Bootdata ok (command line is root=/dev/sda1 ro quiet console=xvc xencons=xvc pciback.hide=(0000:01:00.0) reassigndev=0000:01:00.0 ) Linux version 2.6.18.8-xen (root@xentest) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #4 SMP Fri Apr 10 23:50:17 CEST 2009 BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000737d2000 (usable) DMI present. On node 0 totalpages: 466575 DMA zone: 4040 pages, LIFO batch:0 DMA32 zone: 462535 pages, LIFO batch:31 ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fb080 ACPI: XSDT (v001 A_M_I_ OEMXSDT 0x01000923 MSFT 0x00000097) @ 0x000000007cb70100 ACPI: FADT (v003 A_M_I_ OEMFACP 0x01000923 MSFT 0x00000097) @ 0x000000007cb70290 ACPI: MADT (v001 A_M_I_ OEMAPIC 0x01000923 MSFT 0x00000097) @ 0x000000007cb70390 ACPI: MCFG (v001 A_M_I_ OEMMCFG 0x01000923 MSFT 0x00000097) @ 0x000000007cb70400 ACPI: OEMB (v001 A_M_I_ AMI_OEM 0x01000923 MSFT 0x00000097) @ 0x000000007cb7e040 ACPI: HPET (v001 A_M_I_ OEMHPET 0x01000923 MSFT 0x00000097) @ 0x000000007cb78860 ACPI: GSCI (v001 A_M_I_ GMCHSCI 0x01000923 MSFT 0x00000097) @ 0x000000007cb7e0d0 ACPI: (v001 AMI OEMDMAR 0x00000001 MSFT 0x00000097) @ 0x000000007cb80100 >>> ERROR: Invalid checksum ACPI: SSDT (v001 DpgPmm CpuPm 0x00000012 INTL 0x20060113) @ 0x000000007cb811c0 ACPI: DSDT (v001 A1065 A1065000 0x00000000 INTL 0x20060113) @ 0x0000000000000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to xen Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 80000000 (gap: 7cc00000:82100000) Built 1 zonelists. Total pages: 466575 Kernel command line: root=/dev/sda1 ro quiet console=xvc xencons=xvc pciback.hide=(0000:01:00.0) reassigndev=0000:01:00.0 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Xen reported: 2666.364 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Software IO TLB enabled: Aperture: 2 megabytes Kernel range: ffff880003be4000 - ffff880003de4000 Address size: 22 bits PCI-DMA: Using software bounce buffering for IO (SWIOTLB) Memory: 1822456k/1892168k available (2453k kernel code, 60908k reserved, 1010k data, 188k init) Calibrating delay using timer specific routine.. 5334.78 BogoMIPS (lpj=26673946) Security Framework v1.0.0 initialized Capability LSM initialized Mount-cache hash table entries: 256 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 3072K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 SMP alternatives: switching to UP code ACPI: Core revision 20060707 SMP alternatives: switching to SMP code Initializing CPU#1 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 3072K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 Initializing CPU#2 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 3072K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 2 Brought up 4 CPUs Initializing CPU#3 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 3072K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 3 migration_cost=11 checking if image is initramfs... it is Freeing initrd memory: 17738k freed PM: Adding info for No Bus:platform NET: Registered protocol family 16 PM: Adding info for No Bus:xen PM: Adding info for No Bus:xen-backend ACPI: bus type pci registered PCI: Using configuration type 1 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing PM: Adding info for acpi:acpi Error attaching device data Error attaching device data Error attaching device data Error attaching device data ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PM: Adding info for No Bus:pci0000:00 Boot video device is 0000:00:02.0 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] PM: Adding info for pci:0000:00:00.0 PM: Adding info for pci:0000:00:02.0 PM: Adding info for pci:0000:00:02.1 PM: Adding info for pci:0000:00:03.0 PM: Adding info for pci:0000:00:19.0 PM: Adding info for pci:0000:00:1a.0 PM: