[Xen-users] Error creating domain U.

Hi list,

I was trying to install fully virtualised domU(Fedora 7 ) on xen 3.1 with Fedora 7 as the dom0 (host).
The domain creation stop at the following step :

Attached is a screen dump .

Then I tried to run the domain with "pci=routeirq" option.
But that also stops after some steps.
( I have tried with other options such as "nolapic" , "notsc" , "clocksource=pit" "clock=pit" , but with no success)

Here is a screen dump after specifing "pci=routeirq".

Here is a complete list of all the logs and system info.
My machine is HP Workstation xw4400, with Intel core 2 duo processor.

What else I can do to install the domU.
Please help !!!

Regards,
Vijay shankar Yadav.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

$ xm dmesg
[?1034h __ __            _____ _   ___             _____ __     _____
\ \/ /___ _ __   |___ / / | / _ \    _ __ __|___ |/ _| __|___ |
\ // _ \ \047_ \    |_ \ | || | | |__| \047__/ __| / /| |_ / __| / /
/ \ __/ | | | ___) || || |_| |__| | | (__ / /_| _| (__ / /
/_/\_\___|_| |_| |____(_)_(_)___/   |_| \___/_/(_)_| \___/_/

http://www.cl.cam.ac.uk/netos/xen
University of Cambridge Computer Laboratory

Xen version 3.1.0-rc7-2936.fc7 (kojibuilder@(none)) (gcc version 4.1.2 20070502 (Red Hat 4.1.2-12)) Fri Sep 21 12:06:08 EDT 2007
Latest ChangeSet: unavailable

(XEN) Command line: /xen.gz-2.6.20-2936.fc7 dom0_mem=400M
(XEN) 0000000000000000 - 0000000000099000 (usable)
(XEN) 0000000000099000 - 00000000000a0000 (reserved)
(XEN) 00000000000e8000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 000000003ffc6000 (usable)
(XEN) 000000003ffc6300 - 0000000040000000 (reserved)
(XEN) 00000000f0000000 - 00000000f4000000 (reserved)
(XEN) 00000000fec00000 - 00000000fed40000 (reserved)
(XEN) 00000000fed45000 - 0000000100000000 (reserved)
(XEN) System RAM: 1023MB (1047932kB)
(XEN) Xen heap: 10MB (10240kB)
(XEN) Domain heap initialised: DMA width 32 bits
(XEN) PAE enabled, limit: 16 GB
(XEN) Processor #0 6:15 APIC version 20
(XEN) Processor #1 6:15 APIC version 20
(XEN) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Detected 1866.780 MHz processor.
(XEN) HVM: VMX enabled
(XEN) VMX: MSR intercept bitmap enabled
(XEN) CPU0: Intel(R) Core(TM)2 CPU          6300 @ 1.86GHz stepping 02
(XEN) Mapping cpu 0 to node 255
(XEN) Booting processor 1/1 eip 90000
(XEN) Mapping cpu 1 to node 255
(XEN) CPU1: Intel(R) Core(TM)2 CPU          6300 @ 1.86GHz stepping 02
(XEN) Total of 2 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) Platform timer is 14.318MHz HPET
(XEN) Brought up 2 CPUs
(XEN) *** LOADING DOMAIN 0 ***
(XEN) elf_parse_binary: phdr: paddr=0xc1000000 memsz=0x2c4680
(XEN) elf_parse_binary: phdr: paddr=0xc12c5000 memsz=0x323000
(XEN) elf_parse_binary: memory: 0xc1000000 -> 0xc15e8000
(XEN) elf_xen_parse_note: GUEST_OS = "linux"
(XEN) elf_xen_parse_note: GUEST_VERSION = "2.6"
(XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0"
(XEN) elf_xen_parse_note: VIRT_BASE = 0xc0000000
(XEN) elf_xen_parse_note: PADDR_OFFSET = 0xc0000000
(XEN) elf_xen_parse_note: ENTRY = 0xc1000000
(XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xc1001000
(XEN) elf_xen_parse_note: HV_START_LOW = 0xf5800000
(XEN) elf_xen_parse_note: FEATURES = "writable_page_tables|writable_descriptor_tables|auto_translated_physmap|pae_pgdir_above_4gb|supervisor_mode_kernel"
(XEN) elf_xen_parse_note: PAE_MODE = "yes"
(XEN) elf_xen_parse_note: unknown xen elf note (0xd)
(XEN) elf_xen_parse_note: LOADER = "generic"
(XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1
(XEN) elf_xen_addr_calc_check: addresses:
(XEN)     virt_base        = 0xc0000000
(XEN)     elf_paddr_offset = 0xc0000000
(XEN)     virt_offset      = 0x0
(XEN)     virt_kstart      = 0xc1000000
(XEN)     virt_kend        = 0xc15e8000
(XEN)     virt_entry       = 0xc1000000
(XEN) Xen kernel: 32-bit, PAE, lsb
(XEN) Dom0 kernel: 32-bit, PAE, lsb, paddr 0xc1000000 -> 0xc15e8000
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.:   000000003c000000->000000003e000000 (94208 pages to be allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: c1000000->c15e8000
(XEN) Init. ramdisk: c15e8000->c1e74000
(XEN) Phys-Mach map: c1e74000->c1ed8000
(XEN) Start info:    c1ed8000->c1ed846c
(XEN) Page tables:   c1ed9000->c1eee000
(XEN) Boot stack:    c1eee000->c1eef000
(XEN) TOTAL:         c0000000->c2000000
(XEN) ENTRY ADDRESS: c1000000
(XEN) Dom0 has maximum 2 VCPUs
(XEN) elf_load_binary: phdr 0 at 0xc1000000 -> 0xc12c4680
(XEN) elf_load_binary: phdr 1 at 0xc12c5000 -> 0xc133fb64
(XEN) Initrd len 0x88c000, start at 0xc15e8000
(XEN) Scrubbing Free RAM: ......done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: Errors and warnings
(XEN) Guest Loglevel: Nothing (Rate-limited: Errors and warnings)
(XEN) Xen is relinquishing VGA console.
(XEN) *** Serial input -> DOM0 (type \047CTRL-a\047 three times to switch input to Xen).

