| |
|
 |
|
 |
|
|
|
| |
|
|
xen-users
Re: [Xen-users] Conflict with Xen bridge?
On Wednesday, 26 March 2008 13:01:05 +0100,
Marc Patino Gómez wrote:
> Hi again,
Hi Marc.
> as you can see, on brctl output there is only one virtual interface
> vif0.0, on your xenbr0 bridge, and there isn't any physical interface.
> I advice to put the following config:
copy/paste mistake :-(
bridge name bridge id STP enabled interfaces
xenbr0 8000.feffffffffff no vif0.0
peth1
I'd be consistent with the output of ifconfig which I put below in the
same e-mail :-)
> Create the following file:
>
> /etc/xen/scripts/network-bridge-wrapper
>
> give it permisions to be executable:
>
> Put
>
> #!/bin/sh
> /etc/xen/scripts/network-bridge start bridge=xenbr0 vifnum=0
>
> Change the following line in /etc/xen/xend-config.sxp:
>
> (network-script 'network-bridge netdev=eth1')
>
> for this line
>
> (network-script network-bridge-wrapper)
>
> After this restart your xend daemon, or reboot your box.
>
>
> With this config a brctl show output may be:
>
> sunfire:/home/xxxxxx# brctl show
> bridge name bridge id STP enabled interfaces
> xenbr0 8000.feffffffffff no vif0.0
>
> peth0
I try this configuration, but I don't see up both peth and vif0.0
interfaces:
brctl show
bridge name bridge id STP enabled interfaces
xenbr0 8000.000000000000 no
cat /etc/xen/xend-config.sxp | grep ^[^#]
(network-script network-bridge-wrapper)
(dom0-min-mem 196)
(dom0-cpus 0)
ll /etc/xen/scripts/network-bridge-wrapper
-rwxr-x--- 1 root root 71 2008-03-27 00:52
/etc/xen/scripts/network-bridge-wrapper
cat /etc/xen/scripts/network-bridge-wrapper
#!/bin/sh
/etc/xen/scripts/network-bridge start bridge=xenbr0 vifnum=0
alderamin:~# ifconfig
eth0 Link encap:Ethernet HWaddr 00:18:F3:9D:8C:D8
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3732 errors:0 dropped:0 overruns:0 frame:0
TX packets:4090 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1780249 (1.6 MiB) TX bytes:537354 (524.7 KiB)
Interrupt:17
eth1 Link encap:Ethernet HWaddr 00:18:F3:9D:89:3A
inet addr:10.1.0.10 Bcast:10.1.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4796 errors:0 dropped:0 overruns:0 frame:0
TX packets:4069 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:587242 (573.4 KiB) TX bytes:1809537 (1.7 MiB)
Interrupt:16 Base address:0xe000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:276 (276.0 b) TX bytes:276 (276.0 b)
ppp0 Link encap:Point-to-Point Protocol
inet addr:190.51.122.4 P-t-P:200.51.241.209 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:3569 errors:0 dropped:0 overruns:0 frame:0
TX packets:3927 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:1691867 (1.6 MiB) TX bytes:446009 (435.5 KiB)
xenbr0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
> so... change the line in the file
> /etc/xen/scripts/network-bridge-wrapper as your needs, also you can put
> more lines to create more bridges, you can make very cool configs with
> xen networking :)
> I hope it will be useful.
Thanks for your reply.
Regards,
Daniel
--
Fingerprint: BFB3 08D6 B4D1 31B2 72B9 29CE 6696 BF1B 14E6 1D37
Powered by Debian GNU/Linux Lennt - Linux user #188.598
signature.asc
Description: Digital signature
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
|
|
|
| |
|
Home