Adding info for pci:0000:00:1a.1 PM: Adding info for pci:0000:00:1a.2 PM: Adding info for pci:0000:00:1a.7 PM: Adding info for pci:0000:00:1d.0 PM: Adding info for pci:0000:00:1d.1 PM: Adding info for pci:0000:00:1d.2 PM: Adding info for pci:0000:00:1d.7 PM: Adding info for pci:0000:00:1e.0 PM: Adding info for pci:0000:00:1f.0 PM: Adding info for pci:0000:00:1f.2 PM: Adding info for pci:0000:00:1f.3 PM: Adding info for pci:0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 *15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init PM: Adding info for No Bus:pnp0 pnp: ACPI device : hid PNP0A08 PM: Adding info for pnp:00:00 pnp: ACPI device : hid PNP0C01 PM: Adding info for pnp:00:01 pnp: ACPI device : hid PNP0200 PM: Adding info for pnp:00:02 pnp: ACPI device : hid PNP0B00 PM: Adding info for pnp:00:03 pnp: ACPI device : hid PNP0800 PM: Adding info for pnp:00:04 pnp: ACPI device : hid PNP0C04 PM: Adding info for pnp:00:05 pnp: ACPI device : hid PNP0C02 PM: Adding info for pnp:00:06 pnp: ACPI device : hid PNP0C02 PM: Adding info for pnp:00:07 pnp: ACPI device : hid PNP0103 PM: Adding info for pnp:00:08 pnp: ACPI device : hid INT0800 PM: Adding info for pnp:00:09 pnp: ACPI device : hid PNP0C02 PM: Adding info for pnp:00:0a pnp: ACPI device : hid PNP0501 PM: Adding info for pnp:00:0b pnp: ACPI device : hid PNP0C02 PM: Adding info for pnp:00:0c pnp: ACPI device : hid PNP0C02 PM: Adding info for pnp:00:0d pnp: ACPI device : hid PNP0C01 PM: Adding info for pnp:00:0e pnp: PnP ACPI: found 15 devices xen_mem: Initialising balloon driver. PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: the driver 'system' has been registered pnp: match found with the PnP device '00:01' and the driver 'system' pnp: match found with the PnP device '00:06' and the driver 'system' pnp: 00:06: ioport range 0x290-0x29f has been reserved pnp: match found with the PnP device '00:07' and the driver 'system' pnp: match found with the PnP device '00:0a' and the driver 'system' pnp: match found with the PnP device '00:0c' and the driver 'system' pnp: match found with the PnP device '00:0d' and the driver 'system' pnp: match found with the PnP device '00:0e' and the driver 'system' pciback: wants to seize 0000:01:00.0 pciback 0000:00:00.0: probing... pciback 0000:00:02.0: probing... pciback 0000:00:02.1: probing... pciback 0000:00:03.0: probing... pciback 0000:00:19.0: probing... pciback 0000:00:1a.0: probing... pciback 0000:00:1a.1: probing... pciback 0000:00:1a.2: probing... pciback 0000:00:1a.7: probing... pciback 0000:00:1d.0: probing... pciback 0000:00:1d.1: probing... pciback 0000:00:1d.2: probing... pciback 0000:00:1d.7: probing... pciback 0000:00:1e.0: probing... pciback 0000:00:1f.0: probing... pciback 0000:00:1f.2: probing... pciback 0000:00:1f.3: probing... pciback 0000:01:00.0: probing... pciback 0000:01:00.0: seizing device pciback 0000:01:00.0: pcistub_device_alloc pciback 0000:01:00.0: deferring initialization PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0 PCI: Bridge: 0000:00:1e.0 IO window: e000-efff MEM window: feb00000-febfffff PREFETCH window: fd800000-fdffffff PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered PM: Adding info for platform:pcspkr IA-32 Microcode Update Driver: v1.14a-xen audit: initializing netlink socket (disabled) audit(1239401016.016:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PM: Adding info for platform:vesafb.0 vesafb: framebuffer at 0xd0000000, mapped to 0xffffc20000080000, using 3072k, total 32704k vesafb: mode is 1024x768x16, linelength=2048, pages=0 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12ac Non-volatile memory driver v1.2 RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize loop: loaded (max 8 devices) e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k4 