$ dmesg
Linux version 2.6.20-2936.fc7xen (kojibuilder@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.1.2 20070502 (Red Hat 4.1.2-12)) #1 SMP Fri Sep 21 12:07:35 EDT 2007
BIOS-provided physical RAM map:
sanitize start
sanitize bail 0
copy_e820_map() start: 0000000000000000 size: 0000000019800000 end: 0000000019800000 type: 1
Xen: 0000000000000000 - 0000000019800000 (usable)
0MB HIGHMEM available.
408MB LOWMEM available.
NX (Execute Disable) protection: active
Entering add_active_range(0, 0, 104448) 0 entries of 256 used
Zone PFN ranges:
DMA             0 ->   104448
Normal     104448 ->   104448
HighMem    104448 ->   104448
early_node_map[1] active PFN ranges
    0:        0 ->   104448
On node 0 totalpages: 104448
DMA zone: 816 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 103632 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
HighMem zone: 0 pages used for memmap
found SMP MP-table at 000f9bf0
DMI 2.4 present.
ACPI: RSDP (v000 COMPAQ                                ) @ 0x000e7810
ACPI: RSDT (v001 HPQOEM SLIC-WKS 0x20060404 0x00000000) @ 0x3ffc6340
ACPI: FADT (v001 COMPAQ GLENWOOD 0x00000001 0x00000000) @ 0x3ffc63ec
ACPI: MADT (v001 COMPAQ GLENWOOD 0x00000001 0x00000000) @ 0x3ffc6460
ACPI: ASF! (v032 COMPAQ GLENWOOD 0x00000001 0x00000000) @ 0x3ffc64e4
ACPI: MCFG (v001 COMPAQ GLENWOOD 0x00000001 0x00000000) @ 0x3ffc6547
ACPI: TCPA (v001 COMPAQ GLENWOOD 0x00000001 0x00000000) @ 0x3ffc6583
ACPI: HPET (v001 COMPAQ GLENWOOD 0x00000001 0x00000000) @ 0x3ffc672b
ACPI: DSDT (v001 COMPAQ DSDT_PRJ 0x00000001 MSFT 0x0100000e) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Detected 1866.877 MHz processor.
Built 1 zonelists. Total pages: 103632
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c1364000 soft=c1344000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Xen reported: 1866.780 MHz processor.
Console: colour VGA+ 80x50
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES:    8
... MAX_LOCK_DEPTH:          30
... MAX_LOCKDEP_KEYS:        2048
... CLASSHASH_SIZE:           1024
... MAX_LOCKDEP_ENTRIES:     8192
... MAX_LOCKDEP_CHAINS:      16384
... CHAINHASH_SIZE:          8192
memory used by lock dependency info: 1064 kB
per task-struct memory footprint: 1200 bytes
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Software IO TLB enabled:
Aperture:     2 megabytes
Kernel range: c012d000 - c032d000
Address size: 24 bits
vmalloc area: da000000-f4ffe000, maxmem 2d7fe000
Memory: 387328k/417792k available (2045k kernel code, 22016k reserved, 1084k data, 180k init, 0k highmem)
virtual kernel memory layout:
    fixmap : 0xf5315000 - 0xf57fe000   (5028 kB)
    pkmap   : 0xf5000000 - 0xf5200000   (2048 kB)
    vmalloc : 0xda000000 - 0xf4ffe000   ( 431 MB)
    lowmem : 0xc0000000 - 0xd9800000   ( 408 MB)
      .init : 0xc1313000 - 0xc1340000   ( 180 kB)
      .data : 0xc11ff5c5 - 0xc130e714   (1084 kB)
      .text : 0xc1000000 - 0xc11ff5c5   (2045 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3737.92 BogoMIPS (lpj=7475842)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebd3f1 20100000 00000000 00000000 0000e3bd 00000000 00000001
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: bfebd3f1 20100000 00000000 00003940 0000e3bd 00000000 00000001
Checking 'hlt' instruction... OK.
lockdep: not fixing up alternatives.
ACPI: Core revision 20060707
CPU 1 irqstacks, hard=c1365000 soft=c1345000
ENABLING IO-APIC IRQs
lockdep: not fixing up alternatives.
Brought up 2 CPUs
Initializing CPU#1
sizeof(vma)=88 bytes
sizeof(page)=32 bytes
sizeof(inode)=564 bytes
sizeof(dentry)=156 bytes
sizeof(ext3inode)=800 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=176 bytes
sizeof(task_struct)=2656 bytes
migration_cost=24
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
Setting up standard PCI resources
Allocating PCI resources starting at 50000000 (gap: 40000000:b0000000)
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region f800-f87f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region fa00-fa3f claimed by ICH6 GPIO
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCX1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCX5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCX6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
xen_mem: Initialising balloon driver.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:0c: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0d: ioport range 0x4e00-0x4e01 has been reserved
pnp: 00:0d: ioport range 0x400-0x48f could not be reserved
pnp: 00:0d: ioport range 0xcb0-0xcbf has been reserved
pnp: 00:0d: ioport range 0xf800-0xf87f could not be reserved
pnp: 00:0d: ioport range 0xfa00-0xfa3f has been reserved
pnp: 00:0d: ioport range 0xfc00-0xfc7f has been reserved
pnp: 00:0d: ioport range 0xfc80-0xfcff has been reserved
pnp: 00:0d: ioport range 0xcb0-0xcbf has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 1000-1fff
MEM window: e0500000-e07fffff
PREFETCH window: d0000000-e01fffff
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.4
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.5
IO window: disabled.
MEM window: e0200000-e04fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.4 to 64
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.5 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 7, 524288 bytes)
TCP bind hash table entries: 8192 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 8752k freed
IA-32 Microcode Update Driver: v1.14a-xen <tigran@xxxxxxxxxxx>
audit: initializing netlink socket (disabled)
audit(1193308181.888:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4:pcie00]
Allocate Port Service[0000:00:1c.4:pcie02]
PCI: Setting latency timer of device 0000:00:1c.5 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.5:pcie00]
Allocate Port Service[0000:00:1c.5:pcie02]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [COMPAQ] OemTableId [ CPU_TM2] [20060707]
