Bootdata ok (command line is root=/dev/mapper/RootVG-root ro) Linux version 2.6.18.8-xen (root@susi) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Tue Oct 28 18:27:23 CET 2008 BIOS-provided physical RAM map: Xen: 0000000000000000 - 0000000040800000 (usable) DMI 2.4 present. On node 0 totalpages: 260580 DMA zone: 4040 pages, LIFO batch:0 DMA32 zone: 256540 pages, LIFO batch:31 No mptable found. ACPI: RSDP (v002 INTEL ) @ 0x00000000000f03c0 ACPI: XSDT (v001 INTEL DQ45CB 0x0000003d MSFT 0x00010013) @ 0x00000000bfd4ee18 ACPI: FADT (v004 INTEL A M I 0x06222004 MSFT 0x00010013) @ 0x00000000bfd4dd98 ACPI: MADT (v002 INTEL DQ45CB 0x0000003d MSFT 0x00010013) @ 0x00000000bfd4df18 ACPI: MCFG (v001 INTEL DQ45CB 0x0000003d MSFT 0x00000097) @ 0x00000000bfd58e18 ACPI: ASF! (v032 INTEL DQ45CB 0x0000003d TFSM 0x000f4240) @ 0x00000000bfd57d18 ACPI: SPCR (v001 INTEL DQ45CB 0x0000003d AMI. 0x00000003) @ 0x00000000bfd58d18 ACPI: TCPA (v002 INTEL DQ45CB 0x0000003d MSFT 0x01000013) @ 0x00000000bfd58c98 ACPI: (v001 INTEL DQ45CB 0x0000003d INTL 0x00000001) @ 0x00000000bfd42f18 >>> ERROR: Invalid checksum ACPI: DSDT (v001 INTEL DQ45CB 0x0000003d INTL 0x20051117) @ 0x0000000000000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to xen Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at c0000000 (gap: bff00000:3ee1c000) Built 1 zonelists. Total pages: 260580 Kernel command line: root=/dev/mapper/RootVG-root ro Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Xen reported: 2833.018 MHz processor. Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Software IO TLB enabled: Aperture: 64 megabytes Kernel range: ffff880002951000 - ffff880006951000 Address size: 27 bits PCI-DMA: Using software bounce buffering for IO (SWIOTLB) Memory: 942260k/1056768k available (2040k kernel code, 106148k reserved, 887k data, 176k init) Calibrating delay using timer specific routine.. 5667.82 BogoMIPS (lpj=28339103) Security Framework v1.0.0 initialized Capability LSM initialized Mount-cache hash table entries: 256 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 6144K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 SMP alternatives: switching to UP code ACPI: Core revision 20060707 SMP alternatives: switching to SMP code Initializing CPU#1 Initializing CPU#2 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 6144K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 Brought up 4 CPUs Initializing CPU#3 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 6144K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 3 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 6144K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 2 migration_cost=19 checking if image is initramfs... it is Freeing initrd memory: 15638k freed PM: Adding info for No Bus:platform NET: Registered protocol family 16 PM: Adding info for No Bus:xen PM: Adding info for No Bus:xen-backend ACPI: bus type pci registered PCI: Using configuration type 1 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing PM: Adding info for acpi:acpi ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PM: Adding info for No Bus:pci0000:00 Boot video device is 0000:01:00.0 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] PM: Adding info for pci:0000:00:00.0 PM: Adding info for pci:0000:00:01.0 PM: Adding info for pci:0000:00:03.0 PM: Adding info for pci:0000:00:03.2 PM: Adding info for pci:0000:00:03.3 PM: Adding info for pci:0000:00:19.0 PM: Adding info for pci:0000:00:1a.0 PM: Adding info for pci:0000:00:1a.1 PM: Adding info for pci:0000:00:1a.2 PM: Adding info for pci:0000:00:1a.7 PM: Adding info for pci:0000:00:1b.0 PM: Adding info for pci:0000:00:1c.0 PM: Adding info for pci:0000:00:1c.3 PM: Adding info for pci:0000:00:1d.0 PM: Adding info for pci:0000:00:1d.1 PM: Adding info for pci:0000:00:1d.2 PM: Adding info for pci:0000:00:1d.7 PM: Adding info for pci:0000:00:1e.0 PM: Adding info for pci:0000:00:1f.0 PM: Adding info for pci:0000:00:1f.2 PM: Adding info for pci:0000:00:1f.3 PM: Adding info for pci:0000:01:00.0 PM: Adding info for pci:0000:01:00.1 PM: Adding info for pci:0000:03:00.0 PM: Adding info for pci:0000:04:00.0 PM: Adding info for pci:0000:04:01.