e1000e: Copyright (c) 1999-2008 Intel Corporation. GSI 16 sharing vector 0xD0 and IRQ 16 ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:19.0 to 64 eth0: (PCI Express:2.5GB/s:Width x1) 00:23:54:9a:46:ea eth0: Intel(R) PRO/1000 Network Connection eth0: MAC: 7, PHY: 8, PBA No: ffffff-0ff Intel(R) Gigabit Ethernet Network Driver - version 1.2.45-k2 Copyright (c) 2008 Intel Corporation. Xen virtual console successfully installed as xvc0 Event-channel device installed. netfront: Initialising virtual ethernet driver. pciback: pcistub_init_devices_late pciback 0000:01:00.0: initializing... pciback 0000:01:00.0: initializing config pciback 0000:01:00.0: initializing virtual configuration space pciback 0000:01:00.0: added config field at offset 0x04 pciback 0000:01:00.0: added config field at offset 0x3c pciback 0000:01:00.0: added config field at offset 0x3d pciback 0000:01:00.0: added config field at offset 0x0c pciback 0000:01:00.0: added config field at offset 0x0d pciback 0000:01:00.0: added config field at offset 0x0f pciback 0000:01:00.0: added config field at offset 0x10 pciback 0000:01:00.0: added config field at offset 0x14 pciback 0000:01:00.0: added config field at offset 0x18 pciback 0000:01:00.0: added config field at offset 0x1c pciback 0000:01:00.0: added config field at offset 0x20 pciback 0000:01:00.0: added config field at offset 0x24 pciback 0000:01:00.0: added config field at offset 0x30 pciback 0000:01:00.0: Found capability 0x1 at 0x40 pciback 0000:01:00.0: added config field at offset 0x40 pciback 0000:01:00.0: added config field at offset 0x42 pciback 0000:01:00.0: added config field at offset 0x44 pciback 0000:01:00.0: added config field at offset 0x46 pciback 0000:01:00.0: added config field at offset 0x47 pciback 0000:01:00.0: enabling device PCI: Enabling device 0000:01:00.0 (0000 -> 0003) GSI 17 sharing vector 0x21 and IRQ 17 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 17 pciback 0000:01:00.0: reset device ACPI: PCI interrupt for device 0000:01:00.0 disabled Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx pnp: the driver 'ide' has been registered pnp: the driver 'i8042 kbd' has been registered pnp: the driver 'i8042 aux' has been registered pnp: the driver 'i8042 kbd' has been unregistered pnp: the driver 'i8042 aux' has been unregistered PNP: No PS/2 controller found. Probing ports directly. PM: Adding info for platform:i8042 serio: i8042 AUX port at 0x60,0x64 irq 12 PM: Adding info for serio:serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 PM: Adding info for serio:serio1 mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 NET: Registered protocol family 1 NET: Registered protocol family 17 ACPI: (supports S0 S1 S3 S4 S5) BIOS EDD facility v0.16 2004-Jun-25, 1 devices found Freeing unused kernel memory: 188k freed ACPI (exconfig-0455): Dynamic SSDT Load - OemId [DpgPmm] OemTableId [ P001Ist] [20060707] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ P001Cst] [20060707] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI (exconfig-0455): Dynamic SSDT Load - OemId [DpgPmm] OemTableId [ P002Ist] [20060707] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ P002Cst] [20060707] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) ACPI (exconfig-0455): Dynamic SSDT Load - OemId [DpgPmm] OemTableId [ P003Ist] [20060707] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ P003Cst] [20060707] ACPI: CPU2 (power states: C1[C1] C2[C2] C3[C3]) ACPI (exconfig-0455): Dynamic SSDT Load - OemId [DpgPmm] OemTableId [ P004Ist] [20060707] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ P004Cst] [20060707] ACPI: CPU3 (power states: C1[C1] C2[C2] C3[C3]) udev: renamed network interface eth0 to eth1 usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1a.0 