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, Processor Device is not present [20060707]
Real Time Clock Driver v1.12ac
hpet_acpi_add: no address or irqs in _CRS
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
Xen virtual console successfully installed as ttyS0
Event-channel device installed.
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 180k freed
Write protecting the kernel read-only data: 762k
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 18, io base 0x00002000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 18 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002020
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 20, io base 0x00002040
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 21, io base 0x00002060
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 18, io mem 0xe0a04000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
input: ImPS/2 Logitech Wheel Mouse as /class/input/input2
SCSI subsystem initialized
libata version 2.00 loaded.
ahci 0000:00:1f.2: version 2.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl RAID mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
ata1: SATA max UDMA/133 cmd 0xDA022500 ctl 0x0 bmdma 0x0 irq 22
ata2: SATA max UDMA/133 cmd 0xDA022580 ctl 0x0 bmdma 0x0 irq 22
ata3: SATA max UDMA/133 cmd 0xDA022600 ctl 0x0 bmdma 0x0 irq 22
ata4: SATA max UDMA/133 cmd 0xDA022680 ctl 0x0 bmdma 0x0 irq 22
scsi0 : ahci
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7, max UDMA/100, 156301488 sectors: LBA48 NCQ (depth 31/32)
ata1.00: ata1: dev 0 multi count 0
ata1.00: configured for UDMA/100
scsi1 : ahci
ata2: SATA link down (SStatus 0 SControl 300)
scsi2 : ahci
ata3: SATA link down (SStatus 0 SControl 300)
scsi3 : ahci
ata4: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      Hitachi HDS72168 P21O PQ: 0 ANSI: 5
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
ata_piix 0000:00:1f.1: version 2.00ac7
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata5: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x20A0 irq 14
ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x20A8 irq 15
scsi4 : ata_piix
ata5.00: ATAPI, max UDMA/44
ata5.00: configured for UDMA/44
scsi5 : ata_piix
ATA: abnormal status 0x7F on port 0x177
scsi 4:0:0:0: CD-ROM            TSSTcorp CDW/DVD TS-H492C CB07 PQ: 0 ANSI: 5
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@xxxxxxxxxx
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1193308191.452:2): selinux=0 auid=4294967295
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 4:0:0:0: Attached scsi generic sg1 type 5
input: PC Speaker as /class/input/input3
Floppy drive(s): fd0 is 1.44M
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
FDC 0 is a post-1991 82077
intel_rng: Firmware space is locked read-only. If you can't or
intel_rng: don't want to disable this in firmware setup, and if
intel_rng: you are certain that your system has a functional
intel_rng: RNG, try using the 'no_fwh_detect' option.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
8250_pnp: Unknown symbol serial8250_unregister_port
8250_pnp: Unknown symbol serial8250_register_port
sr0: scsi3-mmc drive: 62x/62x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 4:0:0:0: Attached scsi CD-ROM sr0
tg3.c:v3.72 (January 8, 2007)
ACPI: PCI Interrupt 0000:3f:00.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:3f:00.0 to 64
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
iTCO_vendor_support: vendor-support=0
eth0: Tigon3 [partno(BCM95755) rev a002 PHY(5755)] (PCI Express) 10/100/1000Base-T Ethernet 00:1a:4b:b9:e2:50
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x7860)
iTCO_wdt: heartbeat value must be 2<heartbeat<39 (TCO v1) or 613 (TCO v2), using 30
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
8250_pnp: Unknown symbol serial8250_unregister_port
8250_pnp: Unknown symbol serial8250_register_port
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1b.0 to 64
loop: loaded (max 8 devices)
lp0: using parport0 (interrupt-driven).
lp0: console ready
sonypi: Sony Programmable I/O Controller Driver v1.26.
input: Power Button (FF) as /class/input/input4
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input5
ACPI: Power Button (CM) [PBTN]
No dock devices found.
ibm_acpi: ec object not found
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2031608k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ADDRCONF(NETDEV_UP): eth0: link is not ready
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
audit(1193308236.545:3): audit_pid=1958 old=0 by auid=4294967295
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
Bridge firewalling registered
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3264 buckets, 26112 max)
ADDRCONF(NETDEV_UP): peth0: link is not ready
tg3: peth0: Link is up at 100 Mbps, full duplex.
tg3: peth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready
device peth0 entered promiscuous mode
eth0: port 1(peth0) entering learning state
eth0: topology change detected, propagating
eth0: port 1(peth0) entering forwarding state
virbr0: no IPv6 routers present
peth0: no IPv6 routers present
eth0: no IPv6 routers present
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
device vif1.0 entered promiscuous mode
eth0: port 2(vif1.0) entering learning state
eth0: topology change detected, propagating
eth0: port 2(vif1.0) entering forwarding state
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
device tap0 entered promiscuous mode
eth0: port 3(tap0) entering learning state
eth0: topology change detected, propagating
eth0: port 3(tap0) entering forwarding state
vif1.0: no IPv6 routers present
tap0: no IPv6 routers present
eth0: port 2(vif1.0) entering disabled state
device vif1.0 left promiscuous mode
eth0: port 2(vif1.0) entering disabled state
eth0: port 3(tap0) entering disabled state
device tap0 left promiscuous mode
eth0: port 3(tap0) entering disabled state

