| |
|
 |
|
 |
|
|
|
| |
|
|
xen-users
Re: [Xen-users] No networkcard with Xen2.0.6 (3C940)
I'm not an Ubuntu user but I would think all you would need to do is to
create a /etc/sysconfig/network-scripts/ifcfg-eth0(or Ubuntu equiv.) and
set the network to start on boot with 'service network on' or the Ubuntu
equivalent.
here's an example ifcfg-eth0 ..
DEVICE=eth0
BOOTPROTO=static
IPADDR=192.168.0.2
NETMASK=255.255.255.0
NETWORK=192.168.0.0
BROADCAST=192.168.0.255
ONBOOT=yes
Hope this help some :)
John Fairbairn
> Hi again,
>
> my problem is nearly solved.
> As I described I saw the driver beeing compiled (yes it was sk98lin) but
> was wondering why I have no eth0 while booting xen0.
> ifconfig showed only the lo device.
>
> An ifconfig eth0 up solved the problem
> and I could configure my card.
>
> But I have to run ifconfig everytime I restart my xen0 System.
> Don't get me wrong I have prevously configured my eth0 Card before
> installing xen.
> So what am I doing wrong here.
> Am I missing something?
>
> Kind Regards
> Dennis Erlach
>
>>I use this same network and when I was using xen stable there was no
>>problem with it. But I would say what is going on is this: when you run
>>make world, it cleans your kernel tree and everything else that was
>>compiled before in your xen dir, so it erases your .config that had this
>>module (or bultin). After you change options for xen0 kernel, do make
>>dist or make kbuild at xen main dir, then install with ./install.sh or
>>make install. If you are really sure it compiled within the xen0 kernel
>>(I doubt this if you ran make world) try loading (module: sk98lin).
>>
>>On Tue, 2005-05-31 at 12:06 +0200, opensource@xxxxxx wrote:
>>
>>
>>>Hi List,
>>>
>>>I have an installtion of Ubuntu 5.04 and try to get Xen running.
>>>Xen boots fine except that an ifconfig tells me only the loopback device
>>>is present.
>>>I think the driver for my OnBoard Networkcard 3C940 is not built in.
>>>Can anyone tell me how to solve this issue?
>>>
>>>I have tried to compile form source which has the same result.
>>>
>>>I tried to prepare the Kernel for me like the Documentation told me:
>>>" make ARCH=xen xconfig "
>>>I selected the Yukon Marvel Driver which supports the 3C940 Card.
>>>a " cd .. " and " make " gives me the output that there is no rule for
>>> make.
>>>I also edited the defconfig file for xen0. make world compiles fine. I
>>>see the driver during compiling.
>>>
>>>But still the same issue.
>>>
>>>Please anyone help me.
>>>
>>>Kind Regards
>>>Dennis Erlach
>>>
>>>_______________________________________________
>>>Xen-users mailing list
>>>Xen-users@xxxxxxxxxxxxxxxxxxx
>>>http://lists.xensource.com/xen-users
>>>
>>>
>>
>>
>>_______________________________________________
>>Xen-users mailing list
>>Xen-users@xxxxxxxxxxxxxxxxxxx
>>http://lists.xensource.com/xen-users
>>
>>
>>
>>
>
>
> _______________________________________________
> Xen-users mailing list
> Xen-users@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-users
>
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
|
|
| |
|
Home