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 *7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init PM: Adding info for No Bus:pnp0 pnp: ACPI device : hid PNP0A08 PM: Adding info for pnp:00:00 pnp: ACPI device : hid PNP0C01 PM: Adding info for pnp:00:01 pnp: ACPI device : hid PNP0C02 PM: Adding info for pnp:00:02 pnp: ACPI device : hid PNP0501 PM: Adding info for pnp:00:03 pnp: ACPI device : hid PNP0200 PM: Adding info for pnp:00:04 pnp: ACPI device : hid PNP0B00 PM: Adding info for pnp:00:05 pnp: ACPI device : hid PNP0800 PM: Adding info for pnp:00:06 pnp: ACPI device : hid PNP0C02 PM: Adding info for pnp:00:07 pnp: ACPI device : hid PNP0C04 PM: Adding info for pnp:00:08 pnp: ACPI device : hid PNP0C01 PM: Adding info for pnp:00:09 pnp: PnP ACPI: found 10 devices xen_mem: Initialising balloon driver. PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: the driver 'system' has been registered pnp: match found with the PnP device '00:01' and the driver 'system' pnp: match found with the PnP device '00:02' and the driver 'system' pnp: 00:02: ioport range 0xa20-0xa3f has been reserved pnp: 00:02: ioport range 0xa00-0xa1f has been reserved pnp: 00:02: ioport range 0xb78-0xb7f has been reserved pnp: 00:02: ioport range 0xf78-0xf7f has been reserved pnp: match found with the PnP device '00:07' and the driver 'system' pnp: match found with the PnP device '00:09' and the driver 'system' pnp: 00:09: ioport range 0x400-0x47f could not be reserved pnp: 00:09: ioport range 0x1180-0x119f has been reserved pnp: 00:09: ioport range 0x500-0x57f has been reserved PCI: Bridge: 0000:00:01.0 IO window: b000-bfff MEM window: c0000000-d00fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.3 IO window: a000-afff MEM window: d0200000-d02fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: 9000-9fff MEM window: d0100000-d01fffff PREFETCH window: d0400000-d04fffff GSI 16 sharing vector 0xB0 and IRQ 16 ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:01.0 to 64 GSI 17 sharing vector 0xB8 and IRQ 17 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.0 to 64 GSI 18 sharing vector 0xC0 and IRQ 18 ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1c.3 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 6, 262144 bytes) TCP established hash table entries: 131072 (order: 9, 2097152 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered PM: Adding info for platform:pcspkr IA-32 Microcode Update Driver: v1.14a-xen audit: initializing netlink socket (disabled) audit(1226581303.789:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) 0000:00:1a.7 EHCI: BIOS handoff failed (BIOS bug ?) 01010001 0000:00:1d.7 EHCI: BIOS handoff failed (BIOS bug ?) 01010001 PM: Adding info for platform:vesafb.0 Real Time Clock Driver v1.12ac Non-volatile memory driver v1.2 RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize loop: loaded (max 8 devices) Xen virtual console successfully installed as xvc0 Event-channel device installed. netfront: Initialising virtual ethernet driver. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx pnp: the driver 'ide' has been registered pnp: the driver 'i8042 kbd' has been registered pnp: the driver 'i8042 aux' has been registered pnp: the driver 'i8042 kbd' has been unregistered pnp: the driver 'i8042 aux' has been unregistered PNP: No PS/2 controller found. Probing ports directly. PM: Adding info for platform:i8042 serio: i8042 AUX port at 0x60,0x64 irq 12 PM: Adding info for serio:serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 PM: Adding info for serio:serio1 mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 NET: Registered protocol family 1 NET: Registered protocol family 17 ACPI: (supports S0 S1 S3 S4 S5) BIOS EDD facility v0.16 2004-Jun-25, 2 devices found Freeing unused kernel memory: 176k freed md: raid1 personality registered for level 1 SCSI subsystem initialized ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ AMI] OemTableId [ IST] [20060707] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) ACPI: CPU2 (power states: C1[C1] C2[C2] C3[C3]) ACPI: CPU3 (power states: C1[C1] C2[C2] C3[C3]) ACPI Exception (acpi_processor-0712): AE_NOT_FOUND, Processor Device is not present [20060707] ACPI: Getting cpuindex for acpiid 0x5 ACPI Exception (acpi_processor-0712): AE_NOT_FOUND, Processor Device is not present [20060707] ACPI: Getting cpuindex for acpiid 0x6 ACPI Exception (acpi_processor-0712): AE_NOT_FOUND, Processor Device is not present [20060707] ACPI: Getting cpuindex for acpiid 0x7 ACPI Exception (acpi_processor-0712): AE_NOT_FOUND, Processor Device is not present [20060707] ACPI: Getting cpuindex for acpiid 0x8 usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1a.0 to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000c0e0 PM: Adding info for usb:usb1 PM: Adding info for No Bus:usbdev1.1_ep00 usb usb1: configuration #1 chosen from 1 choice PM: Adding info for usb:1-0:1.0 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected libata version 2.00 loaded. Intel(R) PRO/1000 Network Driver - version 7.1.9-k4-NAPI Copyright (c) 1999-2006 Intel Corporation. ieee1394: Initialized config rom entry `ip1394' PM: Adding info for No Bus:usbdev1.1_ep81 GSI 19 sharing vector 0xC8 and IRQ 19 ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1a.1 to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1a.1: irq 19, io base 0x0000c0c0 PM: Adding info for usb:usb2 PM: Adding info for No Bus:usbdev2.1_ep00 usb usb2: configuration #1 chosen from 1 choice PM: Adding info for usb:2-0:1.0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev2.1_ep81 GSI 20 sharing vector 0xD0 and IRQ 20 ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 18 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1a.2 to 64 uhci_hcd 0000:00:1a.2: UHCI Host Controller uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.2: irq 20, io base 0x0000c0a0 PM: Adding info for usb:usb3 PM: Adding info for No Bus:usbdev3.1_ep00 usb usb3: configuration #1 chosen from 1 choice PM: Adding info for usb:3-0:1.0 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev3.1_ep81 GSI 21 sharing vector 0xD8 and IRQ 21 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.0: irq 21, io base 0x0000c080 PM: Adding info for usb:usb4 PM: Adding info for No Bus:usbdev4.1_ep00 usb usb4: configuration #1 chosen from 1 choice PM: Adding info for usb:4-0:1.0 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev4.1_ep81 ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000c060 PM: Adding info for usb:usb5 PM: Adding info for No Bus:usbdev5.1_ep00 usb usb5: configuration #1 chosen from 1 choice PM: Adding info for usb:5-0:1.0 hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usb 2-2: new low speed USB device using uhci_hcd and address 2 PM: Adding info for No Bus:usbdev5.1_ep81 ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000c040 PM: Adding info for usb:usb6 PM: Adding info for No Bus:usbdev6.1_ep00 usb usb6: configuration #1 chosen from 1 choice PM: Adding info for usb:6-0:1.0 hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev6.1_ep81 ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7 ehci_hcd 0000:00:1a.