$ cat /var/log/xen/xend.log

[2007-10-25 16:00:45 2889] INFO (SrvDaemon:331) Xend Daemon started
[2007-10-25 16:00:45 2889] INFO (SrvDaemon:335) Xend changeset: unavailable.
[2007-10-25 16:00:45 2889] INFO (SrvDaemon:342) Xend version: Unknown.
[2007-10-25 16:00:45 2889] DEBUG (XendDomainInfo:126) XendDomainInfo.recreate({'max_vcpu_id': 1, 'cpu_time': 10949331913L, 'ssidref': 0, 'hvm': 0, 'shutdown_reason': 0, 'dying': 0, 'online_vcpus': 2, 'domid': 0, 'paused': 0, 'crashed': 0, 'running': 1, 'maxmem_kb': 4294967292L, 'shutdown': 0, 'mem_kb': 409600L, 'handle': [0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0], 'blocked': 0, 'name': 'Domain-0'})
[2007-10-25 16:00:45 2889] INFO (XendDomainInfo:143) Recreating domain 0, UUID 00000000-0000-0000-0000-000000000000. at /local/domain/0
[2007-10-25 16:00:45 2889] DEBUG (XendDomainInfo:2026) Storing VM details: {'on_xend_stop': 'ignore', 'shadow_memory': '0', 'uuid': '00000000-0000-0000-0000-000000000000', 'on_reboot': 'restart', 'image': '(linux (kernel ))', 'on_poweroff': 'destroy', 'on_xend_start': 'ignore', 'on_crash': 'restart', 'xend/restart_count': '0', 'vcpus': '2', 'vcpu_avail': '3', 'name': 'Domain-0'}
[2007-10-25 16:00:45 2889] DEBUG (XendDomainInfo:875) Storing domain details: {'name': 'Domain-0', 'console/limit': '1048576', 'memory/target': '409600', 'vm': '/vm/00000000-0000-0000-0000-000000000000', 'domid': '0', 'cpu/0/availability': 'online', 'cpu/1/availability': 'online', 'control/platform-feature-multiprocessor-suspend': '1'}
[2007-10-25 16:00:45 2889] DEBUG (XendDomain:443) Adding Domain: 0
[2007-10-25 16:00:45 2889] DEBUG (XendDomain:379) number of vcpus to use is 0
[2007-10-25 16:00:45 2889] INFO (SrvServer:180) unix path=/var/lib/xend/xend-socket
[2007-10-25 16:00:45 2889] DEBUG (XendDomainInfo:875) Storing domain details: {'name': 'Domain-0', 'console/limit': '1048576', 'memory/target': '409600', 'vm': '/vm/00000000-0000-0000-0000-000000000000', 'domid': '0', 'cpu/0/availability': 'online', 'cpu/1/availability': 'online', 'control/platform-feature-multiprocessor-suspend': '1'}
[2007-10-25 16:00:45 2889] DEBUG (XendDomainInfo:959) XendDomainInfo.handleShutdownWatch
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: VBD.set_device not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: VBD.set_mode not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: VBD.set_type not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: VM.get_auto_power_on not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: VM.set_auto_power_on not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: VM.set_VCPUs_max not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: VM.set_VCPUs_at_startup not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: debug.get_all not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: console.get_other_config not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: console.set_other_config not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: VIF.get_network not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: VIF.set_device not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: VIF.set_MAC not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: VIF.set_MTU not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: session.get_all_records not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: event.get_record not found
[2007-10-25 16:00:45 2889] WARNING (XendAPI:672) API call: event.get_all not found
[2007-10-25 16:01:25 2889] INFO (XMLRPCServer:149) Opening Unix domain socket XML-RPC server on /var/run/xend/xen-api.sock; authentication has been disabled for this server.
[2007-10-25 16:01:25 2889] INFO (XMLRPCServer:149) Opening Unix domain socket XML-RPC server on /var/run/xend/xmlrpc.sock.
