| |
|
 |
|
 |
|
|
|
| |
|
|
xen-users
Re: [Xen-users] SATA drives will not start under xen
Quoting Mike Lovell <mike@xxxxxxxxxxxx>:
Chris wrote:
Quoting Mike Lovell <mike@xxxxxxxxxxxx>:
On 7/18/2009 6:57 PM, Chris wrote:
Hello.
I am having a peculiar problem. I am running a dual amd64 system
on a Tyan Tomcat h1000s S3950 motherboard with 4 Gigs of ram
and two SATA 3.0 g/s seagate drives (in RAID 1 configuration
using LVM2). I am using Gentoo Linux, current as of today.
When I boot the system, everything looks good until it starts the
drives, then the system chokes and spits out a bunch of errors
like these:
--------------------
ACPI: PCI Interrupt 0000:01:0e.0[A] -> GSI 11 (level, low) -> IRQ 11
ata1: SATA max UDMA/133 cmd 0xffffc2000002c000 ctl
0xffffc2000002c020 bmdma 0xffffc2000002c031
ata2: SATA max UDMA/133 cmd 0xffffc2000002c100 ctl
0xffffc2000002c120 bmdma 0xffffc2000002c131
ata3: SATA max UDMA/133 cmd 0xffffc2000002c200 ctl
0xffffc2000002c220 bmdma 0xffffc2000002c231
ata4: SATA max UDMA/133 cmd 0xffffc2000002c300 ctl
0xffffc2000002c320 bmdma 0xffffc2000002c331
scsi0: sata_svw
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: ST3250410AS, 3.AAC, max UDMA/133
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: qc timeout (cmd0xef)
ata1.00: failed to set xfermode (err_mask=0x4)
ata1: failed to recover some devices retrying in 5 secs
(starts over with SATA link up 1.5 gbps...)
------------------------------------------
Eventually the system gives up (after struggling for like 10
minutes) and locks up hard.
I found that if I disabled APIC in the BIOS, it will boot -- but
as soon as I try to start the network, the logs fill with more
of the same junk, and the system locks up hard.
I installed a regular gentoo kernel, and used the exact same
config file -- the system boots just fine. No problems
what-so-ever. So, this is definitely a Xen thing...
Anything I can do to fix this?
btw: using kernel version 2.6.21-xen -- the most recent kernel in
portage -- and xen 3.4.0
Do you get these same errors on an non-xenified kernel? Also, do the
errors always contains errors complaining about ata1 or scsi0? If this
is the case, then the first disk on the controller is bad and probably
should be replaced. These errors are usually the driver detecting a
problem disk and trying to handle the errors. Hope that answers your
question.
mike
As I stated, I have installed a regular gentoo kernel with the same
exact .config file, and I do NOT have these problems. Only with
Xen. The controller is fine... Gotta be a Xen issue. It stinks
of an IRQ or some similar conflict to me...
Any other ideas?
Thanks.
My bad for not completely reading your email. Sry.
Was the regular kernel you used also a 2.6.21 kernel? I am assuming so
since you said you used the exact same .config file and that is always
changing between kernel versions. I have never used a controller that
uses the sata_svw driver. One other option would be to use a newer
kernel. There may not be a newer version in portage, but there are
people that have made newer working tarballs.
http://lists.xensource.com/archives/html/xen-users/2009-06/msg00200.html
http://code.google.com/p/gentoo-xen-kernel/
Hunting around the mailing list archives should turn up some additional
resources. Hopefully these sites or the archives can help you out.
mike
Boy, I hate straying from portage when I don't have to... makes
upgrading such a pain... but... if that is what it takes, I'll give it
a shot.
(btw, I did use a newer kernel, cuz there is no 2.6.21 in portage
right now, and like I said, I try to stay with the package manager
where possible.)
Thanks for the input here, Mike. I'll give your suggestion a try.
I'll post back with results..
-Chris
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
|
|
| |
|
Home