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1a.7 ehci_hcd 0000:00:1a.7: irq 20, io mem 0xd0326c00 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 PM: Adding info for usb:usb7 PM: Adding info for No Bus:usbdev7.1_ep00 usb usb7: configuration #1 chosen from 1 choice PM: Adding info for usb:7-0:1.0 hub 7-0:1.0: USB hub found hub 7-0:1.0: 6 ports detected usb 2-2: string descriptor 0 read error: -71 usb 2-2: string descriptor 0 read error: -71 PM: Adding info for usb:2-2 PM: Adding info for No Bus:usbdev2.2_ep00 usb 2-2: configuration #1 chosen from 1 choice usb 2-2: can't set config #1, error -71 usb 2-2: USB disconnect, address 2 PM: Removing info for No Bus:usbdev2.2_ep00 PM: Removing info for usb:2-2 PM: Adding info for No Bus:usbdev7.1_ep81 ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 21, io mem 0xd0326800 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 PM: Adding info for usb:usb8 PM: Adding info for No Bus:usbdev8.1_ep00 usb usb8: configuration #1 chosen from 1 choice PM: Adding info for usb:8-0:1.0 hub 8-0:1.0: USB hub found hub 8-0:1.0: 6 ports detected PM: Adding info for No Bus:usbdev8.1_ep81 ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:03:00.0 to 64 e1000: 0000:03:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:1b:21:1b:c9:28 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 21 (level, low) -> IRQ 19 e1000: 0000:04:00.0: e1000_probe: (PCI:33MHz:32-bit) 00:07:e9:1a:4d:5f e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection ahci 0000:00:1f.2: version 2.0 ACPI: PCI Interrupt 0000:00:1f.2[B] -> <6>GSI 22 sharing vector 0x21 and IRQ 22 ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 22 (level, low) -> IRQ 22 PM: Adding info for ieee1394:fw-host0 GSI 19 (level, low) -> IRQ 18 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[22] MMIO=[d0160000-d01607ff] Max Packet=[2048] IR/IT contexts=[8/8] usb 2-2: new low speed USB device using uhci_hcd and address 3 PM: Adding info for usb:2-2 PM: Adding info for No Bus:usbdev2.3_ep00 usb 2-2: configuration #1 chosen from 1 choice PM: Adding info for usb:2-2:1.0 PM: Adding info for No Bus:usbdev2.3_ep81 PM: Adding info for usb:2-2:1.1 PM: Adding info for No Bus:usbdev2.3_ep82 usbcore: registered new driver hiddev input: CHESEN PS2 to USB Converter as /class/input/input0 input: USB HID v1.10 Keyboard [CHESEN PS2 to USB Converter] on usb-0000:00:1a.1-2 input: CHESEN PS2 to USB Converter as /class/input/input1 input: USB HID v1.10 Mouse [CHESEN PS2 to USB Converter] on usb-0000:00:1a.1-2 usbcore: registered new driver usbhid /usr/src/linux-2.6.18-xen.hg/drivers/usb/input/hid-core.c: v2.6:USB HID core driver PCI: Setting latency timer of device 0000:00:1f.2 to 64 ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl RAID mode ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part ata1: SATA max UDMA/133 cmd 0xFFFFC2000003C100 ctl 0x0 bmdma 0x0 irq 255 ata2: SATA max UDMA/133 cmd 0xFFFFC2000003C180 ctl 0x0 bmdma 0x0 irq 255 ata3: SATA max UDMA/133 cmd 0xFFFFC2000003C200 ctl 0x0 bmdma 0x0 irq 255 ata4: SATA max UDMA/133 cmd 0xFFFFC2000003C280 ctl 0x0 bmdma 0x0 irq 255 ata5: SATA max UDMA/133 cmd 0xFFFFC2000003C300 ctl 0x0 bmdma 0x0 irq 255 ata6: SATA max UDMA/133 cmd 0xFFFFC2000003C380 ctl 0x0 bmdma 0x0 irq 255 scsi0 : ahci PM: Adding info for No Bus:host0 PM: Adding info for ieee1394:009027000229db39 ieee1394: Host added: ID:BUS[0-00:1023] GUID[009027000229db39] PM: Adding info for ieee1394:009027000229db39-0 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATAPI, max UDMA/100 ata1.00: configured for UDMA/100 scsi1 : ahci PM: Adding info for No Bus:host1 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-8, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 31/32) ata2.00: ata2: dev 0 multi count 0 ata2.00: configured for UDMA/133 scsi2 : ahci PM: Adding info for No Bus:host2 ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-8, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 31/32) ata3.00: ata3: dev 0 multi count 0 ata3.00: configured for UDMA/133 scsi3 : ahci PM: Adding info for No Bus:host3 ata4: SATA link down (SStatus 0 SControl 300) scsi4 : ahci PM: Adding info for No Bus:host4 ata5: SATA link down (SStatus 0 SControl 300) scsi5 : ahci PM: Adding info for No Bus:host5 ata6: SATA link down (SStatus 0 SControl 300) PM: Adding info for No Bus:target0:0:0 Vendor: TSSTcorp Model: CDDVDW SH-S223F Rev: SB00 Type: CD-ROM ANSI SCSI revision: 05 PM: Adding info for scsi:0:0:0:0 PM: Adding info for No Bus:target1:0:0 Vendor: ATA Model: Hitachi HDP72502 Rev: GM2O Type: Direct-Access ANSI SCSI revision: 05 PM: Adding info for scsi:1:0:0:0 SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sd 1:0:0:0: Attached scsi disk sda PM: Adding info for No Bus:target2:0:0 Vendor: ATA Model: Hitachi HDP72502 Rev: GM2O Type: Direct-Access ANSI SCSI revision: 05 PM: Adding info for scsi:2:0:0:0 SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back sdb: sdb1 sdb2 sdb3 sd 2:0:0:0: Attached scsi disk sdb Probing IDE interface ide0... Probing IDE interface ide1... md: md0 stopped. md: bind md: bind raid1: raid set md0 active with 2 out of 2 mirrors md: md1 stopped. md: bind md: bind raid1: raid set md1 active with 2 out of 2 mirrors device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@xxxxxxxxxx kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. ts: Compaq touchscreen protocol output eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) input: PC Speaker as /class/input/input2 sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 0:0:0:0: Attached scsi CD-ROM sr0 ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:00:1b.0 to 64 sr 0:0:0:0: Attached scsi generic sg0 type 5 sd 1:0:0:0: Attached scsi generic sg1 type 0 sd 2:0:0:0: Attached scsi generic sg2 type 0 Too many connections hda-intel: no codecs initialized ACPI: PCI interrupt for device 0000:00:1b.0 disabled ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 20 PM: Adding info for No Bus:i2c-0 Adding 7815612k swap on /dev/sda2. Priority:-1 extents:1 across:7815612k Adding 7815612k swap on /dev/sdb2. Priority:-2 extents:1 across:7815612k EXT3 FS on dm-0, internal journal ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) ieee1394: sbp2: Try serialize_io=0 for better performance kjournald starting. Commit interval 5 seconds EXT3 FS on md0, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on dm-2, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on dm-1, internal journal EXT3-fs: mounted filesystem with ordered data mode. e1000: eth2: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] ACPI: Power Button (CM) [PWRB] pnp: the driver 'parport_pc' has been registered parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP] parport0: irq 5 detected lp0: using parport0 (polling). lp0: console ready ppdev: user-space parallel port driver NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver Bridge firewalling registered ADDRCONF(NETDEV_UP): peth2: link is not ready e1000: peth2: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex ADDRCONF(NETDEV_CHANGE): peth2: link becomes ready device peth2 entered promiscuous mode audit(1226581459.847:2): dev=peth2 prom=256 old_prom=0 auid=4294967295 eth2: port 1(peth2) entering learning state eth2: topology change detected, propagating eth2: port 1(peth2) entering forwarding state suspend: event channel 26 Linux agpgart interface v0.101 (c) Dave Jones fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. fglrx: Unknown symbol xen_invlpg_mask peth2: no IPv6 routers present eth2: no IPv6 routers present