On Thu, Mar 04, 2010 at 12:18:19PM +0800, Cui, Dexuan wrote:
> Thank Jan Beulich for pointing this out
You need more than that.
Here is what I see
(XEN) Enabling APIC mode: Phys. Using 3 I/O APICs
(XEN) ACPI: HPET id: 0x8086a301 base: 0xfed00000
(XEN) [VT-D]dmar.c:637: Host address width 40
(XEN) [VT-D]dmar.c:646: found ACPI_DMAR_DRHD:
(XEN) [VT-D]dmar.c:379: dmaru->address = fe710000
(XEN) [VT-D]dmar.c:336: IOAPIC: 0:1f.7
(XEN) [VT-D]dmar.c:391: flags: INCLUDE_ALL
So one DRHD for three IOAPICs. In Linux kernel it would turn off x2APIC
(XEN) [VT-D]dmar.c:650: found ACPI_DMAR_RMRR:
(XEN) [VT-D]dmar.c:331: endpoint: 0:1d.0
(XEN) [VT-D]dmar.c:331: endpoint: 0:1d.1
(XEN) [VT-D]dmar.c:331: endpoint: 0:1d.2
(XEN) [VT-D]dmar.c:331: endpoint: 0:1d.7
(XEN) [VT-D]dmar.c:331: endpoint: 0:1a.0
(XEN) [VT-D]dmar.c:331: endpoint: 0:1a.1
(XEN) [VT-D]dmar.c:331: endpoint: 0:1a.2
(XEN) [VT-D]dmar.c:331: endpoint: 0:1a.7
(XEN) [VT-D]dmar.c:540: RMRR region: base_addr bf3f9000 end_address bf40c548
(XEN) PCI: MCFG configuration 0: base c0000000 segment 0 buses 0 - 255
(XEN) PCI: MCFG area at c0000000 reserved in E820
(XEN) iommu_supports_eim: 1 1 1
(XEN) iommu_supports_eim: 1 1 1
(XEN) Switched to APIC driver x2apic_cluster.
Whoopsie. Here it calls the routine you patched, which just checks to
see if there are DRHDs, but doesn't do a DRHD.count == IOAPCI.count.
(XEN) x2APIC mode enabled.
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 2000.131 MHz processor.
(XEN) Initing memory sharing.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 256K
(XEN) CPU: L3 cache: 8192K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Extended Page Tables (EPT)
(XEN) - Virtual-Processor Identifiers (VPID)
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: ASIDs enabled.
(XEN) HVM: VMX enabled
(XEN) HVM: Hardware Assisted Paging detected.
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Thermal monitoring enabled (TM1)
(XEN) [VT-D]iommu.c:1072: drhd->address = fe710000
(XEN) [VT-D]iommu.c:1073: iommu->reg = ffff82c3fff57000
(XEN) Intel VT-d Snoop Control supported.
(XEN) Intel VT-d DMA Passthrough not supported.
(XEN) Intel VT-d Queued Invalidation supported.
(XEN) Intel VT-d Interrupt Remapping supported.
(XEN) [VT-D]iommu.c:1838: apic:0x0/0x3, 0x0
(XEN) [VT-D]iommu.c:1838: apic:0x1/0x3, 0x2
(XEN) [VT-D]iommu.c:1845: ioapic_to_iommu: ioapic 0x1 (id: 0x2) is NULL! Will
not try to enable Interrupt Remapping.
.. Here later on, it does the check and turns iommu_intr off.
(XEN) Intel VT-d Snoop Control enabled.
(XEN) Intel VT-d DMA Passthrough disabled .
(XEN) Intel VT-d Queued Invalidation enabled.
(XEN) Intel VT-d Interrupt Remapping disabled .
(XEN) Intel VT-D turned on!???
(XEN) IOMMU rc: 0, 1
(XEN) I/O virtualisation enabled
(XEN) I/O virtualisation for PV guests disabled
(XEN) CPU0: Intel Genuine Intel(R) CPU @ 0000 @ 2.00GHz stepping 02
(XEN) Booting processor 1/1 eip 88000
(XEN) Initializing CPU#1
(XEN) x2APIC mode enabled.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
Here is the little debug patch I used
diff -r b8d2a4134a68 xen/drivers/passthrough/iommu.c
--- a/xen/drivers/passthrough/iommu.c Wed Mar 03 17:41:58 2010 +0000
+++ b/xen/drivers/passthrough/iommu.c Fri Mar 05 12:50:36 2010 -0500
@@ -282,6 +282,7 @@
{
rc = iommu_hardware_setup();
iommu_enabled = (rc == 0);
+ printk("IOMMU rc: %d, %d\n", rc, iommu_enabled);
}
if ( force_iommu && !iommu_enabled )
diff -r b8d2a4134a68 xen/drivers/passthrough/vtd/intremap.c
--- a/xen/drivers/passthrough/vtd/intremap.c Wed Mar 03 17:41:58 2010 +0000
+++ b/xen/drivers/passthrough/vtd/intremap.c Fri Mar 05 12:50:36 2010 -0500
@@ -128,9 +128,15 @@
{
struct acpi_drhd_unit *drhd;
+
+ printk("%s: %d %d %d\n", __FUNCTION__,iommu_enabled, iommu_qinval,
iommu_intremap);
+
if ( !iommu_enabled || !iommu_qinval || !iommu_intremap )
return 0;
+ if ( list_empty(&acpi_drhd_units) )
+ return 0;
+
for_each_drhd_unit ( drhd )
if ( !ecap_queued_inval(drhd->ecap) ||
!ecap_intr_remap(drhd->ecap) ||
diff -r b8d2a4134a68 xen/drivers/passthrough/vtd/iommu.c
--- a/xen/drivers/passthrough/vtd/iommu.c Wed Mar 03 17:41:58 2010 +0000
+++ b/xen/drivers/passthrough/vtd/iommu.c Fri Mar 05 12:50:36 2010 -0500
@@ -1834,6 +1834,8 @@
int apic;
for ( apic = 0; apic < nr_ioapics; apic++ )
{
+ dprintk(XENLOG_INFO VTDPREFIX," apic:0x%x/0x%x, 0x%x\n",
+ apic, nr_ioapics, IO_APIC_ID(apic));
if ( ioapic_to_iommu(IO_APIC_ID(apic)) == NULL )
{
iommu_intremap = 0;
@@ -1972,6 +1974,14 @@
if ( init_vtd_hw() )
goto error;
+#define P(p,s) printk("Intel VT-d %s %s.\n", s, (p)? "enabled" : "disabled ")
+ P(iommu_snoop, "Snoop Control");
+ P(iommu_passthrough, "DMA Passthrough");
+ P(iommu_qinval, "Queued Invalidation");
+ P(iommu_intremap, "Interrupt Remapping");
+#undef P
+
+ printk("Intel VT-D turned on!???\n");
register_keyhandler('V', &dump_iommu_info_keyhandler);
return 0;
@@ -1984,6 +1994,7 @@
iommu_passthrough = 0;
iommu_qinval = 0;
iommu_intremap = 0;
+ printk("Intel VT-d is turned off due to errors.\n");
return -ENOMEM;
}
>
> Thanks,
> -- Dexuan
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-devel
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
|
Home