Daniel P. Berrange wrote:
On Fri, May 11, 2007 at 12:12:52PM +0100, Richard W.M. Jones wrote:
'service xend start' is failing in the network-bridge script. It fails
in such a way as to kill the network completely and leave tmpbridge around.
Can you capture
ifconfig -a
brctl show
ip route show
Before & after doing the service xend start.
Attached are:
brctl.before.txt brctl show (before)
ifconfig.before.txt ifconfig -a (before)
ip-route.before.txt ip route show (before)
Then after I did service xend start:
brctl.after.txt brctl show (after)
ifconfig.after.txt ifconfig -a (after)
ip-route.after.txt ip route show (after)
and xend-config.sxp.
One thing that's a bit strange is the sudden presence of virbr0. I
don't understand where it comes from. Note: there is no libvirtd or
qemu running on this machine.
Rich.
--
Emerging Technologies, Red Hat - http://et.redhat.com/~rjones/
Registered Address: Red Hat UK Ltd, Amberley Place, 107-111 Peascod Street,
Windsor, Berkshire, SL4 1TE, United Kingdom. Registered in England and
Wales
under Company Registration No. 03798903
bridge name bridge id STP enabled interfaces
eth0 Link encap:Ethernet HWaddr 00:E0:81:74:02:28
inet addr:192.168.2.4 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::2e0:81ff:fe74:228/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:193 errors:0 dropped:0 overruns:0 frame:0
TX packets:232 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:25570 (24.9 KiB) TX bytes:25670 (25.0 KiB)
Interrupt:17 Base address:0xa000
eth1 Link encap:Ethernet HWaddr 00:E0:81:74:02:29
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:16 Base address:0x2000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:560 (560.0 b) TX bytes:560 (560.0 b)
192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.4
169.254.0.0/16 dev eth0 scope link
default via 192.168.2.1 dev eth0
bridge name bridge id STP enabled interfaces
tmpbridge 8000.000000000000 no
virbr0 8000.000000000000 no
eth1 Link encap:Ethernet HWaddr 00:E0:81:74:02:29
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:16 Base address:0x2000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:560 (560.0 b) TX bytes:560 (560.0 b)
peth0 Link encap:Ethernet HWaddr 00:E0:81:74:02:28
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:198 errors:0 dropped:0 overruns:0 frame:0
TX packets:234 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:25930 (25.3 KiB) TX bytes:25850 (25.2 KiB)
Interrupt:17 Base address:0xa000
tmpbridge Link encap:Ethernet HWaddr 00:00:00:00:00:00
inet addr:192.168.2.4 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:34 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:8762 (8.5 KiB)
virbr0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:4273 (4.1 KiB)
# -*- sh -*-
#
# Xend configuration file.
#
# This example configuration is appropriate for an installation that
# utilizes a bridged network configuration. Access to xend via http
# is disabled.
# Commented out entries show the default for that entry, unless otherwise
# specified.
#(logfile /var/log/xen/xend.log)
#(loglevel DEBUG)
# The Xen-API server configuration. (Please note that this server is
# available as an UNSUPPORTED PREVIEW in Xen 3.0.4, and should not be relied
# upon).
#
# This value configures the ports, interfaces, and access controls for the
# Xen-API server. Each entry in the list starts with either unix, a port
# number, or an address:port pair. If this is "unix", then a UDP socket is
# opened, and this entry applies to that. If it is a port, then Xend will
# listen on all interfaces on that TCP port, and if it is an address:port
# pair, then Xend will listen on the specified port, using the interface with
# the specified address.
#
# The subsequent string configures the user-based access control for the
# listener in question. This can be one of "none" or "pam", indicating either
# that users should be allowed access unconditionally, or that the local
# Pluggable Authentication Modules configuration should be used. If this
# string is missing or empty, then "pam" is used.
#
# The final string gives the host-based access control for that listener. If
# this is missing or empty, then all connections are accepted. Otherwise,
# this should be a space-separated sequence of regular expressions; any host
# with a fully-qualified domain name or an IP address that matches one of
# these regular expressions will be accepted.
#
# Example: listen on TCP port 9363 on all interfaces, accepting connections
# only from machines in example.com or localhost, and allow access through
# the unix domain socket unconditionally:
#
# (xen-api-server ((9363 pam '^localhost$ example\\.com$')
# (unix none)))
#
# Optionally, the TCP Xen-API server can use SSL by specifying the private
# key and certificate location:
#
# (9367 pam '' /etc/xen/xen-api.key /etc/xen/xen-api.crt)
#
# Default:
# (xen-api-server ((unix)))
#(xend-http-server no)
(xend-unix-server yes)
#(xend-tcp-xmlrpc-server no)
#(xend-unix-xmlrpc-server yes)
#(xend-relocation-server no)
# The relocation server should be kept desactivated unless using a trusted
# network, the domain virtual memory will be exchanged in raw form without
# encryption of the communication. See also xend-relocation-hosts-allow option
(xend-unix-path /var/lib/xend/xend-socket)
