[Xen-users] Xen IP stack fails handoff to pluto in openswan

This one has me stumped.  I have openswan 2.3.0 installed on a xen 2.0.7
virtual machine running fedora core 3.  I've tried establishing tunnels
with a CyberGuard SG575 (FreeS/WAN), an old Super-FreeS/WAN gatway and a
Windows IPSec only client (lsipsectool -
http://sf.net/projects/lsipsectool).  I see the same symptom in all
cases so I suspect the problem is between openswan and xen.  Pluto never
see packets destined for it.

I've looked at this several ways.  I'll refer to the Xen openswan
gateway as XenOSW.  tcpdump on XenOSW sees that packets on eth0.  If I
log the packets on the INPUT chain of iptables on XenOSW, I see them
there, too.  I set plutodebug=all in ipsec.conf but I still do not see
any replies or initiations from the partner even though I see them on
the OUTPUT and INPUT chains and the eth0 interface.

In /var/log/secure I get plenty of:

Sep 17 13:31:14 NiagaraRASGW pluto[604]: | emitting length of ISAKMP
Vendor ID Payload: 20
Sep 17 13:31:14 NiagaraRASGW pluto[604]: | emitting length of ISAKMP
Message: 292
Sep 17 13:31:14 NiagaraRASGW pluto[604]: | sending 292 bytes for
main_outI1 through eth0:500 to x.x.x.188:500:

but never a reply and I never see any packet received messages from any
of the partners even though we see the packets on the interface.

Here are the INPUT chain iptables rules (which work perfectly on non Xen
openswan gateways):
Chain INPUT (policy DROP 0 packets, 0 bytes)
 pkts bytes target     prot opt in     out     source
destination
    8   560 ACCEPT     all  --  *      *       0.0.0.0/0
0.0.0.0/0           state RELATED,ESTABLISHED
    0     0 ACCEPT     tcp  --  *      *       0.0.0.0/0
0.0.0.0/0           tcp dpt:22 state NEW
    0     0 ACCEPT     tcp  --  lo     *       0.0.0.0/0
0.0.0.0/0
    0     0 ACCEPT     esp  --  *      *       0.0.0.0/0
0.0.0.0/0
    0     0 ACCEPT     udp  --  *      *       0.0.0.0/0
0.0.0.0/0           udp dpt:500
    0     0 ACCEPT     udp  --  *      *       0.0.0.0/0
0.0.0.0/0           udp dpt:4500
    0     0 VPN_ALLOW  all  --  *      *       0.0.0.0/0
0.0.0.0/0
    0     0 ACCESS_GROUPS_DENY  all  --  *      *       0.0.0.0/0
0.0.0.0/0
    0     0 ACCESS_GROUPS  all  --  *      *       0.0.0.0/0
0.0.0.0/0
    0     0 LOG        all  --  *      *       0.0.0.0/0
0.0.0.0/0           LOG flags 0 level 4 prefix `No Match: '

Here is OUTPUT:
Chain OUTPUT (policy DROP 0 packets, 0 bytes)
 pkts bytes target     prot opt in     out     source
destination
   30  5888 ACCEPT     all  --  *      *       0.0.0.0/0
0.0.0.0/0           state RELATED,ESTABLISHED
    0     0 ACCEPT     udp  --  *      *       0.0.0.0/0
0.0.0.0/0           udp dpt:53 state NEW
    0     0 ACCEPT     udp  --  *      *       0.0.0.0/0
0.0.0.0/0           udp dpt:123 state NEW
    0     0 ACCEPT     tcp  --  *      *       0.0.0.0/0
0.0.0.0/0           tcp dpt:22 state NEW
    0     0 ACCEPT     tcp  --  *      lo      0.0.0.0/0
0.0.0.0/0
    0     0 ACCEPT     esp  --  *      *       0.0.0.0/0
0.0.0.0/0
    3   960 ACCEPT     udp  --  *      *       0.0.0.0/0
0.0.0.0/0           udp dpt:500
    0     0 ACCEPT     udp  --  *      *       0.0.0.0/0
0.0.0.0/0           udp dpt:4500
    0     0 VPN_ALLOW  all  --  *      *       0.0.0.0/0
0.0.0.0/0
    0     0 ACCESS_GROUPS_DENY  all  --  *      *       0.0.0.0/0
0.0.0.0/0
    0     0 ACCESS_GROUPS  all  --  *      *       0.0.0.0/0
0.0.0.0/0
    0     0 LOG        all  --  *      *       0.0.0.0/0
0.0.0.0/0           LOG flags 0 level 4 prefix `No Match: '

The Xen host has two NICs.  All guests except the XenOSW use eth1 on
bridge xen-br0.

The XenOSW domU uses eth0 through bridge xen-br1 and has a manually
defined MAC address of 02:00:00:00:00:02.  There is no IP address bound
to eth0 or xen-br1 in dom0 (the host).  The IP address is bound in
XenOSW.  We do this because we do not want to expose the dom0 to the
Internet in any way.  However, we have tried it with a legitimate
address bound to the host eth0 and to bridge xen-br1.

The XenOSW domU does not start automatically as it is still a test
device.  Instead, after the dom0 boots, we do:
brctl addbr xen-br1
brctl addif xen-br1 eth0
ifconfig xen-br1 up

We then boot the XenOSW domU and all other traffic seems fine, e.g., the
iptables list was taken from an SSH session between my laptop and the
XenOSW.  Just Pluto is broken.

I have no idea what is wrong or even how to troubleshoot it.  The
packets just seem to fail on the handoff from the IP stack to the Pluto
application.  Any suggestions about either what is wrong or how to
troubleshoot it further? Many thanks to anyone willing to dive in this
deep! - John
-- 
John A. Sullivan III
Open Source Development Corporation
+1 207-985-7880
jsullivan@xxxxxxxxxxxxxxxxxxx

If you would like to participate in the development of an open source
enterprise class network security management system, please visit
http://iscs.sourceforge.net
-- 
John A. Sullivan III
Open Source Development Corporation
+1 207-985-7880
jsullivan@xxxxxxxxxxxxxxxxxxx

Financially sustainable open source development
http://www.opensourcedevel.com


_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
WARNING - OLD ARCHIVES

xen-users

[Xen-users] Xen IP stack fails handoff to pluto in openswan