to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1a.0: irq 17, io base 0x0000d400 PM: Adding info for usb:usb1 PM: Adding info for No Bus:usbdev1.1_ep00 usb usb1: configuration #1 chosen from 1 choice PM: Adding info for usb:1-0:1.0 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected SCSI subsystem initialized libata version 2.00 loaded. PM: Adding info for No Bus:usbdev1.1_ep81 GSI 18 sharing vector 0x29 and IRQ 18 ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1a.1 to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1a.1: irq 18, io base 0x0000d480 PM: Adding info for usb:usb2 PM: Adding info for No Bus:usbdev2.1_ep00 usb usb2: configuration #1 chosen from 1 choice PM: Adding info for usb:2-0:1.0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev2.1_ep81 GSI 19 sharing vector 0x31 and IRQ 19 ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 18 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1a.2 to 64 uhci_hcd 0000:00:1a.2: UHCI Host Controller uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.2: irq 19, io base 0x0000d800 PM: Adding info for usb:usb3 PM: Adding info for No Bus:usbdev3.1_ep00 usb usb3: configuration #1 chosen from 1 choice PM: Adding info for usb:3-0:1.0 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev3.1_ep81 GSI 20 sharing vector 0x39 and IRQ 20 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000cc00 PM: Adding info for usb:usb4 PM: Adding info for No Bus:usbdev4.1_ep00 usb usb4: configuration #1 chosen from 1 choice PM: Adding info for usb:4-0:1.0 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev4.1_ep81 GSI 21 sharing vector 0x41 and IRQ 21 ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000d000 PM: Adding info for usb:usb5 PM: Adding info for No Bus:usbdev5.1_ep00 usb usb5: configuration #1 chosen from 1 choice PM: Adding info for usb:5-0:1.0 hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev5.1_ep81 ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.2: irq 19, io base 0x0000d080 PM: Adding info for usb:usb6 PM: Adding info for No Bus:usbdev6.1_ep00 usb usb6: configuration #1 chosen from 1 choice PM: Adding info for usb:6-0:1.0 hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev6.1_ep81 ahci 0000:00:1f.2: version 2.0 GSI 22 sharing vector 0x49 and IRQ 22 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 22 (level, low) -> IRQ 22 usb 5-1: new low speed USB device using uhci_hcd and address 2 PM: Adding info for usb:5-1 PM: Adding info for No Bus:usbdev5.2_ep00 usb 5-1: configuration #1 chosen from 1 choice PM: Adding info for usb:5-1:1.0 PM: Adding info for No Bus:usbdev5.2_ep81 PM: Adding info for usb:5-1:1.1 PM: Adding info for No Bus:usbdev5.2_ep82 usbcore: registered new driver hiddev input: Logitech USB Receiver as /class/input/input0 input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.1-1 input: Logitech USB Receiver as /class/input/input1 input,hiddev96: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.1-1 usbcore: registered new driver usbhid /usr/src/xen-unstable.hg/linux-2.6.18-xen.hg/drivers/usb/input/hid-core.c: v2.6:USB HID core driver PCI: Setting latency timer of device 0000:00:1f.2 to 64 ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pmp pio slum part ata1: SATA max UDMA/133 cmd 0xFFFFC2000000C100 ctl 0x0 bmdma 0x0 irq 254 ata2: SATA max UDMA/133 cmd 0xFFFFC2000000C180 ctl 0x0 bmdma 0x0 irq 254 ata3: SATA max UDMA/133 cmd 0xFFFFC2000000C200 ctl 0x0 bmdma 0x0 irq 254 ata4: SATA max UDMA/133 cmd 0xFFFFC2000000C280 ctl 0x0 bmdma 0x0 irq 254 ata5: SATA max UDMA/133 cmd 0xFFFFC2000000C300 ctl 0x0 bmdma 0x0 irq 254 ata6: SATA max UDMA/133 cmd 0xFFFFC2000000C380 ctl 0x0 bmdma 0x0 irq 254 scsi0 : ahci PM: Adding info for No Bus:host0 