[2007-10-25 16:03:08 2889] DEBUG (XendDomainInfo:233) XendDomainInfo.createDormant({'vcpus_params': {}, 'PV_args': '', 'features': '', 'cpus': [], 'devices': {'540019ee-a753-7f8a-8855-6de7d12ba82a': ('vbd', {'uuid': '540019ee-a753-7f8a-8855-6de7d12ba82a', 'bootable': 0, 'driver': 'paravirtualised', 'dev': 'hdc:cdrom', 'uname': 'phy:/dev/dvd', 'mode': 'r'}), '496e4a69-73cb-83cc-6eca-eefb733f97c0': ('vbd', {'uuid': '496e4a69-73cb-83cc-6eca-eefb733f97c0', 'bootable': 1, 'driver': 'paravirtualised', 'dev': 'hda:disk', 'uname': 'file:/disk.imj', 'mode': 'w'}), '808215b3-a5d2-9f29-3660-7c2ccbc8cf73': ('vif', {'bridge': 'eth0', 'mac': '00:16:3e:00:d0:a1', 'type': 'ioemu', 'uuid': '808215b3-a5d2-9f29-3660-7c2ccbc8cf73', 'script': 'vif-bridge'}), '17504bf5-9186-9116-5c78-074b3b706081': ('vkbd', {'uuid': '17504bf5-9186-9116-5c78-074b3b706081'}), 'fe76aa99-4872-d9f8-93f8-51c2dd970433': ('vfb', {'uuid': 'fe76aa99-4872-d9f8-93f8-51c2dd970433', 'keymap': 'en-us', 'type': 'vnc', 'vncdisplay': '0', 'other_config': {'keymap': 'en-us', 'type': 'vnc', 'vncdisplay': '0'}})}, 'vcpu_avail': 1, 'VCPUs_live': 1, 'PV_bootloader': '', 'actions_after_crash': 'restart', 'vbd_refs': ['496e4a69-73cb-83cc-6eca-eefb733f97c0', '540019ee-a753-7f8a-8855-6de7d12ba82a'], 'PV_ramdisk': '', 'is_control_domain': False, 'name_label': 'domU', 'VCPUs_at_startup': 1, 'HVM_boot_params': {'order': 'd'}, 'platform': {'device_model': '/usr/lib/xen/bin/qemu-dm', 'serial': 'pty', 'boot': 'd', 'acpi': '1', 'apic': '1'}, 'cpu_weight': 256, 'console_refs': ['fe76aa99-4872-d9f8-93f8-51c2dd970433'], 'cpu_cap': 0, 'on_xend_stop': 'ignore', 'memory_static_min': 0, 'HVM_boot_policy': 'BIOS order', 'VCPUs_max': 1, 'memory_static_max': 524288000, 'actions_after_shutdown': 'destroy', 'on_xend_start': 'ignore', 'memory_dynamic_max': 419430400, 'actions_after_suspend': '', 'is_a_template': False, 'memory_dynamic_min': 419430400, 'uuid': 'bed29a3d-94d8-c9ee-8f02-3e50de1a65ac', 'PV_kernel': '/usr/lib/xen/boot/hvmloader', 'shadow_memory': 0, 'PV_bootloader_args': '', 'other_config': {}, 'actions_after_reboot': 'restart', 'vif_refs': ['808215b3-a5d2-9f29-3660-7c2ccbc8cf73'], 'vtpm_refs': [], 'security': None})
[2007-10-25 16:03:08 2889] DEBUG (XendDomain:960) Creating new managed domain: domU
[2007-10-25 16:03:18 2889] DEBUG (SrvDomain:76) Starting domain domU False
[2007-10-25 16:03:18 2889] DEBUG (XendDomainInfo:1465) XendDomainInfo.constructDomain
[2007-10-25 16:03:18 2889] DEBUG (balloon:113) Balloon: 618264 KiB free; need 2048; done.
[2007-10-25 16:03:18 2889] DEBUG (XendDomain:443) Adding Domain: 1
[2007-10-25 16:03:18 2889] DEBUG (XendDomainInfo:1519) XendDomainInfo.initDomain: 1 256
[2007-10-25 16:03:18 2889] DEBUG (image:330) args: boot, val: d
[2007-10-25 16:03:18 2889] DEBUG (image:330) args: fda, val: None
[2007-10-25 16:03:18 2889] DEBUG (image:330) args: fdb, val: None
[2007-10-25 16:03:18 2889] DEBUG (image:330) args: soundhw, val: None
[2007-10-25 16:03:18 2889] DEBUG (image:330) args: localtime, val: None
[2007-10-25 16:03:18 2889] DEBUG (image:330) args: serial, val: pty
[2007-10-25 16:03:18 2889] DEBUG (image:330) args: std-vga, val: None
[2007-10-25 16:03:18 2889] DEBUG (image:330) args: isa, val: None
[2007-10-25 16:03:18 2889] DEBUG (image:330) args: acpi, val: 1
[2007-10-25 16:03:18 2889] DEBUG (image:330) args: usb, val: None
[2007-10-25 16:03:18 2889] DEBUG (image:330) args: usbdevice, val: None
[2007-10-25 16:03:18 2889] DEBUG (image:330) args: k, val: None
[2007-10-25 16:03:18 2889] DEBUG (XendDomainInfo:1551) _initDomain:shadow_memory=0x0, memory_static_max=0x1f400000, memory_static_min=0x0.
[2007-10-25 16:03:18 2889] DEBUG (balloon:113) Balloon: 617236 KiB free; need 422912; done.
[2007-10-25 16:03:18 2889] INFO (image:129) buildDomain os=hvm dom=1 vcpus=1
[2007-10-25 16:03:18 2889] DEBUG (image:278) domid          = 1
[2007-10-25 16:03:18 2889] DEBUG (image:279) image          = /usr/lib/xen/boot/hvmloader
[2007-10-25 16:03:18 2889] DEBUG (image:280) store_evtchn   = 2
[2007-10-25 16:03:18 2889] DEBUG (image:281) memsize        = 400
[2007-10-25 16:03:18 2889] DEBUG (image:282) vcpus          = 1
[2007-10-25 16:03:18 2889] DEBUG (image:283) pae            = 0
[2007-10-25 16:03:18 2889] DEBUG (image:284) acpi           = 1
[2007-10-25 16:03:18 2889] DEBUG (image:285) apic           = 1
