Hi all,
I've been trying to boot Linux 2.6.16.16 as dom0 for a few days now but
I can't work out how to get XenLinux to recognise my disk. It's
looking like a bug in Xen, as booting the same version of Linux without
Xen works fine.
Does anyone know of any issues with the ata_piix (Intel ICH5/6) driver
and SATA disks? Has anyone got this configuration going?
Boot messages follow. This is with Xen 3.0.2-2.
Thanks,
Adam.
Messages from Xen kernel:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
hda: TEAC DVD+RW DV-W58E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Adaptec aacraid driver (1.1-4 Jun 5 2006 11:53:11)
ata1: SATA max UDMA/133 cmd 0xFE00 ctl 0xFE12 bmdma 0xFEA0 irq 5
ata2: SATA max UDMA/133 cmd 0xFE20 ctl 0xFE32 bmdma 0xFEA8 irq 5
ata1: dev 0 ATA-6, max UDMA/133, 78125000 sectors: LBA
ata1: qc timeout (cmd 0xef) <-- bad
ata1: failed to set xfermode, disabled <-- bad
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
ATA: abnormal status 0xFF on port 0xFE27 <-- normal
ata2: disabling port
scsi1 : ata_piix
Messages from native kernel:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 169
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
hda: TEAC DVD+RW DV-W58E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Adaptec aacraid driver (1.1-4 Jun 6 2006 11:16:39)
ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 20 (level, low) -> IRQ 217
ata1: SATA max UDMA/133 cmd 0xFE00 ctl 0xFE12 bmdma 0xFEA0 irq 217
ata2: SATA max UDMA/133 cmd 0xFE20 ctl 0xFE32 bmdma 0xFEA8 irq 217
ata1: dev 0 ATA-6, max UDMA/133, 78125000 sectors: LBA
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
ATA: abnormal status 0xFF on port 0xFE27
ata2: disabling port
scsi1 : ata_piix
Vendor: ATA Model: WDC WD400JD-75HK Rev: 14.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 78125000 512-byte hdwr sectors (40000 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 78125000 512-byte hdwr sectors (40000 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: Attached scsi disk sda
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
|
Home