>I am curious about the use of B1NATS in the code
>around this patch. Under what circumstances does
>this get set/used?
1. emulate bsw1, bsw0
2. emulate rfi.
3. inject fault to guest.
There is similar unat code in
>fast_tick (default off) and fast_reflect (default on)
>and I am wondering if similar unat changes are needed
>and whether it is now OK to turn on HANDLE_AR_UNAT
>(which is now default off).
You are right, in above two cases you should also save ar.unat to
XSI_B1NATS_OFS after spilling the guest bank1to share page. I had handled all
this in C code. I didn't look into fast hypercall code, It's hard to read due
to I am not good at assembly code. The principle of handling ar.unat is
obvious; every time you spill banking register you must save corresponding
ar.unat after it, every time you fill banking register you must restore
corresponding ar.unat before it.
We don't need to clear all guest b0 registers and their's nat bit. Because
r16~r23 are preserved regs and r24~r31 are scratch regs, we only need to
restore r16~r23 rather than clear r16~r23 to 0.
Next time you enable some functions like hyper_ssm_i, when you save bank1 regs
you should also save bank1 unat.
Below patch enables HANDLE_AR_UNAT.
Signed-off-by Anthony Xu <Anthony.xu@xxxxxxxxx>
Thanks,
Anthony.
>-----Original Message-----
>From: Magenheimer, Dan (HP Labs Fort Collins) [mailto:dan.magenheimer@xxxxxx]
>Sent: 2005年11月3日 22:42
>To: Xu, Anthony
>Cc: xen-ia64-devel@xxxxxxxxxxxxxxxxxxx
>Subject: RE: ar.unat[patch] fixed this ar.uant issue.
>
>Hi Anthony --
>
>I am curious about the use of B1NATS in the code
>around this patch. Under what circumstances does
>this get set/used? There is similar unat code in
>fast_tick (default off) and fast_reflect (default on)
>and I am wondering if similar unat changes are needed
>and whether it is now OK to turn on HANDLE_AR_UNAT
>(which is now default off).
>
>Thanks,
>Dan
>
>> -----Original Message-----
>> From: Xu, Anthony [mailto:anthony.xu@xxxxxxxxx]
>> Sent: Thursday, November 03, 2005 1:08 AM
>> To: Magenheimer, Dan (HP Labs Fort Collins)
>> Cc: xen-ia64-devel@xxxxxxxxxxxxxxxxxxx
>> Subject: RE: ar.unat[patch] fixed this ar.uant issue.
>>
>> Dan,
>> Last time, I used ar.unat register to restore guest general
>> register nat bit in hyper_rfi function for eliminating nat
>> bit consumption fault,but not restored ar.unat.
>>
>> Signed-off-by Anthony Xu <Anthony.xu@xxxxxxxxx>
>>
>> Thanks,
>> Anthony.
>>
>>
>>
>>
>> >-----Original Message-----
>> >From: Magenheimer, Dan (HP Labs Fort Collins)
>> [mailto:dan.magenheimer@xxxxxx]
>> >Sent: 2005年11月3日 11:54
>> >To: Xu, Anthony
>> >Cc: xen-ia64-devel@xxxxxxxxxxxxxxxxxxx
>> >Subject: RE: ar.unat
>> >
>> >> I can take a look at this, please send me regcheck utilty.
>> >>
>> >>
>> >> Thanks
>> >> Anthony
>> >
>> >Great, thanks! Here's where I got Tony's regcheck tool. If
>> >it's not still there, perhaps Tony can post it.
>> >
>> >By the way, if anyone tries this on a domU, Matt Chapman
>> >has a pending fix that resolves a FP save/restore issue.
>> >
>> >Thanks,
>> >Dan
>> >
>> >> -----Original Message-----
>> >> From: linux-ia64-owner@xxxxxxxxxxxxxxx
>> >> [mailto:linux-ia64-owner@xxxxxxxxxxxxxxx] On Behalf Of Luck, Tony
>> >> Sent: Tuesday, March 01, 2005 4:33 PM
>> >> To: linux-ia64@xxxxxxxxxxxxxxx
>> >> Subject: RE: [patch 2.6.11-rc3-bk4] Correctly dereference
>> >> ia64_mca_data
>> >>
>> >> Back on February 9th, I wrote:
>> >> >I wrote a test program that loads up random values into registers
>> >> >(just r1-r31, a bunch of stacked registers, and f2-f127 for now)
>> >> >and then checks that all the registers haven't changed value a
>> >> >few thousand times, before reloading with a new set of random
>> >> >values.
>> >>
>> >> A few people asked whether I could post the program ... it took
>> >> a while to get sign-off ... but that gave me time to add "branch",
>> >> "predicate" and half a dozen "application" registers to the mix,
>> >> plus make it print the name of the register that was nuked (instead
>> >> of a number that required manual translation).
>> >>
>> >> I've tested it by using a debugger to zap one of each class
>> >> of register
>> >> that is being monitored to check that it works.
>> >>
>> >> http://www.kernel.org/pub/linux/kernel/people/aegl/ia64regcheck.tgz
>> >>
>> >> Usage ... compile, and run a few copies. If they all
>> "exit(0)" (which
>> >> may take a couple of days) the test passed. Otherwise you
>> should see
>> >> the name of the register printed to stderr, and exit code 1.
>> >>
>> >> Apart from the MCA case, I haven't seen it report a problem
>> >> yet ... but
>> >> I've only run a few hours.
>> >>
>> >> -Tony
>>
ar_unat2.patch
Description: ar_unat2.patch
_______________________________________________
Xen-ia64-devel mailing list
Xen-ia64-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-ia64-devel
|
Home