[2007-10-25 16:03:18 2889] INFO (XendDomainInfo:1367) createDevice: vkbd : {'uuid': '17504bf5-9186-9116-5c78-074b3b706081'}
[2007-10-25 16:03:18 2889] DEBUG (DevController:115) DevController: writing {'state': '1', 'backend-id': '0', 'backend': '/local/domain/0/backend/vkbd/1/0'} to /local/domain/1/device/vkbd/0.
[2007-10-25 16:03:18 2889] DEBUG (DevController:117) DevController: writing {'frontend-id': '1', 'domain': 'domU', 'frontend': '/local/domain/1/device/vkbd/0', 'state': '1', 'online': '1'} to /local/domain/0/backend/vkbd/1/0.
[2007-10-25 16:03:18 2889] INFO (XendDomainInfo:1367) createDevice: vfb : {'uuid': 'fe76aa99-4872-d9f8-93f8-51c2dd970433', 'keymap': 'en-us', 'type': 'vnc', 'vncdisplay': '0', 'other_config': {'keymap': 'en-us', 'type': 'vnc', 'vncdisplay': '0'}}
[2007-10-25 16:03:18 2889] DEBUG (DevController:115) DevController: writing {'state': '1', 'backend-id': '0', 'backend': '/local/domain/0/backend/vfb/1/0'} to /local/domain/1/device/vfb/0.
[2007-10-25 16:03:18 2889] DEBUG (DevController:117) DevController: writing {'domain': 'domU', 'frontend': '/local/domain/1/device/vfb/0', 'uuid': 'fe76aa99-4872-d9f8-93f8-51c2dd970433', 'vncdisplay': '0', 'state': '1', 'keymap': 'en-us', 'online': '1', 'frontend-id': '1', 'type': 'vnc'} to /local/domain/0/backend/vfb/1/0.
[2007-10-25 16:03:18 2889] INFO (XendDomainInfo:1367) createDevice: vbd : {'uuid': '496e4a69-73cb-83cc-6eca-eefb733f97c0', 'bootable': 1, 'driver': 'paravirtualised', 'dev': 'hda:disk', 'uname': 'file:/disk.imj', 'mode': 'w'}
[2007-10-25 16:03:18 2889] DEBUG (DevController:115) DevController: writing {'backend-id': '0', 'virtual-device': '768', 'device-type': 'disk', 'state': '1', 'backend': '/local/domain/0/backend/vbd/1/768'} to /local/domain/1/device/vbd/768.
[2007-10-25 16:03:18 2889] DEBUG (DevController:117) DevController: writing {'domain': 'domU', 'frontend': '/local/domain/1/device/vbd/768', 'uuid': '496e4a69-73cb-83cc-6eca-eefb733f97c0', 'dev': 'hda', 'state': '1', 'params': '/disk.imj', 'mode': 'w', 'online': '1', 'frontend-id': '1', 'type': 'file'} to /local/domain/0/backend/vbd/1/768.
[2007-10-25 16:03:18 2889] INFO (XendDomainInfo:1367) createDevice: vbd : {'uuid': '540019ee-a753-7f8a-8855-6de7d12ba82a', 'bootable': 0, 'driver': 'paravirtualised', 'dev': 'hdc:cdrom', 'uname': 'phy:/dev/dvd', 'mode': 'r'}
[2007-10-25 16:03:18 2889] DEBUG (DevController:115) DevController: writing {'backend-id': '0', 'virtual-device': '5632', 'device-type': 'cdrom', 'state': '1', 'backend': '/local/domain/0/backend/vbd/1/5632'} to /local/domain/1/device/vbd/5632.
[2007-10-25 16:03:18 2889] DEBUG (DevController:117) DevController: writing {'domain': 'domU', 'frontend': '/local/domain/1/device/vbd/5632', 'uuid': '540019ee-a753-7f8a-8855-6de7d12ba82a', 'dev': 'hdc', 'state': '1', 'params': '/dev/dvd', 'mode': 'r', 'online': '1', 'frontend-id': '1', 'type': 'phy'} to /local/domain/0/backend/vbd/1/5632.
[2007-10-25 16:03:18 2889] INFO (XendDomainInfo:1367) createDevice: vif : {'bridge': 'eth0', 'mac': '00:16:3e:00:d0:a1', 'type': 'ioemu', 'uuid': '808215b3-a5d2-9f29-3660-7c2ccbc8cf73', 'script': 'vif-bridge'}
[2007-10-25 16:03:18 2889] DEBUG (DevController:115) DevController: writing {'state': '1', 'backend-id': '0', 'backend': '/local/domain/0/backend/vif/1/0'} to /local/domain/1/device/vif/0.
[2007-10-25 16:03:18 2889] DEBUG (DevController:117) DevController: writing {'bridge': 'eth0', 'domain': 'domU', 'handle': '0', 'uuid': '808215b3-a5d2-9f29-3660-7c2ccbc8cf73', 'script': '/etc/xen/scripts/vif-bridge', 'state': '1', 'frontend': '/local/domain/1/device/vif/0', 'mac': '00:16:3e:00:d0:a1', 'online': '1', 'frontend-id': '1', 'type': 'ioemu'} to /local/domain/0/backend/vif/1/0.
[2007-10-25 16:03:18 2889] INFO (image:445) spawning device models: /usr/lib/xen/bin/qemu-dm ['/usr/lib/xen/bin/qemu-dm', '-d', '1', '-vcpus', '1', '-boot', 'd', '-serial', 'pty', '-acpi', '-domain-name', 'domU', '-net', 'nic,vlan=1,macaddr=00:16:3e:00:d0:a1,model=rtl8139', '-net', 'tap,vlan=1,bridge=eth0', '-vnc', '0', '-vnclisten', '127.0.0.1']
