|
|
|
|
|
|
|
|
|
|
xen-users
Re: [Xen-users] two bridges with xen 3.2.0
Hi,
i'm sorry guys, i don't quite get it.
i replaced my script with this one:
***********
#!/bin/sh
XENDIR="/etc/xen/scripts"
$XENDIR/network-bridge "$@" netdev=eth0 bridge=eth0 vifnum=0
$XENDIR/network-bridge "$@" netdev=eth1 bridge=eth1 vifnum=1
***********
on the other hand....
what about /etc/xen/xend-config.sxp ? Do i have to keep the (vif-script
vif-bridge) line? Do i have to use another script?
what about /etc/network/interfaces? can i use something like this?
****************
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
address 192.168.1.200
netmask 255.255.255.0
network 192.168.1.0
broadcast 192.168.1.255
gateway 192.168.1.231
auto eth1
iface eth1 inet static
address 192.168.2.200
netmask 255.255.255.0
****************
or do i have to replace eth0 with peth0 in this file? will debian load
the newtork interfaces if i change the name?
Thank you.
En/na Gareth Bult ha escrit:
Hi,
Here's my Xen3.2 script .. working 100% on multiple boxes ...
#!/bin/sh
XENDIR="/etc/xen/scripts"
$XENDIR/network-bridge "$@" netdev=eth0 bridge=eth0 vifnum=0
$XENDIR/network-bridge "$@" netdev=eth1 bridge=eth1 vifnum=1
NOTE::
The nice people at Xen changed the default bridge from Xenbr<n> to eth<n>.
New method;
a. rename device eth0 to peth0
b. create a bridge called eth0 (!!)
c. include peth0 as a device for bridge eth0
!!
Much improved method, however, the documentation stinks ..
Gareth.
----- Original Message -----
step 3.: "Jordi Moles" <jordi@xxxxxxxxx>
To: xen-users@xxxxxxxxxxxxxxxxxxx
Sent: 20 February 2008 11:50:33 o'clock (GMT) Europe/London
Subject: [Xen-users] two bridges with xen 3.2.0
hi,
i'm trying the new 3.2.0.
i've always used two bridges since 3.0.x with the following set up:
Replace
(network-script network-bridge)
with
(network-script network-bridge-both)
in file /etc/xen/xend-config.sxp
The content of network-bridge-both is
************
#!/bin/sh
dir=$(dirname "$0")
"$dir/network-bridge" "$@" vifnum=0 netdev=eth0 bridge=xenbr0
"$dir/network-bridge" "$@" vifnum=1 netdev=eth1 bridge=xenbr1
************
As i said, this used to work for 3.0.x and 3.1.x releases.....
Now, it doesn't work anymore...
when the xen loads....
there's only this in the ifconfig command:
-lo
-peth0
-peth1
What's different from the earlier releases? Thank you.
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
|
|
|
|