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7, max UDMA/100, 156301488 sectors: LBA48 NCQ (depth 31/32) ata1.00: ata1: dev 0 multi count 0 ata1.00: configured for UDMA/100 scsi1 : ahci PM: Adding info for No Bus:host1 ata2: SATA link down (SStatus 0 SControl 300) scsi2 : ahci PM: Adding info for No Bus:host2 ata3: SATA link down (SStatus 0 SControl 300) scsi3 : ahci PM: Adding info for No Bus:host3 ata4: SATA link down (SStatus 0 SControl 300) scsi4 : ahci PM: Adding info for No Bus:host4 ata5: SATA link down (SStatus 0 SControl 300) scsi5 : ahci PM: Adding info for No Bus:host5 ata6: SATA link down (SStatus 0 SControl 300) PM: Adding info for No Bus:target0:0:0 Vendor: ATA Model: WDC WD800JD-60MS Rev: 10.0 Type: Direct-Access ANSI SCSI revision: 05 PM: Adding info for scsi:0:0:0:0 ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7 ehci_hcd 0000:00:1a.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1a.7 ehci_hcd 0000:00:1a.7: irq 19, io mem 0xfe9f9000 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 PM: Adding info for usb:usb7 PM: Adding info for No Bus:usbdev7.1_ep00 usb usb7: configuration #1 chosen from 1 choice PM: Adding info for usb:7-0:1.0 hub 7-0:1.0: USB hub found hub 7-0:1.0: 6 ports detected SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 < sda5 > sd 0:0:0:0: Attached scsi disk sda PM: Adding info for No Bus:usbdev7.1_ep81 ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfe9f8000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 PM: Adding info for usb:usb8 PM: Adding info for No Bus:usbdev8.1_ep00 usb usb8: configuration #1 chosen from 1 choice PM: Adding info for usb:8-0:1.0 hub 8-0:1.0: USB hub found hub 8-0:1.0: 6 ports detected usb 5-1: USB disconnect, address 2 PM: Removing info for No Bus:usbdev5.2_ep81 PM: Removing info for usb:5-1:1.0 PM: Removing info for No Bus:usbdev5.2_ep82 PM: Removing info for usb:5-1:1.1 PM: Removing info for No Bus:usbdev5.2_ep00 PM: Removing info for usb:5-1 PM: Adding info for No Bus:usbdev8.1_ep81 EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. usb 5-1: new low speed USB device using uhci_hcd and address 3 PM: Adding info for usb:5-1 PM: Adding info for No Bus:usbdev5.3_ep00 usb 5-1: configuration #1 chosen from 1 choice PM: Adding info for usb:5-1:1.0 input: Logitech USB Receiver as /class/input/input2 input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.1-1 PM: Adding info for No Bus:usbdev5.3_ep81 PM: Adding info for usb:5-1:1.1 input: Logitech USB Receiver as /class/input/input3 input,hiddev96: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.1-1 PM: Adding info for No Bus:usbdev5.3_ep82 kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. udevd version 125 started ts: Compaq touchscreen protocol output input: PC Speaker as /class/input/input4 ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 19 PM: Adding info for No Bus:i2c-0 Adding 3229024k swap on /dev/sda5. Priority:-1 extents:1 across:3229024k EXT3 FS on sda1, internal journal ieee1394: Initialized config rom entry `ip1394' ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) ieee1394: sbp2: Try serialize_io=0 for better performance Netfilter messages via NETLINK v0.30. ip_conntrack version 2.4 (8192 buckets, 65536 max) - 304 bytes per conntrack ip_tables: (C) 2000-2006 Netfilter Core Team eth1: Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX eth1: 10/100 speed: disabling TSO NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver IN=eth1 OUT= MAC=00:23:54:9a:46:ea:00:12:f0:27:eb:b8:08:00 SRC=172.16.1.20 DST=172.16.1.235 LEN=48 TOS=0x00 PREC=0x00 TTL=128 ID=53909 DF PROTO=TCP SPT=1443 DPT=22 WINDOW=64512 RES=0x00 SYN URGP=0 Bridge firewalling registered suspend: event channel 26 eth1: no IPv6 routers present xenbr0: no IPv6 routers present