[2007-10-25 16:03:18 2889] INFO (image:449) device model pid: 3737
[2007-10-25 16:03:18 2889] DEBUG (XendDomainInfo:2026) Storing VM details: {'on_xend_stop': 'ignore', 'shadow_memory': '5', 'uuid': 'bed29a3d-94d8-c9ee-8f02-3e50de1a65ac', 'on_reboot': 'restart', 'start_time': '1193308398.49', 'on_poweroff': 'destroy', 'on_xend_start': 'ignore', 'on_crash': 'restart', 'xend/restart_count': '0', 'vcpus': '1', 'vcpu_avail': '1', 'image': '(hvm (kernel /usr/lib/xen/boot/hvmloader) (acpi 1) (apic 1) (boot d) (device_model /usr/lib/xen/bin/qemu-dm) (serial pty) (notes (SUSPEND_CANCEL 1)))', 'name': 'domU'}
[2007-10-25 16:03:18 2889] DEBUG (XendDomainInfo:875) Storing domain details: {'console/port': '3', 'name': 'domU', 'console/limit': '1048576', 'vm': '/vm/bed29a3d-94d8-c9ee-8f02-3e50de1a65ac', 'domid': '1', 'image/suspend-cancel': '1', 'cpu/0/availability': 'online', 'memory/target': '409600', 'control/platform-feature-multiprocessor-suspend': '1', 'store/ring-ref': '102398', 'store/port': '2'}
[2007-10-25 16:03:18 2889] DEBUG (XendDomainInfo:875) Storing domain details: {'name': 'domU', 'console/limit': '1048576', 'image/suspend-cancel': '1', 'domid': '1', 'vm': '/vm/bed29a3d-94d8-c9ee-8f02-3e50de1a65ac', 'cpu/0/availability': 'online', 'memory/target': '409600', 'control/platform-feature-multiprocessor-suspend': '1', 'store/ring-ref': '102398', 'store/port': '2'}
[2007-10-25 16:03:18 2889] DEBUG (XendDomainInfo:959) XendDomainInfo.handleShutdownWatch
[2007-10-25 16:03:18 2889] DEBUG (DevController:148) Waiting for devices vif.
[2007-10-25 16:03:18 2889] DEBUG (DevController:153) Waiting for 0.
[2007-10-25 16:03:18 2889] DEBUG (DevController:558) hotplugStatusCallback /local/domain/0/backend/vif/1/0/hotplug-status.
[2007-10-25 16:03:18 2889] DEBUG (DevController:558) hotplugStatusCallback /local/domain/0/backend/vif/1/0/hotplug-status.
[2007-10-25 16:03:18 2889] DEBUG (DevController:572) hotplugStatusCallback 1.
[2007-10-25 16:03:18 2889] DEBUG (DevController:148) Waiting for devices usb.
[2007-10-25 16:03:18 2889] DEBUG (DevController:148) Waiting for devices vbd.
[2007-10-25 16:03:18 2889] DEBUG (DevController:153) Waiting for 768.
[2007-10-25 16:03:18 2889] DEBUG (DevController:558) hotplugStatusCallback /local/domain/0/backend/vbd/1/768/hotplug-status.
[2007-10-25 16:03:19 2889] DEBUG (DevController:558) hotplugStatusCallback /local/domain/0/backend/vbd/1/768/hotplug-status.
[2007-10-25 16:03:19 2889] DEBUG (DevController:572) hotplugStatusCallback 1.
[2007-10-25 16:03:19 2889] DEBUG (DevController:153) Waiting for 5632.
[2007-10-25 16:03:19 2889] DEBUG (DevController:558) hotplugStatusCallback /local/domain/0/backend/vbd/1/5632/hotplug-status.
[2007-10-25 16:03:19 2889] DEBUG (DevController:572) hotplugStatusCallback 1.
[2007-10-25 16:03:19 2889] DEBUG (DevController:148) Waiting for devices irq.
[2007-10-25 16:03:19 2889] DEBUG (DevController:148) Waiting for devices vkbd.
[2007-10-25 16:03:19 2889] DEBUG (DevController:148) Waiting for devices vfb.
[2007-10-25 16:03:19 2889] DEBUG (vfbif:100) skip waiting for HVM vfb
[2007-10-25 16:03:19 2889] DEBUG (DevController:148) Waiting for devices console.
[2007-10-25 16:03:19 2889] DEBUG (DevController:148) Waiting for devices pci.
[2007-10-25 16:03:19 2889] DEBUG (DevController:148) Waiting for devices ioports.
[2007-10-25 16:03:19 2889] DEBUG (DevController:148) Waiting for devices tap.
[2007-10-25 16:03:19 2889] DEBUG (DevController:148) Waiting for devices vtpm.
[2007-10-25 16:04:41 2889] DEBUG (XendDomainInfo:445) XendDomainInfo.shutdown(halt)
[2007-10-25 16:04:41 2889] DEBUG (XendDomainInfo:959) XendDomainInfo.handleShutdownWatch
[2007-10-25 16:04:41 2889] INFO (XendDomainInfo:462) HVM save:remote shutdown dom 1!
[2007-10-25 16:04:41 2889] INFO (XendDomainInfo:1141) Domain has shutdown: name=domU id=1 reason=halt.
[2007-10-25 16:04:41 2889] DEBUG (XendDomainInfo:1713) XendDomainInfo.destroy: domid=1
[2007-10-25 16:04:41 2889] DEBUG (XendDomainInfo:1730) XendDomainInfo.destroyDomain(1)

