug port 2
> [ 28.441880] ehci_hcd 0000:00:1d.0: irq 20, io mem 0xce004000
> [ 28.513935] Driver 'sd' needs updating - please use bus_type methods
> [ 28.591370] sd 0:1:0:0: [sda] 486326272 512-byte hardware sectors
> (248999 MB)
> [ 28.668013] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00, driver
> 10 Dec 2004
> [ 28.668013] usb usb2: configuration #1 chosen from 1 choice
> [ 28.668013] hub 2-0:1.0: USB hub found
> [ 28.668013] hub 2-0:1.0: 2 ports detected
> [ 28.989376] sd 0:1:0:0: [sda] Write Protect is off
> [ 29.253072] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
> [ 29.253072] usb usb2: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [ 29.253072] usb usb2: Product: EHCI Host Controller
> [ 29.253072] usb usb2: Manufacturer: Linux 2.6.26-2-686-bigmem ehci_hcd
> [ 29.253072] usb usb2: SerialNumber: 0000:00:1d.0
> [ 29.471527] usb 2-1: new high speed USB device using ehci_hcd and
> address 2
> [ 29.727995] sd 0:1:0:0: [sda] Write cache: disabled, read cache:
> enabled, doesn't support DPO or FUA
> [ 29.868274] No dock devices found.
> [ 29.873610] sd 0:1:0:0: [sda] 486326272 512-byte hardware sectors
> (248999 MB)
> [ 29.873867] sd 0:1:0:0: [sda] Write Protect is off
> [ 29.874327] sd 0:1:0:0: [sda] Write cache: disabled, read cache:
> enabled, doesn't support DPO or FUA
> [ 29.874327] sda: sda1 sda2 sda3
> [ 30.204818] sd 0:1:0:0: [sda] Attached SCSI disk
>
>
> Debian Lenny with kernel 2.6.26-2-bigmem
>
Hmm.. and did you use the Lenny 2.6.26-2-xen kernel with Xen 4.0.0 ?
or pvops dom0 kernel? which version?
-- Pasi
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
Home