# Address and port xend should use for the legacy TCP XMLRPC interface,
# if xen-tcp-xmlrpc-server is set.
#(xen-tcp-xmlrpc-server-address 'localhost')
#(xen-tcp-xmlrpc-server-port 8006)
# SSL key and certificate to use for the legacy TCP XMLRPC interface.
# Setting these will mean that this port serves only SSL connections as
# opposed to plaintext ones.
#(xend-tcp-xmlrpc-server-ssl-key-file /etc/xen/xmlrpc.key)
#(xend-tcp-xmlrpc-server-ssl-cert-file /etc/xen/xmlrpc.crt)
# Port xend should use for the HTTP interface, if xend-http-server is set.
#(xend-port 8000)
# Port xend should use for the relocation interface, if xend-relocation-server
# is set.
#(xend-relocation-port 8002)
# Address xend should listen on for HTTP connections, if xend-http-server is
# set.
# Specifying 'localhost' prevents remote connections.
# Specifying the empty string '' (the default) allows all connections.
#(xend-address '')
#(xend-address localhost)
# Address xend should listen on for relocation-socket connections, if
# xend-relocation-server is set.
# Meaning and default as for xend-address above.
#(xend-relocation-address '')
# The hosts allowed to talk to the relocation port. If this is empty (the
# default), then all connections are allowed (assuming that the connection
# arrives on a port and interface on which we are listening; see
# xend-relocation-port and xend-relocation-address above). Otherwise, this
# should be a space-separated sequence of regular expressions. Any host with
# a fully-qualified domain name or an IP address that matches one of these
# regular expressions will be accepted.
#
# For example:
# (xend-relocation-hosts-allow '^localhost$ ^.*\\.example\\.org$')
#
#(xend-relocation-hosts-allow '')
(xend-relocation-hosts-allow '^localhost$ ^localhost\\.localdomain$')
# The limit (in kilobytes) on the size of the console buffer
#(console-limit 1024)
##
# To bridge network traffic, like this:
#
# dom0: ----------------- bridge -> real eth0 -> the network
# |
# domU: fake eth0 -> vifN.0 -+
#
# use
#
# (network-script network-bridge)
#
# Your default ethernet device is used as the outgoing interface, by default.
# To use a different one (e.g. eth1) use
#
# (network-script 'network-bridge netdev=eth1')
#
# The bridge is named xenbr0, by default. To rename the bridge, use
#
# (network-script 'network-bridge bridge=<name>')
#
# It is possible to use the network-bridge script in more complicated
# scenarios, such as having two outgoing interfaces, with two bridges, and
# two fake interfaces per guest domain. To do things like this, write
# yourself a wrapper script, and call network-bridge from it, as appropriate.
#
(network-script network-bridge)
#### LAPTOP USERS ! #####
# For laptops, or machines where network interfaces come/go on-the-fly,
# or are otherwise managed by NetworkManager, comment out the above line.
# Then, uncomment the line below, and use libvirt's virtual networking
# capability which sets up a isolated bridge + NAT forwarding
#(network-script /bin/true)
#### LAPTOP USERS ! #####
# The script used to control virtual interfaces. This can be overridden on a
# per-vif basis when creating a domain or a configuring a new vif. The
# vif-bridge script is designed for use with the network-bridge script, or
# similar configurations.
#
# If you have overridden the bridge name using
# (network-script 'network-bridge bridge=<name>') then you may wish to do the
# same here. The bridge name can also be set when creating a domain or
# configuring a new vif, but a value specified here would act as a default.
#
# If you are using only one bridge, the vif-bridge script will discover that,
# so there is no need to specify it explicitly.
#
(vif-script vif-bridge)
## Use the following if network traffic is routed, as an alternative to the
# settings for bridged networking given above.
# NB: Obsolete. See note above for LAPTOP USERS
#(network-script network-route)
#(vif-script vif-route)
## Use the following if network traffic is routed with NAT, as an alternative
# to the settings for bridged networking given above.
# NB: Obsolete. See note above for LAPTOP USERS
#(network-script network-nat)
#(vif-script vif-nat)
# Dom0 will balloon out when needed to free memory for domU.
# dom0-min-mem is the lowest memory level (in MB) dom0 will get down to.
# If dom0-min-mem=0, dom0 will never balloon out.
(dom0-min-mem 256)
# In SMP system, dom0 will use dom0-cpus # of CPUS
# If dom0-cpus = 0, dom0 will take all cpus available
(dom0-cpus 0)
# Whether to enable core-dumps when domains crash.
#(enable-dump no)
# The tool used for initiating virtual TPM migration
#(external-migration-tool '')
# The interface for VNC servers to listen on. Defaults
# to 127.0.0.1 To restore old 'listen everywhere' behaviour
# set this to 0.0.0.0
#(vnc-listen '127.0.0.1')
# The default password for VNC console on HVM domain.
# Empty string is no authentication.
(vncpasswd '')
smime.p7s
Description: S/MIME Cryptographic Signature
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
Home