$ cat /var/log/xen/xend-debug.log

Xend started at Thu Oct 25 16:00:45 2007.
Nothing to flush.
Traceback (most recent call last):
File "/usr/lib/python2.5/site-packages/xen/web/httpserver.py", line 140, in process
    resource = self.getResource()
File "/usr/lib/python2.5/site-packages/xen/web/httpserver.py", line 172, in getResource
    return self.getServer().getResource(self)
File "/usr/lib/python2.5/site-packages/xen/web/httpserver.py", line 351, in getResource
    return self.root.getRequestResource(req)
File "/usr/lib/python2.5/site-packages/xen/web/resource.py", line 39, in getRequestResource
    return findResource(self, req)
File "/usr/lib/python2.5/site-packages/xen/web/resource.py", line 26, in findResource
    next = resource.getPathResource(pathElement, request)
File "/usr/lib/python2.5/site-packages/xen/web/resource.py", line 49, in getPathResource
    val = self.getChild(path, request)
File "/usr/lib/python2.5/site-packages/xen/web/SrvDir.py", line 71, in getChild
    val = self.get(x)
File "/usr/lib/python2.5/site-packages/xen/xend/server/SrvDomainDir.py", line 52, in get
    return self.domain(x)
File "/usr/lib/python2.5/site-packages/xen/xend/server/SrvDomainDir.py", line 44, in domain
    dom = self.xd.domain_lookup(x)
File "/usr/lib/python2.5/site-packages/xen/xend/XendDomain.py", line 524, in domain_lookup
    raise XendInvalidDomain(str(domid))
XendInvalidDomain: <Fault 3: '1'>

$ cat /var/log/xen/qemu-dm.3737.log
domid: 1
qemu: the number of cpus is 1
Watching /local/domain/1/logdirty/next-active
qemu_map_cache_init nr_buckets = 4000
shared page at pfn 18fff
buffered io page at pfn 18ffd
xs_read(/vm/bed29a3d-94d8-c9ee-8f02-3e50de1a65ac/rtc/timeoffset): read error
xs_read(): vncpasswd get error. /vm/bed29a3d-94d8-c9ee-8f02-3e50de1a65ac/vncpasswd.
char device redirected to /dev/pts/1
I/O request not ready: 0, ptr: 0, port: 0, data: 0, count: 0, size: 0
Triggered log-dirty buffer switch

$ cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 15
model name : Intel(R) Core(TM)2 CPU          6300 @ 1.86GHz
stepping : 2
cpu MHz : 1866.780
cache size : 2048 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 10
wp : yes
flags : fpu tsc msr pae mce cx8 apic mtrr mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr lahf_lm
bogomips : 3737.92
clflush size : 64

processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 15
model name : Intel(R) Core(TM)2 CPU          6300 @ 1.86GHz
stepping : 2
cpu MHz : 1866.780
cache size : 2048 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 10
wp : yes
flags : fpu tsc msr pae mce cx8 apic mtrr mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr lahf_lm
bogomips : 3737.92
clflush size : 64

$ lspci
00:00.0 Host bridge: Intel Corporation 82975X Memory Controller Hub
00:01.0 PCI bridge: Intel Corporation 82975X PCI Express Root Port
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5 (rev 01)
00:1c.5 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 RAID bus controller: Intel Corporation 82801GR/GH (ICH7 Family) SATA RAID Controller (rev 01)
01:00.0 VGA compatible controller: ATI Technologies Inc RV515GL [FireGL V3300] (Primary)
01:00.1 Display controller: ATI Technologies Inc RV515GL [FireGL V3300] (Secondary)
3f:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5755 Gigabit Ethernet PCI Express (rev 02)

Here is the xml configuration file for the domU, which i got after running "virsh dumpxml domU"

$ cat domu.xml
<domain type='xen' id='1'>
<name>domU</name>
<uuid>bed29a3d94d8c9ee8f023e50de1a65ac</uuid>
<os>
    <type>hvm</type>
    <loader>/usr/lib/xen/boot/hvmloader</loader>
    <boot dev='cdrom'/>
</os>
<memory>512000</memory>
<currentMemory>409600</currentMemory>
<vcpu>1</vcpu>
<pci>routeirq</pci>
<on_poweroff>destroy</on_poweroff>
<on_reboot>restart</on_reboot>
<on_crash>restart</on_crash>
<features>
    <acpi/>
    <apic/>
</features>
<devices>
    <emulator>/usr/lib/xen/bin/qemu-dm</emulator>
    <interface type='bridge'>
      <source bridge='eth0'/>
      <mac address='00:16:3e:00:d0:a1'/>
      <script path='vif-bridge'/>
    </interface>
    <disk type='file' device='disk'>
      <driver name='file'/>
      <source file='/disk.imj'/>
      <target dev='hda'/>
    </disk>
    <disk type='block' device='cdrom'>
      <driver name='phy'/>
      <source dev='/dev/dvd'/>
      <target dev='hdc'/>
      <readonly/>
    </disk>
    <graphics type='vnc' port='5900' keymap='en-us'/>
    <console tty='/dev/pts/1'/>
</devices>
</domain>

Disclaimer:

This message and any attachment(s) contained here are information that is confidential, proprietary to NEC HCL System Technologies and its customers. Contents may be privileged or otherwise protected by law. The information is solely intended for the individual or the entity it is addressed to. If you are not the intended recipient of this message, you are not authorized to read, forward, print, retain, copy or disseminate this message or any part of it. If you have received this e-mail in error, please notify the sender immediately by return e-mail and delete it from your computer.

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users

WARNING - OLD ARCHIVES

xen-users

[Xen-users] Error creating domain U.